• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.249-254
• /
• 2016

This study was carried out to evaluate the efficiency of white shading agent for reduction of greenhouse air temperature and to develop cost-effective cooling strategies for strawberry seedling production during hot seasons. Experiment results showed that solar radiation ($W/m^2$) was reduced by 14~17% and 33~37% for 15% and 35% white wash shading treatments, respectively, in black shading net treatment solar radiation was reduced by 39~44% compared to non-shaded treatment. Measured greenhouse air temperatures in 15% and 35% white wash shading treatments were $38.4^{\circ}C$ and $36.5^{\circ}C$, respectively, whereas in black shading net covered greenhouses air temperature was $35.1^{\circ}C$, thereby 35% and 15% shading treatments showed 3.3 and $1.9^{\circ}C$ higher air temperatures than black net shading treatment. Crown diameter of strawberry plants in black net shading treatment was 7.5mm, and in 15% and 35% white wash shading treatments were 8.6mm and 8.3mm, respectively. Strawberry transplants grown in 35% white wash shading treatment produced the highest above ground fresh weight(7.8g), followed by 15% white wash shading(6.7g) and black net shading treatments(5.8g). Also, both 15% and 35% white wash shading treatments produced higher root fresh weight(4.1g and 4.3g) compare to black net shading treatments(2.7g).

• Korean Journal of Environment and Ecology
• /
• v.12 no.3
• /
• pp.259-270
• /
• 1998

This study, as an essential research to develope a mountainous runoff model, was conducted to clarify the hydrologic character and water budget equation of Pinus densiflora and Quercus acutissima. Net rainfall quantity division for two species was investigated at Youngsung experiment forest and Yeungnam University for 30 months(Sep. 1995-Jun. 1998). The results were summarized as follows; 1. The percentages of throughfall and stemflow to gross precipitation are 73.8% and 0.8% in the Pinus densiflora, and 76.9% and 3.8% in the Quercus acutissima, respectively 2. In the Pinus densiflora, regression fomula of stemflow, throughfall, and net rainfall to gross precipitation are S$_{f}$ = 0.01GP-2.05 ($r^2$=0.54) T$_{f}$ = 0.79Gp - 26.04 ($r^2$=0.92), N$_{r}$ = 0.81Gp - 28.09 ($r^2$=0.92). Stemflow and throughfall increased in direct proportion to gross precipitation. 3. In the Quercus acutissima, regression fomula of stemflow, throughfall, and net rainfall to gross precipitation are S$_{f}$ = 0.03Gp + 12.25 ($r^2$=0.74), T$_{f}$ = 0.78Gp + 19.75 ($r^2$=0.96), N$_{r}$ = 0.81Gp + 3199 ($r^2$=0.96), respectively. Comparing with two species, gross precipitation has a much larger effect on the stemflow and throughfall of Quercus acutissima than those of Pinus densiflora. 4. In the analysis of intercorrelation between stemflow and throughfall of each species and crown area(CA), diameter at breast height(DBH), and gross precipitation(Gp), correlation coefficient was higher by following order at each species; Gp>CA>DBH on stemflow of Pinus densinora, Gp>DBH>CA on stemflow of Quercus acutissima, and Gp>CA>DBH on throughfall of Pinus densiflora and Quercus acutissima.ssima.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.5
• /
• pp.514-523
• /
• 2004

