• Journal of Welding and Joining
• /
• v.23 no.2
• /
• pp.75-80
• /
• 2005

The effect of chemical constituents of $(Cr,\;Fe)_7C_3$ carbide phase on its hardness in the chromium-carbide type Cr white iron hardfacing weld deposits has been investigated. In order to examine $(Cr,\;Fe)_7C_3$ carbide phase, a series of filler metals with varying chromium contents was used. The alloys were deposited once or twice on a mild steel plate using the self?shielding flux cored arc welding process. The hardness of $(Cr,\;Fe)_7C_3$ carbide phase was measured by the micro-Vickers hardness test. It was shown that hardness of $(Cr,\;Fe)_7C_3$ carbide phase increased with increasing Cr content in $(Cr,\;Fe)_7C_3$ carbide phase. This behavior of the hardness of $(Cr,\;Fe)_7C_3$ carbide phase was explained by the types of chemical bonds that hold atoms together in $(Cr,\;Fe)_7C_3$ carbide phase.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.414-422
• /
• 2002

Three different multi-component white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their as-cast and solidification structures. Three combinations of the alloying elements were selected so as to obtain the different types of carbides and matrix structures : 3%C-10%Cr-5%Mo-5%W(alloy No.1), 3%C-10%V-5% Mo-5%W(alloy No. 2) and 3%C-17%Cr-3% V(alloy No.3). The as-cast microstructures were investigated with optical and scanning electron microscopes. There existed two different types of carbides, $M_7C_3$ carbide with rod-like morphology and $M_6C$ carbide with fishbone-like one, and matrix in the alloy No. 1. The alloy No. 2 consisted of MC carbide with chunky and flaky type and needle-like $M_2C$ carbide, and matrix. The chunky type referred to primary MC carbide and the flaky one to eutectic MC carbide. The morphology of the alloy No. 3 represented a typical hypo-eutectic high chromium white cast iron composed of rod-like $M_7C_3$ carbide which is very sensitive to heat flow direction and matrix. To clarify the solidification sequence, each iron(50g) was remelted at 1723K in an alumina crucible using a silicon carbide resistance furnace under argon atmosphere. The molten iron was cooled at the rate of 10K/min and quenched into water at several temperatures during thermal analysis. The solidification structures of the specimen were found to consist of austenite dendrite(${\gamma}$), $ ({\gamma}+ M_7C_3)$ eutectic and $({\gamma}+ M_6C)$ eutectic in the alloy No. 1, proeutectic MC, austenite dendrite(${\gamma}$), (${\gamma}$+MC) eutectic and $({\gamma}+ M_2C)$ eutectic in the alloy No. 2, and proeutectic $M_7C_3$ and $ ({\gamma}+ M_7C_3)$ eutectic in the alloy No 3. respectively.

• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.95-103
• /
• 2001

The properties of the detonation sprayed cermet coating are investigated through the mechanical, corrosion and erosion test. The test results are also compared with the properties of the substrate materials, STS 329J1, dual phase stainless steel and the plasma sprayed cermet coatings. The two kinds of carbide cermet power, WC+NiCr, Cr$_3$C$_2$+NiCr were used in this experiment. The experimental results showed that the anti-corrosive and anti-erosive properties of the detonation sprayed cermet coatings are superior to the plasma sprayed cermet coatings. The WC+NiCr cermet coating appears to be more effective than Cr$_3$C$_2$+NiCr cermet coating in abrasive erosion environment, whereas the Cr$_3$C$_2$+NiCr cermet coatings are more effective in cavitation erosion environment.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.408-414
• /
• 2018

This study investigates the microstructure and wear properties of cermet (ceramic + metal) coating materials manufactured using high velocity oxygen fuel (HVOF) process. Three types of HVOF coating layers are formed by depositing WC-12Co, WC-20Cr-7Ni, and Cr3C2-20NiCr (wt.%) powders on S45C steel substrate. The porosities of the coating layers are $1{\pm}0.5%$ for all three specimens. Microstructural analysis confirms the formation of second carbide phases of $W_2C$, $Co_6W_6C$, and $Cr_7C_3$ owing to decarburizing of WC phases on WC-based coating layers. In the case of WC-12Co coating, which has a high ratio of $W_2C$ phase with high brittleness, the interface property between the carbide and the metal binder slightly decreases. In the $Cr_3C_2-20CrNi$ coating layer, decarburizing almost does not occur, but fine cavities exist between the splats. The wear loss occurs in the descending order of $Cr_3C_2-20NiCr$, WC-12Co, and WC-20Cr-7Ni, where WC-20Cr-7Ni achieves the highest wear resistance property. It can be inferred that the ratio of the carbide and the binding properties between carbide-binder and binder-binder in a cermet coating material manufactured with HVOF as the primary factors determine the wear properties of the cermet coating material.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.1
• /
• pp.10-16
• /
• 1989

The properties of carburization on Fe-Cr alloys at 900-96$0^{\circ}C$were investiged. The study on carbide layer which had developed during solid-carburizing was made by use of S.E.M, E.PM.A, and X-ray analyzer. The results obtained were summarized as follows, the composition of carbide and the value of activation energy for the growth of carbide layer on each Fe-Cr alloy were 1) Fe-1Cr : M3C and 52Kcal/mole 2) Fe-3Cr and Fe-5Cr : M7C3and 85-88Kcal/mole 3) Fe-7Cr and Fe-9Cr : (M7C3+M23C6)and 55-66Kcal/mole.

