• Economic and Environmental Geology
• /
• v.46 no.6
• /
• pp.509-520
• /
• 2013

In this study, heavy metals are removed by soil washing from soils contaminated with Cu, Zn, and Pb, whose maximum concentrations are up to 3350, 1220, and 2240 mg/kg, respectively. Through various soil washing experiments, the optimum conditions, including type and concentration of washing reagent, washing time, mixing ratio of soil and washing reagent, and stirring speed, are derived for effective removal of the heavy metals. It is found that the most effective washing reagent and its concentration are hydrochloric acid and 50 mM, respectively. The most suitable washing time is 30 minutes and the optimal mixing ratio of soil and washing reagent is 1:30 (g/mL). The removal efficiency, on the other hand, is not affected by stirring speed. The removal efficiencies of the heavy metals decrease when washing reagent is reused. Furthermore, the heavy metals are readsorbed onto soil in case of consecutive reuse of washing reagent.

• Journal of Environmental Science International
• /
• v.8 no.4
• /
• pp.497-502
• /
• 1999

Removal of Pb(Ⅱ), Cu(Ⅱ), Cr(Ⅲ), and Zn(Ⅱ) ions from aqueous solutions using the adsorption process on domestic loess minerals has been investigated. Variations of contact time, pH, adsorption isotherms and selectivity of coexisting ions and leachate were experimental parameters. YDI, YPT and KRT samples diluted in 1% aquous solution which was adjusted pH 10.8, 8.0 and 6.50, respectively. The result of XRD measurement, Quartz was mainly observed in all samples. In the case of KRT sample, Kaolinite, Feldspar, Chlorite consisting of clay minerals shows almost same pattern with YPT samples. Different properties showed from the YDI sample containing Iillite, remarkably. For all the metals, maximum adsorption was observed at 30min∼60min. Adsorption of metal ions on loess minerals were reached an equilibrium by shaking the solution for about 30min. Removal efficiency of Pb(Ⅱ) ion for KRT, YPT and YDI were 84.7%, 92% and 100%, respectively. The Cu(Ⅱ) and Zn(Ⅱ) adsorptivity on KRT showed the low in various pH solution However, those on YPT and YDI were high than 90% except for the pH 2 solution. The orders of adsorptivities for domestic loess minerals showed as following : YPT>KRT>YDI. The adsorption isotherms of Cu(Ⅱ) and Zn(Ⅱ) ions on clay minerals were fitted to a Freundlich's. Freundlich constants(1/n) of KRT and YPT domestic loess minerals were 0.63, 0.97 and 0.36, 0.25, respectively.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.348-351
• /
• 2012

The effect of the addition of Cu on the catalytic activity of the $Mn/CeO_2-ZrO_2$ catalyst for the low-temperature SCR reaction of NO was investigated. Three different amounts of Cu, 5, 10, and 15 wt%, were impregnated on the $Mn/CeO_2-ZrO_2$ catalyst. The characteristics of the synthesized catalysts were examined by BET, XRD, XPS, and $H_2-TPR$ analyses. The de-NOx efficiency of the Cu-added catalysts increased with the amount of Cu. When 15 wt% Cu was impregnated, the deNOx efficiency was the highest, reaching as high as 99%. The increased deNOx efficiency is attributed to the enhanced reducing power stemming from the interaction between Mn and Cu on the catalyst surface.

• Journal of Korean Society on Water Environment
• /
• v.30 no.6
• /
• pp.647-652
• /
• 2014

