• Journal of the Korean Electrochemical Society
• /
• v.24 no.3
• /
• pp.35-41
• /
• 2021

In this study, the effect of zwitterionic surfactant on Cu electrodeposition was investigated through cyclic voltammetry. With the addition of (dodecyldimethylammonio)propanesulfonate (DDAPS) as a representative zwitterionic surfactant in the electrolyte for Cu electrodeposition, the electrochemical Cu²⁺ reduction was inhibited on Cu and glassy carbon electrodes. Its inhibition effect was similar to that of cationic surfactant rather than anionic surfactant. Moreover, DDAPS interacted with chloride ion and exhibited the mass transfer-dependent inhibition behavior, which indicates that its inhibition function is associated with the formation of its surface aggregates on anion-covered Cu surface. In addition, adsorbed DDAPS slightly reduced the surface roughness of Cu electrodeposits. These characteristics were similar to those of cationic surfactant, but less obvious. It means the effect of DDAPS on Cu electrodeposition originates from the cationic head group which is shield by anionic head group.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.251-257
• /
• 1996

The present paper represents the results of development and first experimental tests of a new ionized cluster beam (ICB) source. The novelty of ICB source lies in the fact that the crucible and ionization parts are spaced in one cylindrical shell but are not divided in an electric circuit. The ICB source adapts permanent magnets to increase the ionization efficiency. The maximum obtained $Cu^+$ ion current denisity is $1.5{\mu}A/\textrm{cm}^2$, therewith the ionization rate amounts 3% under deposition rate is 0.2$\AA$/s and the acceleration voltage is 4 kV, the $Cu^+$ ion beam uniformity is better than 95%.

• Journal of Magnetics
• /
• v.2 no.1
• /
• pp.7-11
• /
• 1997

The dependence of magnetoresistance (MR) ratio on various variables like the thickness of the second Co layer, on the presence of cap layer, on deposition field (Hdep) and on annealing in Co/Cu/Co sandwiches was investigated. Spin-valve sandwiches were deposited on the corning glass by means of the 3-gun dcmagnetron sputtering at a 5 mTorr partial Ar pressure and room temperature. The deposition field was varied from 70 Oe to 720 Oe. The MR curve was measured by the four-terminal method with applied magnetic field up to 1000 Oe perpendicular to the direction of a current in the film plne. The MR ratio of glass/Fe(50${\AA}$)/Co(17${\AA}$)/Cu(24${\AA}$)/Cot(${\AA}$) fabricated by making 50 ${\AA}$ of Fe buffer layer has the maximum value of 8.2% when the thickness of the second Co layer was 17${\AA}$and the deposition field was 350 Oe. In the case of glass/Fe(50${\AA}$)/Co(17${\AA}$)/Cu(24${\AA}$)/Cot(${\AA}$) with Cu cap layer on top, the decrease in the MR ratio seemed to relate with the oxidation of the second Co layer. Samples prepared with deposition field showed greater MR ratios through the formation of more complete spin valve films. After annealing for 2 hours at 300$^{\circ}C$, the MR ratio of the samples prepared with deposition field decreased rapidly while the MR raito of the sample prepared without the field remained.

• Korean Journal of Poultry Science
• /
• v.41 no.4
• /
• pp.241-247
• /
• 2014

The objective of this experimental was to investigate the effect of dietary Cu-sulfate and Cu-soy proteinate on productive performance and small intestinal microflora. A total 1,000 Hy-Line Brown laying hens (35 weeks old) were randomly allotted to 1 of 5 dietary treatments: Control, Cu-sulfate 50, 100 (50, 100 ppm Cu supplementation as Cu-sulfate) and Cu-SP 50, 100 (50, 100 ppm Cu supplementation as Cu-soy proteinate). Each treatment was replicated 4 times with fifty birds per replication, housed in 2 birds cages. Fifty birds units were arranged according to randomized block design. Feeding trial lasted 5 weeks under 16L : 8D lighting regimen. Hen day egg production was significantly (P<0.05) higher in Cu treated groups than control. Feed intake, broken and shell-less egg production was not significantly influenced by treatment. Eggshell color, eggyolk color, haugh unit, and eggshell thickness were not significantly influenced by treatment. However, eggshell strength was significantly (P<0.05) greater in Cu treated groups than control. Concentration of copper of liver was significantly (P<0.05) greater in Cu treated groups than control. Concentration of zinc and iron of liver were not influenced by treatments. Population of Cl. perfrigens and Lactobacilli in the small intestinal content were significantly (P<0.05) influenced by treatments. Population of Cl. perfrigens decreased and that of Lactobacilli increased in the Cu supplement groups. In conclusion, dietary Cu sulfate and Cu-soy proteinate similarly improves egg production, eggshell strength, and favors intestinal microbial population of laying hens.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1129-1134
• /
• 2015

In this article, a study of a flower like nanostructured CdS buffer layer for improving the performance of a submicron-thick $CuIn_{1-x}Ga_xSe_2$ (CIGS) solar cell (SC) is presented. Both its synthesis and properties are discussed in detail. The surface reflectance of the device is dramatically decreased. SCs with flower like nanostructured CdS buffer layers enhance short-circuit current density, fill factor, and open-circuit voltage. These enhancements contribute to an increase in power conversion efficiency of about 55% on average compared to SCs that don't have a flower like nanostructured CdS buffer layer, despite them both having the same CIGS light absorbing layer.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.53-57
• /
• 2013

