• Korean Chemical Engineering Research
• /
• 제61권1호
• /
• pp.52-57
• /
• 2023

본 연구는 고성능 유연 전극 소재 개발을 위한 기초 연구로, 유연 전극 소재의 성능을 향상시키기 위해 금속 산화물 CuO nanoparticles (CuO NPs)를 도입하여 탄소나노튜브 섬유(carbon nanotube fiber; CNT fiber) 표면 위에 전기화학적 증착시켜 CNT fiber/CuO NPs 전극을 합성하고, 이를 전기화학적 비효소 글루코스 센서에 적용하였다. 이 전극의 표면 및 elemental composition 분석은 주사전자 현미경(SEM)과 에너지분산형 분광분석법(EDS)을 이용하였으며, 전극의 전기화학적 특성 및 글루코스에 대한 센싱 성능은 순환전압 전류법(CV)과 전기화학 임피던스법(EIS), 시간대전류법(CA)을 통해 조사되었다. CNT fiber/CuO NPs 전극은 CNT fiber의 우수한 특성과 함께 CuO NPs 도입에 따른 약 2.6배의 유효 전극면적(active surface area) 증가 효과와 11배 정도의 향상된 전자전달(electron transfer) 특성 및 우수한 전기적 촉매 활성(electrocatalytic activity) 덕분에 CNT fiber 유연 기반 전극의 글루코스 검출에 대한 성능이 개선되었다. 따라서, 본 연구를 기반으로 다양한 나노구조체를 활용한 고성능 유연 전극 소재 개발이 기대된다.

• Korean Chemical Engineering Research
• /
• 제61권2호
• /
• pp.196-201
• /
• 2023

우리는 금속 산화물 CuO nanoparticles (CuO NPs)과 전도성 고분자 Polyaniline (PANI)가 접목된 CNT fiber 유연 전극(CuO NPs/PANI/CNT fiber 전극)을 개발하여 H₂O₂ 검출용 비효소적 전기화학센서에 적용하였다. CNT fiber 표면 위에 PANI와 CuO NPs을 전기화학적 합성/증착을 통해 제작된 CuO NPs/PANI/CNT fiber 전극은 주사전자 현미경(SEM)과 에너지분산형 분광분석법(EDS)을 통해 표면 분석이 수행되었으며, 순환전압 전류법(CV)과 전기화학 임피던스법(EIS), 시간대전류법(CA)을 이용하여 전기화학적 특성 및 H₂O₂ 센싱 성능이 분석되었다. CuO NPs/PANI/CNT fiber 전극은 대조군인 bare CNT fiber 전극과 비교하여 약 4.78배의 유효 표면적 증가를 보였으며, 약 8.33배의 전자 전달 저항(R_et) 감소로 인한 우수한 전기 전도성 및 효율적인 전자전달 등의 전기화학적 특성을 나타냈다. 이런 향상된 전극 특성은 CuO NPs와 PANI의 접목을 통한 시너지 효과에 기인한 것으로, 결과적으로 H₂O₂ 검출에 대한 센싱 성능이 개선되었다.

• Bulletin of the Korean Chemical Society
• /
• 제35권8호
• /
• pp.2431-2437
• /
• 2014

In this study, Ni, Ni-Cu and Ni/Cu catalysts were deposited onto C-fiber textiles via the electrophoretic deposition method, and the growth characteristics of carbon nanofibers on the deposited catalyst/C-fiber textiles were investigated. The catalyst deposition onto C-fiber textiles was accomplished by immersing the C-fiber textiles into Ni or Ni-Cu mixed solutions, producing the substrate by post-deposition of Ni onto C-fiber textiles with pre-deposited Cu, and passing it through a gas mixture of $N_2$, $H_2$ and $C_2H_4$ at $700^{\circ}C$ to synthesize carbon nanofibers. For analysis of the characteristics of the synthesized carbon nanofibers and the deposition pattern of catalysts, SEM, EDS, BET, XRD, Raman and XPS analysis were conducted. It was found that the amount of catalyst deposited and the ratio of Ni deposition in the Ni-Cu mixed solution increased with an increasing voltage for electrophoretic deposition. In the case of post-deposition of Ni catalyst onto substrates with pre-deposited Cu, both bimetallic catalyst and carbon nanofibers with a high level of crystallizability were produced. Carbon nanofibers yielded with the catalyst prepared in Ni and Ni-Cu mixed solutions showed a Y-shaped morphology.

