• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.199-201
• /
• 2006

The wetting balance test was carried out to compare the wettability of Sn-Xwt%Cu($0{\sim}3$wt%) solders. And, IMCs which were formed at interface between solders and substrates were investigated by using XRD(x-ray diffractometer), SEM(scanning electron microscope) and EDS(energy dispersive spectroscope). The value of ${\gamma}_[fl}$ and(${\gamma}_{fs}-{\gamma}_{ls}$) had a tendency to increase with increasing wetting temperature. The activation energy that was calculated between the bare Cu substrate and flux was increased in the following order Sn-0.7wt%Cu(68.42 kJ/mol);Sn-3.0wt%Cu(72.66 kJ/mol);100wt%Sn solder(94.53 kJ/mol).

• Applied Science and Convergence Technology
• /
• 제23권6호
• /
• pp.345-350
• /
• 2014

The surface oxidation mechanism of lead-free solder alloys has been investigated with multiple reflow using X-ray photoelectron spectroscopy. It was found that the solder surface of Sn-Ag-Cu-In solder alloy is surrounded by a thin $InO_x$ layer after reflow process; this coating protects the metallic surface from thermal oxidation. Based on this result, we have performed a wetting balance test at various temperatures. The Sn-Ag-Cu-In solder alloy shows characteristics of both thermal oxidation and wetting balance better than those of Sn-Ag-Cu solder alloy. Therefore, Sn-Ag-Cu-In solder alloy is a good candidate to solve the two problems of easy oxidation and low wettability, which are the most critical problems of Pb-free solders.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.219-221
• /
• 2005

Sn-9Zn solder balls were bonded to Cu, ENIG (Electroless Nickel/Immersion Gold) and electrolytic Au/Ni pads, and the effect of aging on their joint reliability was investigated. The interfacial products were different from the general reaction layer formed in a Sn-base solder. The intermetallic compounds formed in the solder/Cu joint were $Cu_{5}Zn_{8}$ and $Cu_{6}Sn_{5}$. After aging treatment, voids formed irregularly at the bottom side of the solder because of Sn diffusion into the $Cu_{5}Zn_{8}$ IMC. In the case of the solder/ENIG joint, $AuZn_{3}$ IMCs were formed at the interface. In the case of the Au/Ni/Cu substrate, an $AuZn_{3}$ IMC layer formed at the interface due to the fast reaction between Au and Zn. In addition, the $AuZn_{3}$ IMC layer became detached from the interface after reflow. When the aging time was extended to 100 h, $Ni_{5}Zn_{21}$ IMC was observed on the Ni substrate.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.63-67
• /
• 2003

Electromigration characteristics of $SnAg_3Cu_{0.7}$ and eutectic SnPb solder were studied using thin stripe-type test structures. Significant changes in the microstructure of two solders were observed after electromigration test, in which the temperature and the current density were varied from 90 to $110^{\circ}C$ and from $4.0\times10^4\;A/cm^2\;to\;9.2\times10^4\;A/cm^2$. In SnAgCu solders, hillocks were main]y observed near the anode end. From resistance measurements, it was calculated that the activation energy of the SnAgCu solder for electromigration was 1.04 eV And in eutectic SnPb without the effect of pads, while depleted region was found near cathode end, Sn-rich hillocks were observed near the anode end. During eutectic SnPb electromigration, it were observed that electromigration behavior had two migration modes.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.126-129
• /
• 2002

This article presents that the affecting factors to solderability and initial reliability. It was discussed that effect of the solder ball hardness and composition on the reliability of solder joints. In this study, lead free solder alloys with compositions of Sn-Cu, Sn-Ag, Sn-Ag-Cu, Sn-Ag-Cu-Bi were applied to the $\muBGA$ packages. As a result of experiments, the high degree of hardness with the displacement of 0.22mm was obtained Sn-2.0Ag-0.7Cu-3.0Bi. The shear strength of lead free solder was higher than of Sn-37Pb solder, and it was increased about 150% in Sn-2.0Ag-0.7Cu-3.0Bi.

• 대한금속재료학회지
• /
• 제46권1호
• /
• pp.33-38
• /
• 2008

The interfacial reactions and shear strength of pure Sn solder bump were investigated with different under bump metallizations (UBMs) and reflow numbers. Two different UBMs were employed in this study: Cu and Ni. Cu6Sn5 and Cu3Sn intermetallic compounds (IMCs) were formed at the bump/Cu UBM interface, whereas only a Ni3Sn4 IMC was formed at the bump/Ni UBM interface. These IMCs grew with increasing reflow number. The growth of the Cu-Sn IMCs was faster than that of the Ni-Sn IMC. These interfacial reactions greatly affected the shear properties of the bumps.