Although the lowering of Ag content in Sn-3.0Ag-0.5Cu is known to improve the mechanical shock reliability of the solder joint, it is also known to be detrimental to the solderbility. In this study, the quaternary alloying effect of In and the minor alloying effects of Mn and Pd on the solderability, thermal cycling and mechanical shock reliabilities of the low Ag content Sn-1.2Ag-0.7Cu solder were investigated using board-level BGA packages. The solderability of Sn-1.2Ag-0.7Cu-0.4In was proved to be comparable to that of Sn-3.0Ag-0.5Cu but its thermal cycling reliability was inferior to that of Sn-3.0Ag-0.5Cu. While the 0.03 wt% Pd addition to the Sn-1.2Ag-0.7Cu-0.4In decreased the solderability and reliabilities of solder joint, the 0.1 wt% Mn addition was proved to be beneficial especially for the mechanical shock reliability compared to those of Sn-3.0Ag-0.5Cu and Sn-1.0Ag-0.5Cu compositions. It was considered to be due that the Mn addition decreased the Young's modulus of low Ag content Pb-free solders.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.2
• /
• pp.145-156
• /
• 1999

The distribution of the second phase, the change of transformation temperature and mechanical properties with thermomechanical treatment conditions were investigated by metallography, calorimetry, EDS, tensile test and fractography in a Cu-Al-Ni-Ti-Mn alloy. The cast structure revealed Ti-rich precipitates($X_L$ phase) between dendrite arms, which have been identified as $(Cu,Ni)_2TiAl$ intermetallic compounds. By homogenizing above $900^{\circ}C$, the $X_L$ phase was melted in the matrix, while the Xs phase was precipitated in matrix and the volume fraction of it was increased. When hot-rolled specimen was betatized below $750^{\circ}C$, recrystallization could not be observed. However, the specimen betatized above $800^{\circ}C$ was recrystallized and the grain size was about $50{\mu}m$, while Xs phase was precipitated in matrix. With raising betatizing temperature, $M_s$ and $A_s$ temperatures were fallen and transformation hysteresis became larger. The strain of the specimen betatized at $800^{\circ}C$ was 8.2% as maximum value. The maximum shape recovery rate could be obtained in the specimen betatized at $800^{\circ}C$ but it was decreased due to the presence of Xs phase with increasing betatizing temperature.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.2
• /
• pp.139-147
• /
• 2019

Incorporation of CuO nanoparticles during the polymerization of aniline in the presence of ammonium peroxydisulphate as an oxidizing agent and sodium salt of dodecylbenzene sulphonic acid as dopant as well as surfactant yielded water soluble CuO-PANI composite. Comparison of recorded spectra like FTIR, XRD and SEM with reported one confirm the formation of the composite. Analysis by gravimetric method exposes that the synthesized composite is having resistivity against corrosion, with slight variation in efficiency on extending the time duration up to eight hours in strong acidic condition. OCP measurement, potentiodynamic polarization and EIS studies also confirms the suppression ability of composite against corrosion. Riskless working environment could be provided by the synthesized composite during industrial cleaning process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.339-344
• /
• 2017

An all-transparent photodetector was fabricated by structuring $Cu_2O$/ZnO/AZO/ITO on a glass substrate. The visible-range transmittance was as high as 80%, which ensures clear vision forhuman eyes. High-transparency metal conductive oxides (p-type $Cu_2O$ and n-type ZnO) were appliedto form the transparent p/n junction. The functional AZO layer was adopted to improve the transparent photodetector performance between the ZnO and ITO, improving the photoresponses because of its electrical conductivity. To clarify the AZO functionality, a comparator device was prepared without the AZO layer in the formation of $Cu_2O$/ZnO/ITO/Glass. The $Cu_2O$/ZnO/AZO/ITO device provided a rectifying ratio of 113.46, significantly better than the 9.44 of the $Cu_2O$/ZnO/ITO device. In addition, the $Cu_2O$/ZnO/AZO/ITO device's photoresponses at short wavelengths were better than those of the comparator. The functioning AZO layer provides ahigh-performing transparent Cu oxide photodetector and may suggest a route for the design of efficient photoelectric devices.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.296-303
• /
• 2005

The co-pyrolysis characteristics of polyvinylchloride (PVC) and acrylonitrile butadiene styrene (ABS) mixtures with various mixing ratios and effect of addition of CaO and $Cu_2O$ have been studied using thermogravimetry (TG) and gas chromatograph-mass spectrometry (GC-MS). In an isothermal decomposition conducted at $500^{\circ}C$, the yields of styrene monomers and aromatic compounds increased as the mixing ratio of ABS increased, and the yield of BTX compounds reached its maximum (16.14%) when the mixing ratios of PVC and ABS was 4:1. In an isothermal decomposition added with metal oxides, the maximum yield of liquid product was 73% when CaO [CaO/(PVC+ABS)=0.4] was added and it was 70% when $Cu_2O$ [$Cu_2O$/(PVC+ABS)=0.4] was added, respectively, where HCl contained in the gaseous product was completely removed when added with CaO [CaO/(PVC+ABS)=0.5] and $Cu_2O$ [$Cu_2O$/(PVC+ABS)=1.0]. Therefore, to obtain the highest yield of liquid product it appears to be the reaction condition: the reaction temperature of $500^{\circ}C$ and mixing ratios of CaO and $Cu_2O$ are 0.5 and 1.0, respectively.