Statement of problem: All-ceramic restorations have been advocated for superior esthetics. Various post and core systems have been used to improve the strength of damaged teeth, but it is unclear whether they affect the final shade of finished all-ceramic restorations. Purpose: The influence of different types of post and core systems on light transmission through all-ceramic crowns was assessed by spectrophotometric analysis. Also the masking effect of different thickness of ceramic ingot was evaluated. Material and Methods : Forty-five sample disks (15mm in diameter) at several thickness(1.0, 1.5, 2.0mm) and value(shade 100, 200, 300) were made in heat pressed ceramic(IPS-Empress). Background specimens simulating gold-alloy cast posts(Type III casting gold alloy), metal posts(Ni-Cr casting alloy) and ceramic posts(CosmoPost) were fabrica-ted. Resin composite(Z250, A3 shade) was used as a tooth substrate reference. For each combination, the change in color was measured with a spectrophotometer. Readings were performed for 2 conditions (1) ability of ceramic to mask the core in relation to its thickness(1.0, 1.5, or 2.0mm) ; (2) influence of post and core types on the final color of the ceramic. Data were recorded according to the CIE $L^*a^*b^*$ systems and color difference($\Delta$E) was calculated. Results: 100 shade ingot: when ceramic thickness was 1.0mm, $\Delta$E value for ceramic post larger than 1 but $\Delta$E value for metal and gold post was larger than 2. For ceramic thickness of 1.5mm, only $\Delta$E value for metal was larger than 2, and the other samples' $\Delta$E value was smaller than 2. For ceramic thickness of 2.0mm, $\Delta$E values for all specimens was smaller than 2. 200 shade ingot: when ceramic thickness was 1.0mm, $\Delta$E value for ceramic post was smaller than 1 but $\Delta$E value for metal and gold post was larger than 2. For ceramic thickness of 1.5 mm, only the $\Delta$E value for metal was larger than 2, and the other samples' $\Delta$E value was smaller than 2. For ceramic thickness of 2.0mm, $\Delta$E values for all specimens was smaller than 1. 300 shade ingot: when ceramic thickness was 1.0mm, only $\Delta$E value for metal was larger than 2 and the other samples' $\Delta$E value was smaller than 2. For ceramic thickness of 1.5mm, $\Delta$E values for all specimens was smaller than 1. For ceramic thickness of 2.0mm, $\Delta$E values for all specimens was smaller than 1. Conclusion: The final esthetic result of the IPS-Empress glass-ceramic restoration was not affected by the presence of different core materials when the thickness was more than 2.0 mm. When ceramic thickness decreases to 1.5mm, it is advised to take the substrate aspects into consideration. If the ceramic thickness is less than 1.0mm, using the tooth color matched substrate is strongly recommended.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.17-27
• /
• 1981

This study was conducted to determine the chemical composition and the mechanical properties of four commercially available low gold-based crown and bridge alloy produced in Korea. Four dental casting gold-silver-palladium alloys, i.e., A, B, C and D (code of alloys) were selected for the evaluation of chemical composition, ultimate tensile strength, elongation. values and Vickers hardness. The chemical composition of test specimens was analyzed by both emission spectrography and wet gravitation method with a 1.5gm of low gold ingot. The tensile properties and Vickers hardness was determined with cast specimens treated in following three conditions; as-cast, softening heat treatment and hardening heat treatment. The tensile testing bars were cast in accordance with the model designed by Gettleman and Harrison (1969) which was modified from the A. D. A. Specification No. 14 for dental chromium-cobalt casting alloy. Nine tensile test specimens were made from a split silicone mold for each of the test alloys to the size of 2.5mm in diameter and a gauge length of 10mm. All four alloys were handled in accordance with conventional methods used in Type III gold alloys. Ultimate tensile strength and elongation were measured on an Instron Universal Tensile Testing Machine (Model 1125, Japan) operated at a crosshead rate of 0.1cm/min. Elongation values were measured using Digital Measuring Microscope (MS-152, FUSOH, Japan). Vickers hardness was determined with a Vickers Hardness Tester (Model VKH-l, Japan) at a 1.0kg load on a mounted tensile test specimen. The following results were obtained from this study; 1. All tested alloys were composed of Au, Ag, Pd, Cu, Zn and Fe in common. The composition rate of gold for all four alloys was found in the range of $42{\sim}47$ weight % as shown below. Alloy A; Au 45%, Ag 40.2%, Pd 5.76%, others 9.04%. Alloy B; Au 47.1%, Ag 29.03%, Pd 6.98%, others 16.92%. Alloy C; Au 45%, .Ag 26.9%, Pd 6.83%, others 21.07%. Alloy D; Au 41.8%, Ag 34.4%, Pd 6.95%, others 16.85%. 3. The ultimate tensile strength of the four alloys was in the range of $31{\sim}82kg/mm^2$. The test results were shown in the below order from the highest value; As-cast condition; D, B, C, A. Softening heat treament; B, C, D, A. Hardening heat treatment; D, B, C, A. 4. The test :results of the elongation rate for each alloy were in the range of $0.5{\sim}18%$. The test results were shown in the below order from the highest value; As-cast condition; A, D, B, C. Softening heat treatment; A, C, D, B. Hardening heat treatment; C, D, B, A. 5. Vickers hardness for each of the four alloys was in the range of $120{\sim}230$. The test results were shown in the below order from the highest value; As-cast condition; C, B, D, A Softening heat treatment; D, B, C, A. Hardening heat treatment; D, A, C, B. 6. There were no differences in the physical properties between as-cast condition and softening heat treatment.