• Journal of the Korean Ceramic Society
• /
• v.33 no.2
• /
• pp.223-227
• /
• 1996

The effect of ZrC and VC addition on the diffusion induced recrystallization (DIR) of TiC-Cr3C2 has been investigated. With in creasing the amount of added ZrC to Cr3C2 the DIR of TiC was suppressed at the begining and then occurred. On the contrary the DIR was accelerated with the addition of VC to Cr3C2 Because the lattice parameters of (Ti, Cr)C and (Ti,V)C are smaller and that of (Ti, Zr)C is larger than that of TiC the lattice parameter of (Ti,Cr,Zr)C is expected to be similar to that of TiC,. The results indicate that the strain energy due to lattice mismatch between TiC and solid-solution carbide is the driving force of the observed energy due to lattice mismatch between TiC and solid-solution carbide is the driving force of the observed DIR.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1104-1105
• /
• 2006

Several boride sintered bodies such as $TiB_2$, $ZrB_2$, and $SiB_6$ were previously reported. In the present study, the sinterability and physical properties of chromium boride $(CrB_2)$ containing chromium carbide $(Cr_3C_2)$ sintered bodies were investigated in order to determine its new advanced material. The samples were sintered at desired temperature for 1 hour in vacuum under a pressure by hot pressing. The relative density of sintered bodies was measured by Archimedes' method. The relative densities of $CrB_2$ addition of 0, 5, 10, 15 and 20 mass% $Cr_3C_2$ composites were 92 to 95%. The Vickers hardness of the $CrB_2$ with 10 and 15 mass% $Cr_3C_2$ composites were about 14 and 15 GPa at room temperature, respectively. The Vickers hardness at high temperature of the $CrB_2$ addition of 10 mass% $Cr_3C_2$ composite decreased with increasing measurement temperature. The Vickers hardness at 1273 K of the sample was 6 GPa. The Vickers hardness of $CrB_2$ addition of $Cr_3C_2$ composites was higher than monolithic $CrB_2$ sintered body. The powder X-ray diffraction analysis detected CrB and $B_4C$ phases in $CrB_2$ containing $Cr_3C_2$ composites.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.472-476
• /
• 2001

Type and three-dimensional morphology of carbides precipitated in the X(X= 1.70, 1.92, 2.21, 2.50, 2.86)%C-5%Cr-5%V-5%Mo-5%W-5%Co multi-component white cast iron were investigated using an optical microscope and SEM. The types of carbides precipitated were MC, M$_2$C and M$_{7}$C$_{3}$. Morphology of the MC carbide took three forms, that it petal-like, nodular and coral-like. MC carbide seemed to change its morphology from petal-like through nodular, and finally to coral-like with an increase in carbon content. M7C carbide was classified into lamellar and plate-like type. The lamellar M$_2$C arbide precipitated in the iron with low molybdenum and tungsten contents, and higher contents of both elements in the iron were needed to form the plate-like M$_2$C carbide. The morphology of M$_{7}$C$_{3}$ was rod-like similar to that observed in high chromium white cast iron. However, cobalt does not affect the type and morphology of precipitated carbides.des.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.3
• /
• pp.205-211
• /
• 1996

Structural studies have been performed on precipitation hardening discovered in $Ll_2$-ordered $Ni_3$(Al,Cr) containing 0.2 and 0.5 mol% of carbon in terms of transmission electron microscopy(TEM). By aging at temperatures around 1073 K after solution treatment at 1423 K, fine polyhedral precipitates appear firstly on the dislocations and then in the matrix. The selected area electron diffraction (SAED) studies revealed that these particles are a $M_{23}C_6$ type carbide which has the cube-cube orientation relationship with the matrix lattice. Weak-beam electron microscopy observations of deformation induced dislocations suggested that the dislocations bypass the carbide particles during deformation.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.5
• /
• pp.252-256
• /
• 2014

The TiAlCrSiN film was deposited on the WC-20%TiC-10%Co carbide, and its oxidation behavior was examined at $700-1000^{\circ}C$. It displayed relatively good oxidation resistance owing to the formation of $TiO_2$, $Al_2O_3$, $Cr_2O_3$, and $SiO_2$ up to $900^{\circ}C$. However, at $1000^{\circ}C$, the fast oxidation rate and partial oxidation of WC in the substrate led to the formation of the thick, fragile oxide scale.