• Geomechanics and Engineering
• /
• 제17권6호
• /
• pp.553-564
• /
• 2019

This paper presents experimental results of rock-concrete bi-material discs under cyclically diametrical compression. It was found that both specimens under cyclical and static loading failed in three typical modes: shear crack, tensile crack and a combined mode of shear and wing crack. The failure modes transited gradually from the shear crack to the tensile one by increasing the interface angle between the interface and the loading direction. The cycle number and peak load increased by increasing the interface angle. The number of cycles and peak load increased with the interface groove depth and groove width, however, decreased with increase in interface groove spacing. The concrete strength can contribute more to the cycle number and peak load for specimens with a higher interface angle. Compared with the discs under static loading, the cyclically loaded discs had a lower peak load but a larger deformation. Finally, the effects of interface angle, interface asperity and concrete strength on the fatigue strength were also discussed.

• 한국산업융합학회 논문집
• /
• 제25권2_2호
• /
• pp.233-238
• /
• 2022

This study evaluated the fatigue limit depending on microcracks using 0.57 wt.% carbon steel with different Vickers hardness. The fatigue limit was almost constant up to a certain limit regardless of the carbon content. However, the fatigue limit decreased rapidly as the size of the crack increased. As the crack aspect ratio was smaller, the fatigue limit of the depth (point A) a lot decreased. The fatigue limit ratio of the depth decreased significantly because the crack propagation in the depth direction was fast as the crack aspect ratio became smaller. On the other hand, the fatigue limit ratio of surface cracks increased as the crack aspect ratio decreased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1173-1174
• /
• 2010

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.190-195
• /
• 2000

It has been established that a crack has an important effect on the dynamic behavior of a structure. This effect depends mainly on the location and depth of the crack. To identify the location and depth of a crack in a structure. Nikolakopoulos et. al. used the intersection point of the superposed contours that correspond to the eigenfrequency caused by the crack presence. However the intersecting point of the superposed contours is not only difficult to find but also incorrect to calculate. A method is presented in this paper which uses optimization technique for the location and depth of the crack. The basic idea is to find parameters which use the structural eigenfrequencies on crack depth and location and optimization algorithm. With finite element model of the structure to calculate eigenfrequencies, it is possible to formulate the inverse problem in optimization format. Method of optimization is augmented lagrange multiplier method and search direction method is BFGS variable metric method and one dimensional search method is polynomial interpolation.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.62-69
• /
• 1986

본 연구에서는 표면균열의 전파거동에 관한 연구의 일환으로 경량화재료 로서 항공기 구조용으로 널리 사용되고 있는 7075-T651 알루미늄합금을 준비하고 제하탄성 compliance법을 이용하여 표면 및 깊이 방향의 균열진전거동의 특성을 밝히고져 한다.

• 한국소음진동공학회논문집
• /
• 제15권5호
• /
• pp.620-628
• /
• 2005

In this paper, we studied about the dynamic behavior of a cracked rotating cantilever beam. The influences of a rotating angular velocity, the crack depth and the crack position on the dynamic behavior of a cracked cantilever beam have been studied by the numerical method. The equation of motion is derived by using the Lagrange's equation. The cracked cantilever beam is modeled by the Euler-Bernoulli beam theory. The crack is assumed to be in the first mode of fracture and to be always opened during the vibrations. The lateral tip-displacement and the axial tip-deflection of a rotating cantilever beam is more sensitive to the rotating angular velocity than the depth and position of crack. Totally, as the crack depth is increased, the natural frequency of a rotating cantilever beam is decreased in the first and second mode of vibration. When the crack depth is constant, the natural frequencies of a rotating cantilever beam are proportional to the rotating angular velocity in the each direction.

• 한국재료학회지
• /
• 제33권6호
• /
• pp.251-256
• /
• 2023

This study aims to examine the correlation between microstructures and the mechanical properties of two high-strength API X70 linepipe steels with different specimen directions and Moaddition. The microstructure of the Mo-added steel has an irregularly shaped AF, GB matrix with pearlite because of the relatively large deformation in the non-recrystallization temperature region, while that of the Mo-free steel shows a PF matrix with bainitic microstructure. In the Mo-added steel, the M/A (martensite-austenite) in granular bainite (GB) and pearlite act as crack initiation sites with decreased upper shelf energy and an increased ductile to brittle transition temperature (DBTT). Regardless of Mo addition, all of the steels demonstrate higher strength and lower elongation in the T direction than in the L direction because of the short dislocation glide path and ease of pile-up at grain boundaries. In addition, the impact test specimens with T-L direction had a lower impact absorbed energy and higher DBTT than those with the L-T direction because the former exhibit shorter unit crack path compared to the latter.

• 화약ㆍ발파
• /
• 제27권2호
• /
• pp.1-11
• /
• 2009

본 연구에서는 프리스플리팅 적용 시 심발 발파를 통해 먼저 자유면을 확보한 후 이에 따른 응력변화를 관찰함으로서 최 외곽영역에서 균열형성을 함에 있어서의 유리함을 판단하고자 하며 균열형성이 용이한 조건을 찾고자 한다. 수치해석에서는 터널 내 최소주응력 방향을 고려했으며 수치해석 결과 응력의 방향변화는 가압하중의 크기변화에 큰 영향이 있음을 확인할 수 있었고, 차응력이 증가할수록 균열이 증가하는 경향을 확인하였다. 모형실험결과 응력장을 고려한 프리스플리팅공법 적용으로 기존 프리스플리팅 공법에 비해 균열 제어가 용이하고, 이를 통해 이완영역 축소를 기대할 수 있으며 또한 새로운 개념의 프리스플리팅 공법의 적용성을 판단하였다.

• Computers and Concrete
• /
• 제12권3호
• /
• pp.261-283
• /
• 2013

This paper aims to contribute to the three-dimensional generalization of numerical prediction of crack propagation through the formulation of finite elements with embedded discontinuities. The analysis of crack propagation in two-dimensional problems yields lines of discontinuity that can be tracked in a relatively simple way through the sequential construction of straight line segments oriented according to the direction of failure within each finite element in the solid. In three-dimensional analysis, the construction of the discontinuity path is more complex because it requires the creation of plane surfaces within each element, which must be continuous between the elements. In the method proposed by Chaves (2003) the crack is determined by solving a problem analogous to the heat conduction problem, established from local failure orientations, based on the stress state of the mechanical problem. To minimize the computational effort, in this paper a new strategy is proposed whereby the analysis for tracking the discontinuity path is restricted to the domain formed by some elements near the crack surface that develops along the loading process. The proposed methodology is validated by performing three-dimensional analyses of basic problems of experimental fractures and comparing their results with those reported in the literature.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.122-131
• /
• 1995

The research trends for metal matrix composites have been on basic mechanical properties, fatigue behavior after aging and fractographic observations. In this study, the fatigue crack initiation as well as the fatigue crack growth behavior and the fracture mechanism were investigated through observations of the fracture surface on silicon carbide particles reinforced aluminum metal matrix composites(SiCp/Al). Based on the fractographic study done by scanning electron microscope and replica, crack growth path model and fracture mechanism are presented. The mechanical properties, such as the tensile strength, yield strength and elongation of SiCp/Al composites are improved in a longitudinal direction, however, the fatigue life is shorter than the basic Al6061 alloys. From fractographic observations, it is found that the failure mode is ductile in basic Ai6061 alloys. And because some SiC particles were pulled out from the matrix and a few SiC particles could be seen on the fracture surface of SiCp/Al, crack growth paths are believed to follow the interface of the matrix and its particles.