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.4
• /
• pp.316-323
• /
• 2011

Purpose: The purpose of this study was to investigate the effect of different thread designs on the marginal bone stresses around dental implant. Materials and methods: Standard ITI implant(ITI Dental Implant System; Straumann AG, Waldenburg, Switzerland), 4.1 mm in diameter and 10 mm in length, was selected as control. Test implants of four different thread patterns were created based on control implant, i.e. maintaining all geometrical design of control implant except thread pattern. Four thread designs used in test implants include (1) small V-shape screw (model A), (2) large V-shape screw (model B), (3) buttress screw (model C), and (4) trapezoid screw (model D). Surface area for unit length of implant was 14.4 $mm^2$ (control), 21.7 (small V-shape screw), 20.6 (large V-shape screw), 17.0 (buttress screw) and 28.7 $mm^2$ (trapezoid screw). Finite element models of implant/bone complex were created using an axisymmetric scheme with the use of NISA II/DISPLAY III (Engineering Mechanics Research Corporation, Troy, MI, USA). A load of 100 N applied to the central node on the crown top either in parallel direction or at 30 degree to the implant axis (in order to apply non-axial load to the implant NKTP type 34 element was employed). Quantification and comparison of the peak stress in the marginal bone of each implant model was made using a series of regression analyses based on the stress data calculated at the 5 reference points which were set at 0.2, 0.4, 0.6, 0.8 and 1.0 mm from implant wall on the marginal bone surface. Results: Results showed that although severe stress concentration on the marginal bone cannot be avoided a substantial reduction in the peak stress is achievable using different thread design. The peak marginal bone stresses under vertical loading condition were 7.84, 6.45, 5.96, 6.85, 5.39 MPa for control and model A, B, C and D, respectively. And 29.18, 26.45, 25.12, 27.37, 23.58 MPa when subject to inclined loading. Conclusion: It was concluded that the thread design is an important influential factor to the marginal bone stresses.

• Journal of Korean Society of Forest Science
• /
• v.79 no.4
• /
• pp.388-397
• /
• 1990

This study was conducted to investigate the changes of land use and stand volume around Mt. Kuem-O by B/W aerial photographs in 1979 and B/W Infrared aerial photographs in 1988. The results obtained in this study were as follow : 1. In classification of forest type on aerial photographs, coniferous stand was dark tone and hardwood stand was light tone and irregularly rounded crowns. 2. In classification of coniferous stand, Pinus densiflora was narraw cone and rounded tip of crowns and rough texture, Pinus rigida was irregulary rounded and broadly conical crowns. 3. To refer to changes of forest land area, mixed forest was changed into P. desiflora (687ha), P. rigida (130ha) and hardwood stand (219ha). 4. The regression equations between crown diameter and DBH were significant at 1% level by F-test in all stands. So the equation, D=a+bCD was used to estimate DBH. 5. The tree height curve equations were significant at 1% level by F-test in all stands. To estimate tree height the equation, logH=loga+blogD was adopted in P. densiflora and L. leptolepis and $H=a-bD+cD^2$ was adopted in P. rigida, hardwood stand and mixed forest. 6. The highest volume per hectare was observed in L. leptolepis and mixed forest showed the greatest growth percentage, while the lowest volume per hectare and growth percentage were observed in hardwood stand.

