• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1386-1392
• /
• 2000

This paper presents a new prediction method of radiated noise from grille of the airconditioning appliance. Laminar vortex sheddings behind a circular cylinder are simulated by solving two dimensional unsteady incompressible Navier-Stokes equation. The Finite Elements Method(FEM) and unstructured grid generation technique are applied to solve, the unsteady lift/drag coefficients are obtained to compute far-field noise using Lighthill's acoustic analogy. Grille is divided into some cylinder segments, and radiated noise from grille is obtained by summing noise generated from each segment. The effects of changing cross section of cylinder and grille geometry are studied. And sound pressure levels radiated from typical H-type grille are measured in KAIST anechoic wind tunnel at various inflow conditions and compared with numerical predictions.

• Earthquakes and Structures
• /
• v.25 no.2
• /
• pp.113-123
• /
• 2023

A novel type of buckling restrained brace with built-up angle steel was developed. The core segment was formed by welding angle steel, and the middle section was reduced by cutting technology to solve the problem that the end of BRB was easy to buckle. The experimental program has been undertaken to study the performance of BRBs with different unbonded materials (silica gel, kraft paper) and different filler materials (ordinary concrete, full light-weight concrete). Four specimens were designed and fabricated for low cycle reciprocating load tests to simulate horizontal seismic action. The failure mode, hysteretic curves, tension-compression unbalance coefficient and other mechanical parameters were compared and analyzed. The finite element software ABAQUS was used to conduct numerical simulation, and the simulation results were compared with the experimental phenomena. The test results indicated that the hysteretic curve of each specimen was plump. Sustaining cumulative strains of each specimen was greater than the minimum value of 200 required by the code, which indicated the ductility of BRB was relatively good. The energy dissipation coefficient of the specimen with silica gel as unbonded material was about 13% higher than that with kraft paper. The experimental results were in good agreement with the simulation results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.249-252
• /
• 2008

A study for the nonlinear analysis method of RC(Reinforced Concrete) beams with unbonded prestressing CFRP plate is presented. The cross-section of RC beam element is idealized as an assemblage of concrete and reinforcing steel fibers in order to account for varied material properties within the cross-section of the element. The unbonded CFRP plate is modeled as a series of the CFRP plate segments each of which is linked to the RC beam element, but slips without any resistance to simulate the unbonded behavior of the CFRP plate. The stress of each CFRP plate segment is redistributed iteratively using the force equilibrium relationship at each common node until it reaches at the same stress level. To evaluate the validity of the proposed analysis method, the results of ultimate analysis of the reinforced concrete beams with unbonded prestressing CFRP plates are compared with the experimental results obtained from other investigators. The proposed analysis method is found to predict ultimate behaviors of these beams fairly well.

• Journal of Korean Society of Disaster and Security
• /
• v.16 no.3
• /
• pp.17-26
• /
• 2023

Prestressed Concrete (PSC) girders are divided into pre- and post-tension types as prestressing method, and I- and U-type as cross-sectional shape. There are both advantages and disadvantages depending on each prestressing method and cross-sectional shape, and each method is applied to bridge construction sites. In this study, a new girder design was attempted to develop that overcomes its shortcomings by using the pretension method and U-type cross sectional shape. Its structural performance was verified in this study. Pretension type girders are mainly manufactured in factories because they require a reaction arm and related facilities, and have the disadvantage of being limited in weight and span length for road transportation. In addition, in the case of the U-type cross-section, structural stability is very reliable during construction against overturning, but its own weight is relatively large comparing to I-type, and the post-tension method is mainly applied after on-site production. In this study, a PSC girder manufacturing method using the field pretension was proposed and a span length of 40 m real-scale test specimen was manufactured and verified its structural performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.135-140
• /
• 2009

This paper discusses how to change the electromagnetic waves' property in the cut-off causing discontinuity existing in the guiding structure of the RF passive component by using the metamaterial and elaborates on its principle. Particularly, we find and explain, from the viewpoint of electromagnetics and circuit theories, the so-called tunneling condition that when the segment with an extremely narrow cross-section leading to blockage in the parallel-plate waveguide is given the ENZ(Epsilon Near Zero) for its filling material, the wave starts to propagate through the segment. The analysis method as a transmission-line theory taking the discontinuity and material change into consideration is shown valid through the comparison with other methods for analyzing parallel-plate waveguides, and provides the illustration of the S-parameters and impedance describing the characteristics of the tunneling.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.133-133
• /
• 2017

