• 한국해양공학회지
• /
• 제25권1호
• /
• pp.14-21
• /
• 2011

The purpose of this study is to quantify the erosional parameters, such as the critical shear stress for erosion and the erosion rate coefficient for cohesive sediments from the Mokpo coast. Using Chonbuk annular flume, five erosion tests were conducted under the uniform bed condition but a different bed density respectively. Erosion test results for Mokpo sediments have shown increases in the range of $0.16{\sim}0.43\;N/m^2$ but decreases exponentially in the range of $272{\sim}4.64\;mg/cm^2{\cdot}hr$ for the given bed shear stress of $1.14{\sim}1.34\;g/cm^3$. The erosional parameters of Mokpo sediments are found to vary remarkably in quantity compared with those for cohesive sediments from other sites. On the whole, the value of Mokpo coast sediments appears to be similar to Kunsan sediments but smaller than Saemankeum and Okeechobee sediments. On the other hand, Mokpo sediments have been shown to be larger than Saemankeum and Okeechobee sediments but smaller than Kunsan sediments.

• 수산해양기술연구
• /
• 제28권3호
• /
• pp.295-305
• /
• 1992

The critical strain energy release rate and the failure mechanisms of glass-carbon epoxy resin hybrid composites are investigated in the temperature range of the ambient temperature to 8$0^{\circ}C$. The direction of laminates and the volume fraction are [(+45, -45, 0, 0) sub(2) ] sub(s), 50%, respectively. The major failure mechanisms of these composites are studied using the scanning electron microscope for the fracture surface. Results are summarized as follows: 1) The critical strain energy release rate shows a maximum at ambient temperature and it tends to decrease as temperature goes up. 2) The critical strain energy release rate increases as the content of glass increases, and especially shows dramatic increase for the high glass fiber content specimens. 3) Major failure mechanisms can be classfied such as localized shear yielding, fiber-matrix debonding, matrix micro-cracking, and fiber pull-out and/or delamination.

• 대한금속재료학회지
• /
• 제47권7호
• /
• pp.397-405
• /
• 2009

The high strain rate deformation behavior of ultra-fine grained 5083 aluminum alloys prepared via equal channel angular (ECA) extrusion was investigated in this study. The microstructure of ECA extruded specimens consisted of ultra-fine grains, and contained a considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. According to the dynamic torsion test results, the maximum shear stress and fracture shear strain of the route A (no rotation) specimen were lower than those of route C ($180^{\circ}$ rotation) specimen since that adiabatic shear bands of $100{\mu}m$ in width were formed in the route A specimen. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity associated with ECA operations.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(1)
• /
• pp.553-558
• /
• 1998

The calibrating method for an electrochemical Probe, neglecting the effect of the normal velocity on the mass transport, can cause large errors when applied to the measurement of wall shear rates in thin wavy flow with large amplitude waves. An extended calibrating method is developed to consider the contributions of the normal velocity. The inclusion of the turbulence-induced normal velocity term is found to have a negligible effect on the mass transfer coefficient. The contribution wave-induced normal velocity can be classified on the dimensionless parameter V. If V above a critical value of V, $V_{crit}$, the effects of the wave-induced normal velocity become larger with an increase in V. IF V its effects negligible for V < $V_{crit}$. The unknown shear rate is numerically determined by solving the 2-D mass transport equation inversely. The president inverse method can predict the unknown shear rate more accurately in thin wavy flow with large amplitude waves than the previous method.

• 한국해안해양공학회지
• /
• 제17권2호
• /
• pp.119-128
• /
• 2005

미세-점착성 퇴적물의 침식률 산정을 목적으로 국내 최초로 환형수조가 제작되었으며, 수조의 성능, 실험 방법 및 결과 등에 대한 타당성 검증을 목적으로 고령토를 이용한 침식실험이 수행되었다. 각기 다른 밀도를 갖는 균일저면 조건하에서 총 4회의 실험이 수행되었으며, 이 결과로부터 점착성 퇴적물의 침식한계 전단응력과 침식률 계수가 산정되었다. 기존의 타 연구결과와의 비교$\cdot$검토를 통하여, 본 연구에서 특수 제작된 환형수조는 성능상에 문제가 없음이 간접적으로 확인되었으며, 균일저면의 제작과정을 포함하는 침식실험 방법 및 실험 결과의 타당성이 입증되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.987-992
• /
• 1997

Burrs always come out with the machining of ducterial with small size. Though the size of burrs is small, burrs dominate deterioration of the accuracy of the micro grooves. So the burr generation model especially side burr generation model was investigated to predict the size of the burrs at the given cutting conditions. The side shear plane is introduced to build the burr generation model and the width of side shear plane nomalized with cutting depth is defined with the shear angle. From the theoretical observation, the width of side shear plane can vary up 40% of the cutting depth. To determine the size of burr and stiffness, single groovings were carried out and it was found that there exist a critical depth of cut that the size or stiffness of the burr vary.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.306-309
• /
• 2009

The influence of equal-channel angular pressing (ECAP) route on dynamic deformation behavior of ultra-fine grained Al-4.4%Mg alloys was investigated in this study. The 8-pass ECAPed specimens consisted of ultra-fine grains of $0.5{\mu}m$ in size, and contained the considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. The result of dynamic torsional tests indicated that the maximum shear stress and fracture shear strain were lowest in the specimen deformed by ECAP via route A among the 8-pass ECAPed specimens. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity related to ECAP routes.

• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.122-130
• /
• 2012

Adhesive bend and shear tests of micro-sized bonded component have been performed to clarify the relationship between effects of heat-treatment on the adhesive strength and the bonded specimen shape using Weibull analysis. Multiple micro-sized SU-8 columns with four different diameters were fabricated on a Si substrate under the same fabrication condition. Heat-treatment can improve both of the adhesive bend and shear strength. The improvement rate of the adhesive shear strength is much larger than that of the adhesive bend strength, because the residual stress, which must change by heat-treatment, should effect more strongly on the shear loading. In case of bend type test, the adhesive bend strength in the smaller diameters (50 and $75\;{\mu}m$) widely vary, because the critical size of the natural defect (micro-crack) should vary more widely in the smaller diameters. In contrast, in case of shear type test, the adhesive shear strengths in each diameter of the columns little vary. This suggests that the size of the natural defects may not strongly influence on the adhesive shear strength. All the result suggests that both of the adhesive bend and shear strengths should be complicatedly affected by heat-treatment and the bonded columnar diameter.

• Korea-Australia Rheology Journal
• /
• 제15권3호
• /
• pp.151-156
• /
• 2003

In this research, experimental studies were performed to examine the rheological behavior of equimolar solutions of cetylpyridinium chloride (CPyCl) and sodium salicylate (NaSal) solutions with concentration. The surfactant solutions were prepared by dissolving 2 mM/2 mM - 80 mM/80 mM of surfactant/counterion in double-distilled water. It has been observed that the zero shear viscosity shows abrupt changes at two critical values of C^*$ and C^{**}$. These changes are caused by the switching of relaxation mechanism with concentration of CPyCl/NaSal solutions at those concentrations. The wall slip velocities of dilute and semidilute CPyCl/NaSal solutions show a dramatic increase with shear rate where the shear viscosity exhibits shear thickening behavior for dilute solutions and shear thinning behavior for semi-dilute solutions, respectively. Considering that the dramatic increase in wall slip velocity should be related to the formation of shear-induced structure (SIS) in the surfactant solution, the shear thickening behavior of semi-dilute solutions is caused by elastic instability unlike the case of dilute solutions.

• 대한토목학회논문집
• /
• 제12권3호
• /
• pp.221-229
• /
• 1992

퇴적물(堆積物)의 형태(形態), 함수비(含水比) 및 저면전단응력(底面剪斷應力)(${\tau}_b$)이 미세퇴적물(微細堆積物)의 부상특성(浮上特性)에 미치는 영향을 연구하기 위해 순환식 개수로에서 부상실험(浮上實驗)을 하였다. 시료는 한국(韓國)의 서해안(西海岸)에 위치한 영광해역과 남동해안(南東海岸)에 위치한 영도해역에서 채취한 것을 사용하였다. 퇴적물(堆積物)의 종류 및 함수비의 크기에 따른 부상한계저면전단응력(浮上限界底面剪斷應力)(${\tau}_c$)이 유추되었다. 동일한 시료에 대해서 함수비(含水比)가 클 수록 상한계저면전단응력(浮上限界底面剪斷應力)은 감소하였으나, 부상량(浮上量)은 증가하였다. 퇴적물(堆積物)의 부상(浮上)은 퇴적물(堆積物)의 함수량(含水量)에도 크게 좌우되지만, 입자간(粒子間)의 결합력(結合力)(점참력(粘着力))을 특징짓는 퇴적물(堆積物)의 형태(形態)에도 강하게 지배되었다. 한 방향 흐름장에서 부상한계저면전단응력(浮上限界底面剪斷應力)은 파-흐름 공존장에서의 부상한계저면전단응력(浮上限界底面剪斷應力)보다 약 4배 이상 크게 나타났다. 저면전단응력(底面剪斷應力)이 작을 경우에는 실험초기(實驗初期)에 급부상(急浮上)한 후 시간이 경과할 수록 저면의 경화로 인해 부상량(浮上量) 어느 일정치에 가까와지고 있으나, 저면전단응력(底面剪斷應力)이 클 수록 시간의 경과에 따라 저변의 연약화로 인해 부상량(浮上量)도 계속적으로 증가하였다. 각(各) 실험(實驗)에 대한 초기(初期) 부하율(浮上率) $E={\alpha}_3({\tau}_b/{\tau}_c-1)^{\beta}$ (${\alpha}_3$, ${\beta}$ = 경험적 상수)을 평가하였으며, 동일한 시료에 대해서는 함수비(含水比)가 클 수록 ${\alpha}_3$와 ${\beta}$ 값이 증가하였다.