• Journal of Bio-Environment Control
• /
• v.28 no.4
• /
• pp.429-437
• /
• 2019

This study was conducted to examine the effect of humidification and shading during cutting propagation on growth and development of strawberry (Fragaria x ananassa Duch.) 'Maehyang' plants at a propagation stage. The runner cuttings were stuck on Nov. 23, 2017 in propagation benches set in a Venlo-type glasshouse. Four shading treatments, no shading (control, C), 55% shading with white lawn (W55), 55% black shading net (B55), or 100% black plastic film (B100) with either an intermittent fog system (H) or without fog system. The shading and fog systems were removed 2 weeks after sticking of strawberry cuttings. A nutrient solution for strawberry, which was developed by Yamazaki, was supplied once a day with electrical conductivity (EC) $1.6dS{\cdot}m^{-1}$ and pH 5.8. Growth parameters such as plant height, longest root, crown diameter, leaf chlorophyll, leaf area and fresh and dry weight were measured at 7 days and 26 days after sticking. There was no significant difference in growth of above-aerial part of strawberry. The overall growth of the strawberry roots was better grew by providing fog than that not provide fog. The root fresh weight and root dry weight after 26 days after sticking of strawberry cutting was the best in the treatment that provided fog system without shading (CH). The longest root after 26 days after sticking of strawberry cutting was the best in the treatments that provided fog system with either 55% white lawn (W55H) and 55% black shading net (B55H). These results suggest that morphogenesis of these plants were affected by humidification and shading types. In a broader perspective, these results can be used to optimize studies of other crops grown from cuttings.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.192-211
• /
• 2021

In Seongju, Gyengsangbuk-do, the Placenta Chamber (胎室, Taesil) of 18 sons and a son of the crown prince of King Sejong(世宗大王) is located in one place. Taesil refers to the place where the umbilical cord and placenta, which are separated when the baby is born, are placed in a jar made of pottery and stone box and then buried on the ground. The placenta chamber in Seongju has the Buncheong ware (粉靑沙器) cover buried on the ground to protect the baby's placenta. These covers are all hemispherical, with a diameter of more the 20cm. The decorations were made using black and white inlaid techniques only on the outside. The Buncheong ware cover with this shape and pattern has been confirmed only in the placenta chamber in Seongju. This study targets 6 of the Buncheong ware cover whose owners were identified, when and where they were prepared, what the stylistic features and meanings are, and where it was produced. The results of the study are as follows. First, ss a result of reviewing the production background and procurement system of this bowl, it was inferred that it was sourced from Jangheunggo (長興庫) at the central government office, between 1436 and 1439, when the event to bury the placenta of royal members in the ground was the most active. Second, it analyzed the unique features of this cover, such as the shape, pattern, and baked traces. The shape and pattern were compared to the ritual objects contained in the Sejong Silok Oryeui (『世宗實錄』 「五禮」, Five Rites of King Sejong Chronicle) and the lid of the royal placenta jar made in the 15th and 16th centuries. Third, this study suggests that the baking method was based on the shape and location of the traces remaining outside the cover. Finally, the following data were used to estimate the production site: the relationship with the 'Jagiso (磁器所, ceramic workshop) registered in the Sejong Silok Jiriji (『世宗實錄』 「地理志」, Geographical Appendix of King Sejong Chronicle); various records of contribution and dedication about the Buncheong ware made here; and the Buncheong ware and related tools excavated from the kiln site in the area. The place where the Buncheong ware cover was produced is estimated to be the most likely production site for the kiln site in Chunghyo-dong Kiln Site, located in Jeolla-do province by synthesizing the data above.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.6
• /
• pp.111-119
• /
• 2018

