For the aerospace structural application of high-strength 2xxx series aluminum alloys, stress corrosion cracking(SCC) behavior in aggressive environments needs to be well understood. In this study, the SCC sensitivities of 2024-T62, 2124-T851 and 2050-T84 alloys in a 3.5 % NaCl solution are measured using a constant load testing method without polarization and a slow strain rate test(SSRT) method at a strain rate of 10-6 /sec under a cathodic applied potential. When the specimens are exposed to a 3.5 % NaCl solution under a constant load for 10 days, the decrease in tensile ductility is negligible for 2124-T851 and 2050-T84 specimens, proving that T8 heat treatment is beneficial in improving the SCC resistance of 2xxx series aluminum alloys. The specimens are also susceptible to SCC in a hydrogen-generating environment at a slow strain rate of $10^{-6}/sec$ in a 3.5 % NaCl solution under a cathodic applied potential. Regardless of the test method, low impurity 2124-T851 and high Cu/Mg ratio 2050-T84 alloys are found to have relatively lower SCC sensitivity than 2024-T62. The SCC behavior of 2xxx series aluminum alloys in the 3.5 % NaCl solution is discussed based on fractographic and micrographic observations.
Sm-Co소결자석의 자기적 특성에 미치는 Zr의 영향을 연구하기 위해 Zr함량별로 잉곳을 제조하여 용체화처리 및 시효 조건에 따른 소결자석의 미세구조와 자기적 특성을 조사하였다. Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ (0.013$\leq$x$\leq$0.026) 합금의 주조조직은 x가 증가함에 따라 공정조직의 분율이 작아지고 공정 영역의 크기가 감소하였다. 반면, 수지상 조직은 x=0.022합금이 가장 미세하였다. Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ 소결자석은 Sm $Co_{5}$상과 S $m_2$C $O_{17}$상으로 이루어진 셀 구조를 형성하며 셀 경계상인 Sm $Co_{5}$상의 두께는 20nm이고 120$^{\circ}$의 각을 갖고 형성되었다. 또한, Zr 함량이 증가함에 따라 셀 크기가 감소하였다. 그러나 x=0.026 합금은 셀 경계가 분명하게 정의되지 않고 셀 형태가 x=0.022합금에 비해 불규칙하였다. 이러한 미세조직 차이로 인해 x=0.022 합금의 자기적 특성이 가장 높았다. Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ 합금의 최적 용체화처리온도는 117$0^{\circ}C$였고, 보자력 향상을 위한 2단시효 공정중 최적의 1단 시효 온도는 85$0^{\circ}C$였다.
The objective of this study was to analyze the in vitro and in vivo corrosion products of low and high copper amalgams. The four different types of amalgam alloy used in this study were Fine cut, Caulk spherical, Dispersalloy, and Tytin. After each amalgam alloy and Hg were triturated according to the directions of the manufacturer by means of the mechanical amalgamator(Amalgam mixer. Shinhung Co. Korea), the triturated mass was inserted into a cylindrical metal mold which was 12mm in diameter and 10mm in height. The mass was condensed by 150Kg/cm compressive force. The specimen was removed from the mold and aged at room temperature for about seven days. The standard surface preparation was routinely carried out by emery paper polishing under running water. In vitro amalgam specimens were potentiostatically polarized ten times in a normal saline solution at $37^{\circ}C$(potentiostat : HA-301. Hukuto Denko Corp. Japan). Each specimen was subjected to anodic polarization scan within the potential range -1700mV to+400mV(SCE). After corrosion tests, anodic polarization curves and corrosion potentials were obtained. The amount of component elements dissolved from amalgams into solution was measured three times by ICP