The aim of this study was to investigate the heavy metal removal and biomass productivity in the Acid Mine Drainage (AMD) using eggshell and microalgae. The experiment was operated 6 days in the eggshell and microalgae hybrid system, and using eggshell powder and microalgae as Chlorella vulgaris. The obtained result indicated that the biomass productivity of 2.82 g/L/d from 1.12 g/L initial concentration in 6 days was reached with light transmittance of 97% at a 305 mm depth in the optical panel photobioreactor (OPPBR). The total removal efficiency of Fe, Cu, Zn, Mn and Cd was found to be 98.92%, 99.91%, 98.78%, 88.99% and 98.00% in the AMD using eggshell and Chlorella vulgaris hybrid system, respectively. Additionally, there were significant relationships between biomass and concentration of each heavy metal ($R^2$ = 0.8771, 0.8643, 0.8669, 0.9134 and 0.6277 for Fe, Cu, Zn, Mn and Cd). These results indicated that the eggshell and microalgae hybrid system was highly effective for heavy metal removal when compared to the conventional biological process in the AMD. Therefore, the eggshell and microalgae hybrid system was effective for heavy metal removal and biomass productivity and can be applied to treat AMD in treatment plant.

• Journal of Energy Engineering
• /
• v.13 no.2
• /
• pp.133-143
• /
• 2004

Simultaneous removal technology of particulate/NOx/SOx/HCl using CuO/3Al$_2$O$_3$ㆍ2SiO$_2$catalyst impregnated ceramic candle filters is an advanced air pollution process and provides significantly to reduce hazardous gases emitted from coal-fired power plant. This process uses a high-temperature catalytic filter for integrating SOx and HCl reduction through injection an alkali sorbent (such as hydrated lime or sodium bicarbonate), NOx removal through ammonia injection and selective catalytic reduction (SCR), and particulate collection on the catalytic filter surface. The advantages of the process include : compact integration of the emission control technologies into a single component; easy handling of dry sorbent and by-product; and improved SCR catalytic life due to lowered SOx, HCl and particulate levels. CuO/3Al$_2$O$_3$ㆍ2SiO$_2$ catalyst impregnated ceramic candle filters showed a possibility of simultaneous treatment from results which have ascertained high removal efficiency at various combined gases conditions, and in pilot plant test for 3 months, NO conversion was showed 90% over.

• Mycobiology
• /
• v.49 no.5
• /
• pp.507-520
• /
• 2021

Papiliotrema huenov was previously reported to be highly tolerant of a range of extremely toxic heavy metals. This study aimed to identify the potential of P. huenov to remove manganese and copper from aqueous solution. Physical conditions which affect removal of Mn(II) and Cu(II) were determined. Optimal temperature for adsorption of both metal ions was 30 ℃, and optimal pH for maximum uptake of Mn(II) and Cu(II) were 5 and 6, respectively. Under these conditions, living cells of P. huenov accumulated up to 75.58% of 110 mg/L Mn(II) and 70.5% of 128 mg/L Cu(II) over 120 h, whereas, the removal efficiency of metal ions by dead cells over 1 h was 60.3% and 56.5%, respectively. These results indicate that living cells are more effective than dead biomass for bioremediation, but that greater time is required. The experimental data extends the potential use of P. huenov in biosorption and bioaccumulation of toxic heavy metals to copper and manganese, two of the most common industrial contaminants.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.441-448
• /
• 2016

Heavy metal removal study is conducted from synthetic waste water by reduction and oxidation(redox) reaction of Cu-Zn metal alloy and adsorption reaction of aluminium silicate. Heavy metal whose ionization tendency is smaller than zinc are reducted in an aqueous solution, and the concentration of ionized zinc is reduced by adsorption reaction. The average diameter of metal alloy micro fiber is about $200{\mu}m$, and the surface area is wide enough to get equilibrium in a single cycle treatment. A single cycle treatment of redox reaction of Cu-Zn metal alloy, could remove 100.0 % of Cr(III), 98.0 % of Hg, 92.0 % of Sn and 91.4 % of Cu respectively. An ionization tendency of chromium is very close to zinc, but removal efficiency of chromium by redox reaction is significant. This result shows that trivalent chromium ion is expected to generate hydroxide precipitation with $OH^-$ ion generated by redox reaction. Zinc ion generated by redox reaction is readily removed by adsorption reaction of aluminium silicate in a single cycle treatment. Other heavy metal components which are not perfectly removed by redox reaction also showed very high removal efficiency of 98.0 % or more by adsorption reaction. Aluminium ion is not increased by adsorption reaction of aluminium silicate. That means heavy metal ion removal mechanism by adsorption reaction is turned out to be not an ion exchange reaction, but an adsorption reaction.