This study was carried out to investigate the growth characteristics and propagation methods of the Korean native Amelanchier asiatica, A. arborea, and A. alnifolia as fruit trees for gardens. Due to the lack of recent research on Amelanchier spp., their superficial classification is still unclear and the names are being used interchangeably. The results are obtained as follows : A. arborea and A. alnifolia were globular type multi-stemmed shrubs. A 20-year-old tree of A. asiatica was 7.8m in height, with a 5.2m crown width, with one trunk. As for the morphological characteristics, leaves of A. asiatica were oblong, with an acuminate of, 6.1cm and 3.6cm width, but A. arborea and A. alnifolia had acute obovate leaves. The leaf size of A. alnifolia was the largest among the three species. The flower size of A. asiatica was bigger than that of A. arborea and A. alnifolia. In addition, its petals and flower clusters were also the largest among the three species. The flowering of A. asiatica initiated on April 21 and then bloomed for a duration of 24 days in Osan, while that of A. arborea and A. alnifolia initiated flowering on April 12 and then bloomed for a duration of 22 days in the same location. The fruit of A. arborea and A. alnifolia were green on May 10~12, it changed into purplish red on May 24~26, and its matured on June 1~3. The duration of fruit persistence of A. arborea and A. alnifolia were 48~50 days. On the other hand, A. asiatica showed greenish fruit on May 20, it became red on September 4, and had fallen by October 3. The fruit size was the largest at 1.03cm of height and 1.12cm of diameter in the A. arborea, followed by the big berry of A. alnifolia and the smallest fruit in the native, A. asiatica. It was difficult to root due to the hardwood cutting of A. arborea at a 40% rate of rooting. In the softwood cutting, the rooting rate of A. arborea was increased by the treatment with concentrated IBA, especially at 5,000 and 7,000ppm. The optimum date for cutting was on June 27, when the rooting rate was more than 80%. The most effective method for rooting of A. arborea was rootone or 7,000 ppm IBA treatment on June 27 softwood cuttings, which showed a rooting rate of over 80%.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.497-503
• /
• 2022

This study was conducted to investigate the horticultural media + decomposed granite + reused rock wool in the following mixing ratio: Control = 100:0, M1 = 80:0:20, M2 = 60:30:10, M3 = 40:30:30, M4 = 30:40:30, M5 = 0:50:50 (reused rockwool : decomposed granite : horticultural media) and develop the physicochemical properties and the growth of 'Sulhyang' strawberry runner plant. In the physical aspect of the horticultural media, statistical differences were recognized that the bulk density and particle density were lower in the control and M1. But the bulk density and particle density were high in the M3, M4, and M5, because it had high mixing ratio between recycled rock wool and decomposed granite. EAW and WBC showed a similar tendency. The air porosity and total porosity were higher in control and M1 than M3, M4, M5. Exchangeable cation (K⁺, Ca²⁺, Na⁺, Mg²⁺) and base replacement capacity (CEC) were higher in control and M1, than M2, M3, M4, and M5. As a result of the cultivation of 'Sulhyang' runner plant, the plant length was long in M2, 32.1 cm and smaller than M5 to 28.4 cm. However, if the crown diameter, which is the growth indicator of the runner plant, all 6 treatments were formed 11.23 mm-12.03 mm, which is considered to be suitable for the growth of the runner plant. There wasn't a statistical difference between the weight and dry weight of the root. As a result, the growth difference of the seedlings by the horticulture media was similar. Therefore, considering the physical properties of the horticultural media, it was judged that the air porosity and total porosity would be improved when the recycled rock wool and the decomposed granite were properly mixed rather than the use of the horticultural media as a single medium, which would be advantageous for irrigation management.