• 마이크로전자및패키징학회지
• /
• 제22권2호
• /
• pp.47-53
• /
• 2015

인쇄회로기판 솔더 상부 및 하부 접합부의 서로 다른 표면처리 조건에 따른 Sn-3.0Ag-0.5Cu (SAC305) 접합부의 열처리 및 전류 인가에 따른 금속간 화합물 성장거동을 비교하기 위하여 in-situ 미세구조분석 및 electromigration (EM) 수명평가를 실시하였다. 솔더 접합 직후, 상부 접합부의 electroless nickel immersion gold (ENIG) 표면처리에서는 $(Cu,Ni)_6Sn_5$, 하부 접합부의 organic solderability preservative (OSP) 표면처리에서는$ Cu_6Sn_5$, $Cu_3Sn$ 금속간 화합물이 접합 계면에서 생성되었다. EM 수명평가 결과 온도 $130^{\circ}C$, 전류밀도 $5.0{\times}10^3A/cm^2$ 하에서 평균파괴시간이 약 78.7 hrs으로 도출되었고, 하부 OSP 표면처리에서 전자가 솔더로 빠져나가는 부분에서 Cu의 소모에 의한 단락이 주 손상기구로 확인되었다. In-situ 주사전자현미경을 통해 계면 미세구조 분석 결과 상부 접합부 ENIG 표면처리에서 전자의 방향에 따른 미세구조의 큰 차이가 없고 뚜렷한 손상이 관찰되지 않았으나, 하부 접합부 OSP 표면처리의 경우 전자가 솔더로 유입되는 부분에서 빠른 Cu 소모로 인한 보이드 성장이 관찰되었다. 따라서, SAC305무연솔더 접합부에서 ENIG 표면처리가 OSP 표면처리보다 보다 우수한 EM확산방지막 역할을 하여 금속간 화합물 성장을 억제하고 보다 우수한 EM 신뢰성을 보이는 것으로 판단된다.

• 한국재료학회지
• /
• 제9권3호
• /
• pp.288-294
• /
• 1999

솔더 범프를 사용하는 플립 칩 접속기술에서 범프와 칩 사이에 위치하는 금속 충들의 조합을 UBM(Under Bump Metallurgy)라고 부르며 이 UBM을 어떤 조합으로 사용하는 가에 따라 접속의 안정성이 크게 좌우된다. 본 연구에서는 UBM중에서 솔더 접착 층으로 사용되는 구리 층의 두께를 $1\mu\textrm{m}와 5\mu\textrm{m}$로 하는 한편 barrier 층으로 사용되는 금속 층을 Ti, Ni, Pd으로 변화시키면서 이들 UBM과 공정 납-주석 사이의 계면반응을 살펴보았다. 이를 위해 $100\mu\textrm{m}$ 크기의 솔더 범프를 전해도금법을 사용하여 제작하고 리플로 횟수와 시효시간에 따른 각 UBM에서의 금속간 화합물의 성장을 관찰하였다. $Cu_6Sn_5 \eta'$-상 금속간 화합물이 모든 조건에서 형성되었고 Cu층의 두께가 $5\mu\textrm{m}$로 두꺼운 경우에는 $Cu_3Sn \varepsilon$-상도 관찰되었다. Pd을 사용한 UBM 구조에서는 시효 처리시에 $Cu_6Sn_5$ 상 아래쪽에 $PdSn_4$상이 형성되었다. 또한 이들 계면에서의 금속간 화합물의 성장은 솔더 범프의 접속강도 값과 밀접한 관계를 가진다.

• 마이크로전자및패키징학회지
• /
• 제26권3호
• /
• pp.81-88
• /
• 2019

본 연구에서는 그래핀 산화(graphene oxide, GO) 분말 첨가가 ball grid array(BGA) 패키지와 printed circuit board(PCB)간 Sn-3.0Ag-0.5Cu(SAC305) 무연솔더 접합부의 electromigration(EM) 수명에 미치는 영향에 대하여 보고 하였다. 솔더 접합 직후, Ni/Au표면처리된 패키지 접합계면에서는 $(Cu,Ni)_6Sn_5$가 생성되었으며 organic solderability preservative(OSP) 표면처리 된 PCB 접합계면에서는 $Cu_6Sn_5$ 금속간화합물(intermetallic compound, IMC)이 생성되었다. $130^{\circ}C$, $1.0{\times}10^3A/cm^2$ 전류밀도 하에서 EM 수명평가 결과, GO를 첨가하지 않은 솔더 접합부의 평균 파괴 시간은 189.9 hrs으로 도출되었고, GO를 첨가한 솔더 접합부의 평균 파괴 시간은 367.1 hrs으로 도출되었다. EM에 의한 손상은 패키지 접합계면에 비하여 pad 직경이 작은 PCB 접합계면에서 전자 유입에 의한 Cu의 소모로 인하여 발생하였다. 한편, 첨가된 GO는 하부계면의 $Cu_6Sn_5$ IMC와 솔더 사이에 분포하는 것을 확인하였다. 따라서, SAC305 무연솔더에 첨가된 GO가 전류 집중 영역에서 Cu의 빠른 확산을 억제하여 우수한 EM 신뢰성을 갖는 것으로 생각된다.

• 한국전기전자재료학회논문지
• /
• 제25권12호
• /
• pp.974-978
• /
• 2012

The effect of Cu coating on the sensing properties of nano $SnO_2:Cu$ based sensors for the $CH_4$, $CH_3CH_2CH_3$ gas was studied. This work was focussed on investigating the change of sensitivity of nano $SnO_2:Cu$ based sensors for $CH_4$, $CH_3CH_2CH_3$ gas by Cu coating. Nano sized $SnO_2$ powders were prepared by solution reduction method using stannous chloride($SnCl_2{\cdot}2H_2O$), hydrazine($N_2H_2$) and NaOH and subsequent heat treatment. XRD patterns showed that nano $SnO_2$ powders with rutile structure were grown with (110), (101), (211) dominant peak. The particle size of nano $SnO_2:Cu$ powders at 8 wt% Cu was about 50 nm. $SnO_2$ particles were found to contain many pores, according to SEM analysis. The sensitivity of nano $SnO_2:Cu$ based sensors was measured for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature by comparing the resistance in air with that in target gases. The sensitivity for both $CH_4$ and $CH_3CH_2CH_3$ gases was improved by Cu coating on the nano $SnO_2$ surface. The response time and recovery time of the $SnO_2:Cu$ gas sensors for the $CH_4$ and $CH_3CH_2CH_3$ gases were 18~20 seconds, and 13~15 seconds, respectively.