AES(Inductive Coupled Plasma Atomic Emission Spectrometry: Plasma 40. Perkim Elmer Co. U.S.A.). The four different types of amalgam were filled in occlusal and buccal class I cavities of four human 3rd molars. After about five years the restorations were carefully removed after tooth extraction to preserve the structural details including the deteriorated margins. The occlusal surface, amalgam-tooth interface and the fractured surface of in vivo amalgam corrosion products were analyzed. In vivo and in vitro amalgam specimens were examined and analyzed metallographically by SEM(Scanning Electron Microscope: JSM 840. Jeol Co. Japan) and EDAX(Energy Dispersive Micro X-ray Analyser: JSM 840. Jeol Co. Japan). 1. The following results are obtained from in vitro corrosion tests. 1) Corrosion potentials of all amalgams became more noble after ten times passing through the in vitro corrosion test compared to first time. 2) After times through the test, released Cu concentration in saline solution was almost equal but highest in Fine cut. Ag and Hg ion concentration was highest in Caulk spherical and Sn was highest in Dispersalloy. 3) Analyses of surface corrosion products in vitro reveal the following results. a)The corroded surface of Caulk spherical has Na-Sn-Cl containing clusters of $5{\mu}m$ needle-like crystals and oval shapes of Sn-Cl phase, polyhedral Sn oxide phase. b)In Fine cut, there appeared to be a large Sn containing phase, surrounded by many Cu-Sn phases of $1{\mu}m$ granular shapes. c)Dispersalloy was covered by a thick reticular layer which contained Zn-Cl phase. d)In Tytin, a very thin, corroded layer had formed with irregularly growing Sn-Cl phases that looked like a stack of plates. 2. The following results are obtained by an analysis of in vivo amalgam corrosion products. 1) Occlusal surfaces of all amalgams were covered by thick amorphous layers containing Ca-P elements which were abraded by occlusal force. 2) In tooth-amalgam interface, Ca-P containing products were examined in all amalgams but were most clearly seen in low copper amalgams. 3) Sn oxide appeared as a polyhedral shape in internal space in Caulk spherical and Fine cut. 4) Apical pyramidal shaped Sn oxide and curved plate-like Sn-Cl phases resulted in Dispersalloy. 5) In Tytin, Sn oxide and Sn hydroxide were not seen but polyhedral Ag-Hg phase crystal appeared in internal space which assumed a ${\beta}_l$ phase.
상온과 액체질소온도에서 압축시험을 통하여 $LI_{2}$단상함금 및 $LI_{2}$상에 제 2상을 수 %또는 20%정도 포함하는 합금조성을 선택하였다. 일반적으로 제 2상을 20%정도 포함하는 2상합금들은 $Ll_{2}$단상합금에 비해 항복강도는 높으나 연성은 좋지 않았다. 그러나 $Cr_{2}AI$을 제 2상으로하는 20%정도 포함하는 Al-21Ti-23Cr합금은 다른 합금들에 비해 비교적 높은 항복강도와 함계 우수한 연성을 나타내었다. 또한 $Li_{2}$단상합금 및 $Cr_{2}Al$을 수% 포함하는 2상합금에 대한 소성거동도 조사하였다. 균질화처리 후에 제 2상의 양은 줄었으나 pore의 양은 증가하였다. 균질화처리 후에 $Ll_{2}$단상조직에서 나타나는 pore의 양은 Cr의양이 증가할수록 줄어들었으며, Cr 의 양이 더욱 증가하여 $Cr_{2}$Al이 제2상으로 생성될 때는 pore가 완전히 소멸하였다. 변형속도를 $1.2 \times 10^{-4}/s$와 $1.2 \times 10^{-2}/s$의 두가지 조건으로 변화시키면서 압축시험을 행하여 합금의 연성에 미치는 환경취성의 영향을 조사하였다. $LI_{2}$단상합금인 AI-25Ti-10Cr합금이 환경취성의 영향을 가장 적게 받는 것으로 나타났다. 그러나 pore의 생성, 환경취성, ingot 주조조직 등을 종합평가해 보면 $Cu_{2}Al$을 제 2상으로 20%정도 포함하는 Ak-21Ti-23Cr합금이 가장 우수한 인장연싱율을 나타낼 것으로 기대된다.
