• 한국분무공학회지
• /
• 제12권2호
• /
• pp.115-122
• /
• 2007

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomize. internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD (Sauter Mean Diameters) distribution by using Planar Liquid Laser Induced Fluorescence technique. The objectives of this research are get a droplet distributions and drop size measurements of each condition and compare with the other flow effects. As the result, This research has been showned that droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects, and normalized distance from the injector exit length(x/d, y/d). There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.486-491
• /
• 2008

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomizer internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD(Sauter Mean Diameters) distribution by using PLLIF(Planar Liquid Laser Induced Fluorescence) technique. The objectives of this research are getting a droplet distribution and drop size measurement of each condition and compare with the other flows effect. As the result, This research have been showed the droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects and normalized distance from the injector exit length.(x/d, y/d)There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.

• 대한토목학회논문집
• /
• 제7권1호
• /
• pp.11-22
• /
• 1987

흐름수역(水域)에서 연직상향으로 방류되는 평면부력(平面浮力)?의 거동이 연속방정식(連續方程式), 운동량방정식(運動量方程式) 및 추적물수송식(追跡物輸送式)의 기본방정식을 수치적(數値的)으로 풀음으로서 해석(解析)된다. 난류확산(亂流擴散)에는 Prandtl의 혼합거리이론(混合距離理論)을 도입한 난류수송모형(亂流輸送模型)이 이용된다. 수치해과정(數値解過程)은 기본방정식을 유함수(流凾數)(stream function)식(式)과 골도수송(滑度輸送)(vorticity transport)식을(式) 이용하여 변환(變換)한 후, ?방류속도(放流速度), ?방류구폭(放流口幅) 등(等)으로 표현되는 변수(變數)와 흐름을 지배(支配)하는 무차원매개변수(無次元媒介變數)를 도입하여 무차원화(無次元化)하고 successive under-relaxation을 이용하여 Gauss-Seidal 반복법(反復法)으로 해를(解) 구(求)하는 것이다. 수치실험(數値實驗)은 방류(放流)Froude수(數)가 4~32, 방류속도(放流速度)와 가로흐름속도와의 비로(比) 정의되는 속도비가 8~15 의 범위의 흐름영역(領域)에서 수행되었다. 부력(浮力)?으로 인한 주변(周邊)흐름수역(水域)의 속도변화(速度變化), 온도상승(溫度上昇)범위, 흐름상태 및 골도(滑度)가 조사되었으며, ?의 경로에 대한 속도비와 방류밀도Froude 수의 영향이 또한 조사되었다. ?중심선의 속도, 온도변화, 국부밀도(局部密度)Froude 수(數)의 변화가 계산되며 퍼짐율(spreading rate)과 확산비(擴散比)(dispersion ratio)가 방류밀도(放流密度)Froude 수, 국부밀도(局部密度)Froude 수(數) 및 속도비(速度比)의 항(項)으로 해석되었다. 또한 속도와 온도분포를 상사(相似)(similarity)로 나타낼 수 있음이 밝혀졌으며, Gaussian 분포(分布)를 이용한 적분형해석(積分型解析)(integral type analysis)이 가능한 것으로 사료된다.

• Journal of Mechanical Science and Technology
• /
• 제16권9호
• /
• pp.1121-1136
• /
• 2002

The flow characteristics of film coolant issuing into turbulent boundary layer developing on a convex surface have been investigated by means of flow visualization and three-dimensional velocity measurement. The Schlieren optical system with a spark light source was adopted to visualize the jet trajectory injected at 35° and 90° inclination angles. A five-hole directional pressure probe was used to measure three-dimensional mean velocity components at the injection angle of 35°. Flow visualization shows that at the 90° injection, the jet flow is greatly changed near the jet exit due to strong interaction with the crossflow. On the other hand, the balance between radial pressure gradient and centrifugal force plays an important role to govern the jet flow at the 35° injection. The velocity measurement shows that at a velocity ratio of 0.5, the curvature stabilizes downstream flow, which results in weakening of the bound vortex structure. However, the injectant flow is separated from the convex wall gradually, and the bound vortex maintains its structure far downstream at a velocity ratio of 1.98 with two pairs of counter rotating vortices.

