• The Journal of Advanced Prosthodontics
• /
• v.9 no.6
• /
• pp.416-422
• /
• 2017

PURPOSE. To investigate the effect of reducing tooth preparation and ceramic thickness on fracture resistance of lithium disilicate crowns. MATERIALS AND METHODS. Specimen preparation included a standard complete crown preparation of a typodont mandibular left first molar with an occlusal reduction of 2 mm, proximal/axial wall reduction of 1.5 mm, and 1.0 mm deep chamfer (Group A). Another typodont mandibular first molar was prepared with less tooth reduction: 1 mm occlusal and proximal/axial wall reduction and 0.8 mm chamfer (Group B). Twenty crowns were milled from each preparation corresponding to control group (n=5) and conditioned group of simultaneous thermal and mechanical loading in aqueous environment (n=15). All crowns were then loaded until fracture to determine the fracture load. RESULTS. The mean (SD) fracture load values (in Newton) for Group A were 2340 (83) and 2149 (649), and for Group B, 1752 (134) and 1054 (249) without and with fatigue, respectively. Reducing tooth preparation thickness significantly decreased fracture load of the crowns at baseline and after fatigue application. After fatigue, the mean fracture load statistically significantly decreased (P<.001) in Group B; however, it was not affected (P>.05) in Group A. CONCLUSION. Reducing the amount of tooth preparation by 0.5 mm on the occlusal and proximal/axial wall with a 0.8 mm chamfer significantly reduced fracture load of the restoration. Tooth reduction required for lithium disilicate crowns is a crucial factor for a long-term successful application of this all-ceramic system.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.4
• /
• pp.77-85
• /
• 1999

In this study, a computer program considering initial imperfection of axisymmetric reinforced concrete shell which plastic deformation by large external loading was developed . Initial imperfection of dome was assumed as 'dimple type' which can be expressed as Wi=(Wo/h)(1-x$^2$)$^3$. The developed model applied to the analysis of dynamic response of axisymmetric reinforced concrete shell when it has initial imperfection. The initial imperfection of 0.0, -5.0, and 5cm and steel and steel layer ratio 0,3, and 5% were tested for numerical examples . The results can be summarized as follows ; 1. Dynmaic response of vertical deflection at dome crown showed slow increased if it has not inital imperfection . But the response showed relatively high amplitude when initial imperfection was inner directed (opposite direction to loading). Similar trends also appeared for different steel layer ratios. 2. Dynamic responses of radial displacement at the junction of dome and wall showed the highest amplitude when initial imperfection was inward directed (opposite direction to loading). The lowest amplitude occurred when initial imperfection was outward directed (same direction to loading). Vibration period also delayed for inward directed initial imperfection . These trends were obvious as steel layer ratio increasing. 3. The effects of imperfection for the dynamic response of radial displacement a the center of wall scarely appeared. The effects of initial imperfection of dome on the dynmaic response of the wall can be neglected. 4. Effect of steel on the dynmic response of axisymmetric shell structure was great when initial imperfection did not exist. And the effect of direction of initial imperfection (inward or outward) did not show big difference.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.4
• /
• pp.119-127
• /
• 2022

To investigate varying wave impact pressure exerting at the crest wall of rubble mound seawall, depending on breaking wave properties, regular waves with different wave periods were generated. Wave velocity fields and void fraction were measured using bubble image velocimetry and simple combined wave gauge system (Na and Son, 2021). For the waves with shorter wave period, maximum horizontal velocity was less reduced compared to incident wave speed while breaking-induced air entrainment was occurred intensely, leading to a significant reduction of wave impact pressure at the crest wall. For the waves with longer wave periods, less air wave entrained and the wave structure followed a flip-through mode (Cooker and Peregrine, 1991), resulting in an abrupt increase of the impact pressure.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.87-95
• /
• 2007

This study analyzed ground settlement and ground stress depending on tunnel excavation and the ground reinforcing grouting methods for double line road tunnel through deep weathered zone. Diameter of double line road tunnel was approximately 12m and umbrella arch method and side wall reinforcing grouting were applied. The ring-cut split excavation method and CD-cut excavation method for excavation method were applied. Analyses of failure rate and vertical stress ratio show that the tunnel for which the height of the cover (H) was higher than four times the diameter, can be considered a deep tunnel. Comparisons of various excavation and ground reinforcement methods showed that CD-cut method results in lower surface and crown settlement, and lower failure rate than that obtained by Ring-cut split method. In addition, the side wall reinforcing grouting resulted in reduction of tunnel displacement and settlement.