완구(碗口)란 유통식 화기로 발사체 장전 부분이 사발(碗) 형태인 화포이다. 발사체로는 비격진천뢰(飛擊震天雷)나 단석(團石) 등을 사용하였다. 『화포식언해(火砲式諺解)』(이서(李曙), 1635)에 의하면, 대·중·소·소소완구 등 총 4종으로 구분되며, 실물은 대완구 1점(보물 제857호), 중완구 2점(보물 제858호, 제859호) 등 총 3점이 전한다. 본 연구에서는 임진왜란기에 제작된 국립진주박물관 소장 중완구(보물 제858호)와 해군사관학교 박물관 소장 중완구(보물 제859호)의 과학적 조사를 토대로 제작 기술을 확인하였다. 첫 번째로 국내 현전하는 중완구가 단 두점인 만큼 정밀 3D 스캐닝 정보를 바탕으로 세부 제원을 서로 비교하고, 동 시기의 문헌 기록 수치와 함께 검토하였다. 전체 크기차는 근소하나 중량에서 5,507g의 차이를 보이고, 세부적으로 심지구멍 위치와 손잡이 길이가 상이하다. 한편 현전 중완구는 『화포식언해』의 중완구 제원과 가장 유사하다. 두 번째로는 중완구의 성분을 분석하고 기존 청동제 화약 무기와 함께 검토하였다. 표면 성분 분석결과, 중완구는 Cu-Sn-Pb의 삼원계 합금이며, 평균 함량(wt%)은 Cu 85.24 : Sn 10.16 : Pb 2.98이다. 중완구의 재료 성분은 기존에 조사된 조선 청동 화약 무기의 평균 성분과 매우 유사하며, 중세 유럽의 청동제 화포 재료(Gun-metal)와도 유사한 경향임을 확인하였다. 마지막으로 중완구 표면의 주조 결함(casting defect)과 CT 상을 토대로 주조 기법을 추정하였다. 측면의 주조분할선으로 보아 주형을 반으로 나눈 분할 제작(piece mold)이며, 용탕의 주입은 약실끝 부분으로 포구가 바닥에 오는 수직 주형 설계로 추정한다. 특히 포신 기벽에서 주형과 코어를 고정하는 보조 장치인 채플릿(chaplets)이 확인되므로 이는 기벽을 일정하게 형성하는 역할을 했을 것이다. 한편 보물 제858호와 제859호 중완구 두 점은 외형이 매우 유사하지만, 채플릿의 수량과 배치가 상이하여 주형 설계 일부가 달랐을 것으로 예상한다.
경사진 빗살무늬 변환기 필터를 제작하기 위하여 Langasite 기판위에 두 가지 형태의 빗살무늬 변환기를 형성시켰으며, 전극재료로는 Al-Cu를 사용하였다. 모의실험을 바탕으로 입력단에는 IDT를 직렬형태로 연결시킨 block 형태로 하중을 가하는 전극 방법을 쓰고 출력단은 withdrawal 형태로 하중을 가하는 방법을 써서 제작하였다. 이를 바탕으로 경사진 빗살무늬 변환기 필터 전극 설계 방식에 대한 적절한 위상조건도 얻고자 시도하였다. Langasite 기판위에 형성시킨 입출력 빗살무늬 변환기 전극수는 50쌍, 두께는 $5000\;{\AA}$으로 하였으며, 반사기 폭은 $3.6{\mu}m$으로 하였다. 첫 번째 시료에서 hot전극과 반사기사이의 거리는 $2.4{\mu}m$이고, 접지 전극과 반사기사이의 거리는 $1.8{\mu}m$이며, hot전극에서부터 접지전극까지 간격은 $1.5{\mu}m$로 제작하였다. 두 번째 시료는 hot전극과 반사기사이의 거리 및 접지 전극과 반사가사이의 거리를 $2.4{\mu}m$로 동일하게 제작하였다. 제작한 필터의 주파수 특성은 중심주파수가 대략 190MHz정도, 대역폭은 7.3MHz이하로 측정되었으며, matching 후 return loss는 -20dB 이하이고, 리플 특성은 3dB정도이며, 반사에 의한 잔향은 -22dB 이하로 측정되었다.
The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.