• 한국항공우주학회지
• /
• 제32권4호
• /
• pp.73-79
• /
• 2004

초음속 유동하에서 측 추력기의 후방에 램프를 설치하였을 경우의 유통 현상을 실험 및 수치해석을 이용하여 해석하였다. 실험적인 방법으로, 가시화방법으로는 쉴리렌, 압력 측정을 위한 방법으로 압력 탭 (Pressure Tap), Pressure Sensitive Paint를 이용하였으며, 수치해석을 위하여 AeroSoft사의 GASP ver. 4.0을 사용하였다. 실험조건은 자유류의 흐름이 마하수 4 측 추력기와 자유류의 압력비가 532 이었으며 GASP을 사용하여 3D 램프형상에 대한 고찰을 하였다. 위의 모든 결과들은 후방의 램프가 없을 경우와 비교를 통하여 램프를 장착하였을 경우 수직력의 감소없이 피칭다운 모멘트가 70% 정도 감소함을 확인하였다.

• 대한기계학회논문집B
• /
• 제23권2호
• /
• pp.218-225
• /
• 1999

Flow visualization study has been conducted to simulate the turbulent dispersion behavior of a crossflow jet physically under the conditions of various thermal stratification in a wind tunnel. A smoke jet with the constant ratio of the jet to freestream velocity is injected normally to the cross flow of the thermally stratified wind tunnel(TSWT) for flow visualization. The typical natures of the smoke dispersion under different thermal stratifications such as neutral, weakly stable, strongly stable, weakly unstable, strongly unstable and inversion layer are successfully reproduced in the TSWT. The Instantaneous velocity and temperature fluctuations are measured by using a cold and hot-wire combination probe. The time averaged dispersion behaviors, the centerline trajectories, the spreading angles and the virtual origins of the cross jet are deduced from the edge detected images with respect to the stability parameter. All the general characteristics of the turbulent dispersion behavior reveal that the definitely different dispersion mechanisms are inherent in both stable and unstable conditions. It is conjectured that the turbulent statistics obtained in the various stability conditions quantitatively demonstrate the vertical scalar flux plays a key role in the turbulent dispersion behavior.

• 한국분무공학회지
• /
• 제13권2호
• /
• pp.99-106
• /
• 2008

In this study, spray characteristics research of steady/pulsed injection in crossflow was performed experimentally in the model ramjet combustor. High-speed-camera photography was performed through a visualization window of model combustor, and then, steady and pulsed spray structures were observed and analyzed. Varying influx air temperature and fuel species, we could obtain the trajectory correlation in the steady injection case. In the experiment of pulsed injection, it is found that the pulsed frequency hardly influences spray trajectory. Also, it is found that, in the same injection pressure differential, the trajectory correlation of steady condition can be used for estimating pulsed spray trajectory.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.97-103
• /
• 2008

Unsteady three-dimensional flowfields generated by transverse fuel injection into a supersonic mainstream are simulated with a DES turbulence model. Comparisons are made with experimental results in term of the temporal eddy position and eddy formation frequency. The vorticity field around the jet exit is also analyzed to understand the formation mechanism of the jet vortical structures. Results indicate that the DES model correctly predicts the convection characteristics of the large scale eddies. However, it is also observed that the numerical results slightly overpredict the eddy formation frequency. The jet vortical structures are developed from the competing vortices in the recirculation region of upstream boundary.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.97-103
• /
• 2008

Unsteady three-dimensional flowfields generated by transverse fuel injection into a supersonic mainstream are simulated with a DES turbulence model. Comparisons are made with experimental results in term of the temporal eddy position and eddy formation frequency. The vorticity field around the jet exit is also analyzed to understand the formation mechanism of the jet vortical structures. Results indicate that the DES model correctly predicts the convection characteristics of the large scale eddies. However, it is also observed that the numerical results slightly overpredict the eddy formation frequency. The jet vortical structures are developed from the competing vortices in the recirculation region of upstream boundary.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.79-84
• /
• 2004

This paper report our preliminary results of characterizing the jet structures of kerosene injection into quiescent atmosphere and a Mach 2.5 crossflow at various preheat temperature. A heating system has been designed and tested that can prepare heated kerosene of 0.8 kg up to 670 K at a pressure of 5.5 ㎫. Temperature measurement near the injector shows that the temperature of pressurized kerosene can be kept constant during the experimental duration. Comparison of kerosene jet structures in the preheat temperature range of 290-550 K demonstrates that with injection pressure of 4 ㎫ the jet plume turns into vapor phase completely at injection temperature of 550 K, while keeping the penetration depth essentially unchanged. The results suggest that the injection of vaporized fuel would improve the performance of a liquid hydrocarbon-fueled supersonic combustor because the evaporation process is now omitted.