• Tunnel and Underground Space
• /
• v.3 no.1
• /
• pp.54-62
• /
• 1993

In order to evaluate the necessity for the support during the excavation of the transport drift and use the data for design applications, laboratory testings of mechanical properties of rock samples and engineering rock mass classifications on this study site were performed. The values of RMR and Q-system are 68 and 11.8, respectively. Since these results were evaluated as good, this rock mass were determined to be unsupported. Full face excavation method was determined to be suitable for excavating this drift. In case of excavation, smooth blasting techniques must be carried out at the wall rock and the crown. However, considering the blast vibration etc. that have an effect on the surrounding rock mass, approximately less than 9kg of explosive charges per blast should be maintained.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.21 no.2
• /
• pp.587-592
• /
• 1994

The dentigerous cyst originates through alteration of the reduced enamel epithelium after amelogenesis is completed, with accumulation of fluid between the layers of the enamel epithelium or between this epithelium and the tooth crown. It is always associated with unerupted teeth. There are two methods of treament which are generally accepted. One is the enucleation of the cystic sac in its entirety, the other is the Partch operation, or the marsupialization, by which the cyst is uncovered or "deroofed" and the cystic lining made continuous with the oral avity or surrounding structures. The present case report showed that in instance of dentigerous cyst & odontogenic keratocyst surgical enucleation followed by careful excision of all cyst wall was successfully carried out and recovery and healing were rapid and uncomplicated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.153-159
• /
• 2007

The performance of a direct-injection type diesel engine often depends on the strength of air flow in the cylinder, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the process of combustion in the cylinder was affected by the mixture formation process. In the present paper, high speed photography was employed to investigate the effectiveness of holes penetrated from the bottom of cavity wall to piston crown for some more useful utilization of air. The holes would function to improve mixing of fuel and air by the increase of air flow in the cylinder. The results obtained are summarized as follows, (1) Activated first of the combustion by shorten of ignition timing and rapid flame propagation (2) Raised the combustion peak pressure, more close to TDC the formation timing of peak pressure.

• Journal of the Korean Society of Safety
• /
• v.13 no.2
• /
• pp.122-129
• /
• 1998

A field experiment was performed to analyze the properties of SFRS(steel fiber reinforced shotcrete) against WMRS(wire mesh reinforced shotcrete) with some experimental parameters. The parameters were reinforcing methods(steel fiber and wire mesh), steel fiber contents(0.5%, 0.75%, and 1.0%), silica fume contents(0.0% and 10.0%), spraying thicknesses of layer(10㎝, 8㎝, and 6㎝), and spraying parts(side wall, shoulder, and crown). According to the analyzed results, the mechanical properties of SFRS such as compressive strength, flexural strength, and load-carrying capacity after cracks were improved. And the economic evaluation was also performed on the basis of the required thickness of the layer and other researcher's results for rebound ratios. From the results of this tests, it is found that the traditional WMRS may be substituted by the SFRS in the viewpoint of the economic evaluation as well as the mechanical properties. In additions, the silica fume, even if it is very expensive, can significantly improve the mechanical properties of the shotcrete regardless of mixing with or without the steel fiber.

• Tunnel and Underground Space
• /
• v.5 no.2
• /
• pp.95-103
• /
• 1995

In this paper the stress redistribution around tunnel face was analyzed by using a three-dimensional finite element model. The effects of in-situ stress levels, excavation sequences, stiffness difference between the hard ground and the weak zone on the stress redistributions were considered. Displacement and stress changes at tunnel crown, side wall, and invert were investigated throughout the sequential excavation. To show ground response, percentage of the displacement and stress variations are used as a function of normalized distance that is between the face and monitoring section. Preceding displacements and stress variations were presented to be adopted in the two-dimensional tunnel analysis.

• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.615-620
• /
• 2005

The aim of this study is to evaluate the public preference to the breakwaters of fishing harbors in Taiwan, so that the results could be applied to the successive study of breakwater landscape improvement. Among the breakwaters' photographs those took on the fishing harbors, this study picked up 4 photos for demonstration and 60 for questionnaire according to their spatial types configured with crest of breakwater, crown wall, and armoring blocks) and other landscape factors. The preference evaluation was conducted by questionnaire to the public, 385 effective questionnaires were taken into analysis. Results reveals: (1) the open, colorful, recreational and water-intimate breakwaters are preferred. (2) The combination types and visual elements (shapes, colors, textures, lines and scales) of breakwaters are also influence the public preference.