• 한국재료학회지
• /
• 제31권11호
• /
• pp.626-634
• /
• 2021

Cu matrix composites reinforced with chopped carbon fiber (CF), which is cost effective and can be well dispersed, are fabricated using electroless plating and hot pressing, and the effects of content and alignment of CF on the thermal properties of CF/Cu composites are studied. Thermal conductivity of CF/Cu composite increases with CF content in the in-plane direction, but it decreases above 10% CF; this is due to reduction of thermal diffusivity related with phonon scattering by agglomeration of CF. The coefficient of thermal expansion decreases in the in-plane direction and increases in the through-plane direction as the CF content increases. This is because the coefficient of thermal expansion of the long axis of CF is smaller than that of the Cu matrix, and the coefficient of thermal expansion of its short axis is larger than that of the Cu matrix. The thermal conductivity is greatly influenced by the agglomeration of CF in the CF/Cu composite, whereas the coefficient of thermal expansion is more influenced by the alignment of CF than the aggregation of CF.

• 한국결정학회지
• /
• 제7권2호
• /
• pp.147-155
• /
• 1996

할로겐 램프를 열원으로 이용하는 결정성장장치인 부유대역융로를 제작하여 고온초전도체 Bi2Sr2CaCu2O8의 성장에 이용하였다. 제작된 결정성장장치는 할로겐 램프를 초점에 위치시키기 위한 holder unit, 1kW의 할로겐 램프로서 최대 1800℃까지 사용이 가능한 image furnace, 냉각장치, 원료 물질을 공급하는 feeding unit, 성장된 단결정을 인상하는 pulling unit, 그리고 2mm/hr - 40mm/hr의 속도로 상하 이동 및 15rpm -120rpm의 회전이 가능한 제어부 등으로 구성되었다. 300W의 할로겐 램프를 이용하여 Bi2Sr2CaCu2O8 fiber를 성장시켰으며 성장된 fiber는 XRD, SEM, EDS 등으로 분석하였다. 성장조건은 공기분위기에서 성장속도 3∼4mm/hr, 상·하부축 회전속도 20∼25 rpm이었으며 성장된 fiber는 Bi2Sr2CaCu2O8 기지 내에 (Sr,Ca)CuO2 및 (Sr,Ca)2CuO3의 2차상을 포함하고 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제32권7호
• /
• pp.2351-2357
• /
• 2011

Three new metal-organic copper(II) complexes, $[Cu(H_2PZTC)_2]_n{\cdot}2nH_2O$ (1), $[Cu(HPZTC){\cdot}2H_2O]_n{\cdot}2nH_2O$ (2), and $Cu_2[(PZHD)(OH)(H_2O)_2]_n$ (3) ($H_3PZTC$ = pyrazine-2,3,5-tricarboxylic acid, $PZHD^{3-}$ = 2-hydroxypyrazine-3,5-dicarboxylate), have been synthesized from $Cu(II)/H_3PZTC$ system under different synthetic conditions, and characterized by single-crystal X-ray diffraction, elemental analysis, IR spectroscopy and thermogravimetric analysis. In complexes 1 and 2, $H_3PZTC$ ligands loose one and two protons, which were transformed into $H_2PZTC^-$ anion and $HPZTC^{2-}$ dianion under different preparation condition, respectively. Furthermore, two ligands coordinate with Cu(II) cations in different modes, leading to the formation of the different chain structures. In complex 3, $H_3PZTC$ ligand was converted into a new ligand-PZHD by in situ decarboxylation and hydroxylation under a higher pH value than that for complexes 1 and 2. PZHD ligands link the Cu(II) cations to form a 2D layer structure. These results demonstrate that the preparation conditions, including pH value and reaction temperature etc, play an important role in the construction of complexes based on $H_3PZTC$ ligand.