• Journal of Environmental Science International
• /
• v.30 no.11
• /
• pp.945-956
• /
• 2021

In this study, the effects of single and binary heavy metals toxicity on the growth and phosphorus removal ability of Bacillus sp.. known as be a phosphorus-removing microorganism, were quantitatively evaluated. Cd, Cu, Zn, Pb, Ni were used as heavy metals. As a result of analysis of variance of the half of inhibition concentration and half of effective concentration for each single heavy metal treatment group, the inhibitory effect on the growth of Bacillus sp. was Ni < Pb < Zn < Cu < Cd. And the inhibitory effect on phosphorus removal by Bacillus sp. was Ni < Pb < Zn < Cu < Cd. When analyzing the correlation between growth inhibition and phosphorus removal efficiency of a single heavy metal treatment group, a negative correlation was found (R² = 0.815), and a positive correlation was found when the correlation between IC₅₀ and EC₅₀ was analyzed (R² = 0.959). In all binary heavy metal treatment groups, the interaction was an antagonistic effect when evaluated using the additive toxicity index method. This paper is considered to be basic data on the toxic effects of heavy metals when phosphorus is removed using phosphorus removal microorganisms in wastewater.

• Korean Journal of Materials Research
• /
• v.8 no.9
• /
• pp.837-842
• /
• 1998

As the size of the integrated circuit is scaled down the importance of Si cleaning has been emphasized. One of the major concerns is abut the removal of metallic impurities such as Cu and Fe on Si surface. In this study, we intentionally contaminated Cu and Fe on the Si wafers and cleaned the wafer by cleaning splits of the chemical mixture of $\textrm{H}_2\textrm{O}_2$ and HF and the combination of HF treatment with UV/$\textrm{O}_3$ treatment. The contamination level was monitored by TXRF. Surface microroughness of the Si wafers was measured by AFM. The Si wafer surface was examined by SEM. AES analysis was carried out to analyze the chemical composition of Cu impurities. The amount of Cu impurities after intentional contamination was abut the level of $\textrm{10}^{14}$ atoms/$\textrm{cm}^2$. The amount of Cu was decreased down to the level of $\textrm{10}^{10}$ atoms/$\textrm{cm}^2$ by cleaning splits. The repeated treatment exhibited better Cu removal efficiency. The surface roughness caused by contamination and removal of Cu was improved by repeated treatment of the cleaning splits. Cu were adsorbed on Si surface not in a thin film type but in a particle type and its diameter was abut 100-400${\AA}$ and its height was 30-100${\AA}$. Cu was contaminated on Si surface by chemical adsorption. In the case of Fe the contamination level was $\textrm{10}^{13}$ atoms/$\textrm{cm}^2$ and showed similar results of above Cu cleaning. Fe was contaminated on Si surface by physical adsorption and as a particle type.

• Resources Recycling
• /
• v.30 no.2
• /
• pp.68-74
• /
• 2021

This study investigated formaldehyde (HCHO) removal by preparing porous supports using domestic low-grade silica coated with Co-ZSM5 and Cu-ZSM5 as the catalysts. First, the sample of the raw material for the support contained 90% silica with quartz crystal phase, which was confirmed as low-grade silica. According to Energy-dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FT-IR) analyses, the catalysts, Co-ZSM5 and Cu-ZSM5, were successfully coated on the surface of the porous silica supports. During the removal test of HCHO using the prepared Co-ZSM5 and Cu-ZSM5 coated beads, depending on the reaction temperature, the Co-ZSM5 coated beads exhibited higher removal efficiencies (>97%) than the Cu-ZSM5 beads at 200 ℃. The higher efficiency of the Co-ZSM5 coating may be attributed to its superior surface activity properties (BET surface area and pore volume) that lead to the favorable HCHO decomposition. Therefore, Co-ZSM5 was determined to be the suitable catalyst for removing HCHO as a coating on a porous support fabricated using domestic low-grade silica.