The most important industrial application of gamma radiation in characterizing green compacts is the determination of the density. Examples are given where this method is applied in manufacturing technical components in powder metallurgy. The requirements imposed by modern quality management systems and operation by the workforce in industrial production are described. The accuracy of measurement achieved with this method is demonstrated and a comparison is given with other test methods to measure the density. The advantages and limitations of gamma ray densitometry are outlined. The gamma ray densitometer measures the attenuation of gamma radiation penetrating the test parts (Fig. 1). As the capability of compacts to absorb this type of radiation depends on their density, the attenuation of gamma radiation can serve as a measure of the density. The volume of the part being tested is defined by the size of the aperture screeniing out the radiation. It is a channel with the cross section of the aperture whose length is the height of the test part. The intensity of the radiation identified by the detector is the quantity used to determine the material density. Gamma ray densitometry can equally be performed on green compacts as well as on sintered components. Neither special preparation of test parts nor skilled personnel is required to perform the measurement; neither liquids nor other harmful substances are involved. When parts are exhibiting local density variations, which is normally the case in powder compaction, sectional densities can be determined in different parts of the sample without cutting it into pieces. The test is non-destructive, i.e. the parts can still be used after the measurement and do not have to be scrapped. The measurement is controlled by a special PC based software. All results are available for further processing by in-house quality documentation and supervision of measurements. Tool setting for multi-level components can be much improved by using this test method. When a densitometer is installed on the press shop floor, it can be operated by the tool setter himself. Then he can return to the press and immediately implement the corrections. Transfer of sample parts to the lab for density testing can be eliminated and results for the correction of tool settings are more readily available. This helps to reduce the time required for tool setting and clearly improves the productivity of powder presses. The range of materials where this method can be successfully applied covers almost the entire periodic system of the elements. It reaches from the light elements such as graphite via light metals (AI, Mg, Li, Ti) and their alloys, ceramics ($AI_20_3$, SiC, Si_3N_4, $Zr0_2$, ...), magnetic materials (hard and soft ferrites, AlNiCo, Nd-Fe-B, ...), metals including iron and alloy steels, Cu, Ni and Co based alloys to refractory and heavy metals (W, Mo, ...) as well as hardmetals. The gamma radiation required for the measurement is generated by radioactive sources which are produced by nuclear technology. These nuclear materials are safely encapsulated in stainless steel capsules so that no radioactive material can escape from the protective shielding container. The gamma ray densitometer is subject to the strict regulations for the use of radioactive materials. The radiation shield is so effective that there is no elevation of the natural radiation level outside the instrument. Personal dosimetry by the operating personnel is not required. Even in case of malfunction, loss of power and incorrect operation, the escape of gamma radiation from the instrument is positively prevented.
공공 예술 조각품과 야외 조형물에 대한 관심과 함께 미술품 보존 관리의 중요성이 높아지고 있다. 야외 조각작품의 경우, 장기간 대기 중에 노출되어 대기오염물과 자연재해 등의 이유로 부식과 열화 등의 손상이 발생하게 되는데, 국립현대미술관 야외조각공원에 전시중인 김찬식의 '정' 역시 부식으로 인해 작품표면의 파티나층이 손상되었다. 따라서 상태조사, 표면연마, 재파티네이션, 왁스코팅 등의 보존처리를 진행하였으며, 그 결과 원형에 가까운 복원을 이룰 수 있었다. 작품의 재질특성에 대한 분석 결과, 구리, 주석, 아연, 납으로 주조된 미술 공예용 청동임을 확인하였다. 작품 표면연마 후 관찰되는 용접, 균열, 밝은 얼룩의 재질 특성 중, 용접부위는 바탕금속보다 구리를 제외한 나머지 주요원소의 함량이 비교적 적은 경향을 보였으며, 밝은 얼룩은 주석과 납의 함량이 13.0 wt%, 10.5 wt%로 바탕금속(주석: 7.0 wt%, 납: 4.4wt%)보다 높게 측정되었다. 또한 미세조직 관찰결과, 작품의 제작은 열처리를 비롯한 인위적인 가공이 가해지지 않은 주조기법이 사용된 것으로 추정되었다.
이 연구는 부여 쌍북리유적에서 출토된 도가니 내부 유리 및 청동용융물질과 금동보살입상의 재료학적 특성 및 고고과학적 상관관계를 규명한 것이다. 도가니 내부의 유리질 용융물질은 주로 황록색과 적갈색을 띠는 PbO-$SiO_2$계의 납유리로서 바륨과 안정제의 함량이 낮은 특징이 있다. 금속용융물질은 Cu, Sn, Pb의 합금으로 이루어진 청동으로 밝혀졌으며, 낮은 불순물 함량으로 미루어 고순도로 정련된 구리를 이용하여 제작되었음을 알 수 있다. 주석의 원광석으로는 석석이 이용된 것으로 판단된다. 금동보살입상의 청동소지도 구리의 함량이 높고 불순물의 함량이 낮아 고도로 정련된 원료를 사용하였으며, 쌍북리 유적의 공방에서 숙련된 기술을 바탕으로 제작되었을 가능성이 충분하다. 또한 표면에는 고순도의 금을 아말감기법으로 도금한 것으로 밝혀졌다. 한편 도가니 내 납유리와 청동물질 및 금동보살입상의 납동위원소비는 일관된 결과를 보여주지 않는 것으로 보아 납광석의 원산지 해석에는 무리가 있는 것으로 판단된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.