Lodging is one of the important constraints in rice production. The lodging destroys the canopy structure, and sharply reduces the capacity of photosynthetic rate and dry matter production. In cereal crops, stem lodging can be classified into two types: stem breaking type and stem bending type. To improve stem lodging resistance, it is important to reveal strong culm traits of superior lodging resistant varieties. There are large varietal differences in parameters associated with the bending moment at breaking (M) and flexural rigidity (FR). The indica variety Takanari possesses large M due to its large section modulus (SM) despite of its small bending stress (BS), while Takanari also has large FR due to its large secondary moment of inertia (SMI) and Young's modulus (YM). To identify quantitative trait loci (QTLs) and the corresponding genes associated with the parameters for M ($=SM{\times}BS$) and FR ($=SM{\times}YM$) should enable to develop lodging resistant varieties, efficiently. In order to identify QTLs for cell wall materials such as cellulose, hemicellulose and lignin associated with BS and YM, a set of Chromosome Segment of Substitution Lines (CSSLs) consisted of 37 lines with chromosome segments of Koshihikari in the genetic background of Takanari were used. Takanari had large M and small BS as compared with Koshihikari. The QTLs for BS were estimated on chromosomes 3, 5, 6, 8, 9, 10, 11 and 12. Koshihikari alleles increased BS in these QTLs. Takanari had a large FR due to its large SMI and YM as compared with Koshihikari. The YM was increased by substitution of the Koshihikari chromosomal segments on chromosomes 2, 10 and 11. Other QTLs estimated on chromosomes 7 and 12 that Koshihikari alleles contributed to the decrease of YM. For lignin, only one major QTL for lignin density was detected on chromosome 11. Hollocellulose densities were increased by the substitution of Koshihikari segments on chromosomes 5 and 11. On the other hand, these were decreased on chromosomes 1 and 3 by substitution of Koshihikari segments. QTLs for cellulose density were estimated on chromosomes 1, 3 and 5 by substitution of Koshihikari segments. For hemicellulose, QTL on chromosome 3 showed that hemicellulose density decreased by the substitution of Koshihikari segment. However, hemicellulose densities on chromosomes 5, 8 and 11 showed the opposite effects. The QTLs for hemicellulose, cellulose, and hollocelulose densities identified on chromosome 5 overlapped with that for bending stress, indicating the positive effect of Koshihikari segment on increasing bending stress. These results suggest that some QTLs for the densities of cell wall materials contribute to increasing bending stress and Young's modulus, and could be utilized to improve the lodging resistance for both types of breaking and bending in rice varieties.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.3
• /
• pp.311-320
• /
• 2014

High strength concrete is not only vulnerable to the occurrence of spalling which generates the loss of cross-section in concrete structures but produces faster degradation in its mechanical properties than normal strength concrete in the event of fire. This study aims to evaluate fire resistance of high strength segment concrete with PET fibers mixed to prevent spalling under ISO834 (2hr) and RABT fire curve. As results, the samples without PET fibers show the concrete loss up to the depth of about 8 cm and 9.5 cm from the surface exposed to fire under ISO834 and RABT fire curve respectively. The samples mixed with PET fiber of 0.1% show no spalling under ISO834 fire curve and the spalled thickness of 6.5 cm under RABT fire curve after the fire tests. Finally, the sample mixed with PET fiber of 0.2% shows no spalling under RABT fire curve. The results indicate that the suitable amounts of PET fiber for securing fire resistance performance of this high strength segment concrete are 0.1% under ISO834 fire curve and 0.2% under RABT fire curve. However, even though spalling does not occur, it is necessary to repair the deterioration of concrete up to 4 cm from the surface exposed to fire after fire.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.853-858
• /
• 2001

The PSC bridge being built by ILM may have greater bending moment during its construction rather than after completion. When it occurs, Engineer should suggest to reduce stress-resultants than to make bigger cross-section with considering stability ,economics, and proper span-to-depth ratio. The used method is to install extruded nose at the end of girder. It substitutes the weighted segment for the light. From the reference, the stiffness of extruded nose, is 1/10 of the main girder, and the length is 60 to 70% of the length of the span, with little justification. In this study, the proper length and stiffness of the nose element is determined by the parametric study and idealizing procedure. The results about the extruded nose through the mixing of the parameter of its stiffness and length, the proper length of extruded nose is 80% of the longest span and the proper stiffenss is 13% of the bending stiffness of the superstructure and the proper length of extruded nose is 70% of the longest span and the proper stiffness is 9.5% of the bending stiffness of the superstructure.

• Wind and Structures
• /
• v.20 no.5
• /
• pp.683-699
• /
• 2015

Lighting poles and antenna masts are typically high, slender and light structures. Moreover, they are often characterized by distributed eccentricities that make very complex their shape. Experience teaches that this structural type frequently suffers severe damage and even collapses due to wind actions. To understand and interpret the aerodynamic and aeroelastic behavior of lighting poles and antenna masts, this paper presents the results of static and aeroelastic wind tunnel tests carried out on a complex prismatic element representing a segment of the shaft of such structures. Static tests are aimed at determining the aerodynamic coefficients and the Strouhal number of the test element cross-section; the former are used to evaluate the critical conditions for galloping occurrence based on quasi-steady theory; the latter provides the critical conditions for vortex-induced vibrations. Aeroelastic tests are aimed at reproducing the real behavior of the test element and at verifying the validity and reliability of quasi-steady theory. The galloping hysteresis phenomenon is identified through aeroelastic experiments conducted on increasing and decreasing the mean wind velocity.

• Steel and Composite Structures
• /
• v.20 no.4
• /
• pp.813-832
• /
• 2016

This research deals with the behavior of Composite Box Girder Bridges (CBGBs) subjected to environmental effects such as solar radiation, atmospheric temperature, and wind speed. It is based on temperature and thermal stress results, which were recorded hourly from a full-scale experimental CBGB segment and Finite Element (FE) thermal analysis. The Hemi-cube method was adopted to achieve the accuracy in temperature distributions and variations in a composition system during the daily environmental variations. Analytical findings were compared with the experimental measurements, and a good agreement was found. On the other hand, parametric investigations are carried out to investigate the effect of the cross-section geometry and orientation of the longitudinal axis of CBGB on the thermal response and stress distributions. Based upon individual parametric investigations, some remarks related to the thermal loading parameters were submitted. Additionally, some observations about the CBGB configurations were identified, which must be taken into account in the design process. Finally, this research indicates that the design temperature distribution with a uniform differential between the concrete slab and the steel girder is inappropriate for describing the thermal impacts in design objective.