• 한국염색가공학회지
• /
• 제11권4호
• /
• pp.8-15
• /
• 1999

Electroconductive fiber was obtained by acryl fiber treated with $CuSO_4$. The Properties and structure of fiber and fabric such as mechanical property, electrical conductivity, fine structure, electrification were investigated. The experimental results are as follows 1) The electrical conductivity of the conducting fiber was greatly increased but fine structure and physical properties were similar to acryl fiber 2) Fabric made by mix spinning with conducting fiber was shown great electrification effect. 3) In the mix spinning with conducting fiber, it was necessary to use different. finishing such as milled finish because stiffness of fabric made by mix spinning with conducting fiber was increased and elastic recovery was decreased. 4) The antimicrobial activity of electroconductive fiber blended wool was effective by Cu component for shake flask test.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.56-63
• /
• 2014

To develop and understand dissimilar metals joining of Stainless steel and Copper, ultra-high speed laser lap welding was studied using single mode fiber laser in this study. SUS304 and Cu have large differences in materials properties, and Cu and Fe have no intermetallic compounds by typical binary phase of Cu and Fe system. In this study, ultra-high speed lap welds of SUS304 and Cu dissimilar metals using single-mode fiber laser was generated, and weldability of the weld fusion zone was evaluated using a tensile shear test. To understand the phenomenon of tensile shear load, weld fusion zone of interface weld area and fracture parts after tensile shear test were observed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analysis system. And it was confirmed that Cu was easily melting and penetrating in the grain boundaries of SUS304 because of low melting temperature. And high thermal conductivity of copper occurred dissipate heat energy rapidly. These properties cause the solidification cracking in weld zone.

• 한국전기전자재료학회논문지
• /
• 제34권2호
• /
• pp.105-109
• /
• 2021

CNT fiber has been in the spotlight as a conductor, but the conductivity of CNT fibers do not match that of CNT. This study reveals that the conductivity of CNT fiber can be improved by depositing Al/Cu through vacuum evaporation. Cu is commonly used for deposition on CNT fibers. But low bonding strength of the interface between CNT and Cu could be a disadvantage. To overcome this, Al was deposited on the CNT fiber for forming aluminum carbide islands to increase the interfacial bonding strength. The conductivity characteristics were improved as the deposition time increased. The resistance was measured as a function of temperature, demonstrating that the temperature coefficient of resistance (TCR) is improved to be 241 ppm/℃ in comparison with that of as-received CNT fibers at -1,251 ppm/℃, when the CNT fibers are deposited with Al and Cu, respectively, for 90s and for 540s.

• 한국분말재료학회지
• /
• 제25권1호
• /
• pp.30-35
• /
• 2018

The friction characteristics of Al-Fe alloy powders are investigated in order to develop an eco-friendly friction material to replace Cu fiber, a constituent of brake-pad friction materials. Irregularly shaped Al-Fe alloy powders, prepared by gas atomization, are more uniformly dispersed than conventional Cu fiber on the brake pad matrix. The wear rate of the friction material using Al-8Fe alloy powder is lower than that of the Cu fiber material. The change in friction coefficient according to the friction lap times is 7.2% for the Cu fiber, but within 3.8% for the Al-Fe alloy material, which also shows excellent judder characteristics. The Al-Fe alloy powders are uniformly distributed in the brake pad matrix and oxide films of Al and Fe are homogeneously formed at the friction interface between the disc and pad, thus exhibiting excellent friction and lubrication characteristics. The brake pad containing Al-Fe powders avoids contamination by Cu dust, which is generated during braking, by replacing the Cu fiber while maintaining the friction and lubrication performance.