• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.62-66
• /
• 2003

Novel coupled line phase shifters and its equivalent phase delay line for compact broadband phased array antennas are proposed. These phase control circuits are designed to be less complex, small size and to use a less number of active devices. The phase shifter is able to control a 120$^{\circ}$ phase shift continuously, and the phase delay line for a reference phase has a fixed 60$^{\circ}$ shifted phase. Both have the low phase error of less than $\pm$3.5$^{\circ}$ and the low gain variations of less than 1 ㏈ within the 300 MHz bandwidth. These proposed circuits are adequate to form the efficient beam-forming networks with compactness, broadband, less complexity, and low cost.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.553-559
• /
• 1994

A coupled microstrip-slot line is analyzed using a full wave method in the specral domain. The characteristics of the coupled microstrip-slot line are obtained based on the Galerkin`s method. The characteristics of even mode by microstrip line and odd mode by slot line are calculated respectively. Especially the singularity of basis function is enforced to be considered with respect of modes. Numerical results are compared with available data and shown good agreement.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.159-165
• /
• 2009

In this study, using a periodical ground structure(PGS) on GaAs monolithic microwave integrated circuit(MMIC), transmission line with a high isolation characteristic was developed for application to compact signal/bias lines of highly integrated MMIC. And the origin of the high isolation characteristic was theoretically investigated. The high isolation characteristic was originated from a resonance between adjacent microstrip lines employing PGS. With only a spacing of $20{\mu}m$, the coupled microstrip line employing PGS showed an isolation value of -47 dB at 60 GHz. The frequency range for high isolation was easily controlled by changing the PGS structure. Above results indicate that microstrip lines employing PGS are very useful for application to compact signal/bias lines of highly integrated MMIC requiring a high isolation characteristics between lines. In addition, equivalent circuit employing closed-form equation for the coupled line with PGS was also extracted.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.40-45
• /
• 2008

In this paper, the exact analysis of the parallel coupled line with open stub and an application to branch-line hybrid are presented. The Z-parameter of the parallel coupled line with an open stub is derived. The structure shows the characteristics as a lowpass filter unit cell(LUC) with wide stop band. Using the characteristics we designed a miniaturized branch-line hybrid with wide harmonic-suppressed band. The size of the new branch-line hybrid is a half of the conventional branch-line hybrid. The frequency response is the same with that of the conventional one near 1.7 GHz center frequency. Including the fifth harmonics, up to 12 GHz spurious responses are suppressed below to -20dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.9B
• /
• pp.1668-1675
• /
• 1999

In this thesis, a narrowband bandpass filter using HTS is proposed for the multiplexer of the satellite communication subsystems. The proposed structure using HTS provides the narrower band and the lower insertion loss characteristics than the conventional parallel-coupled-line bandpass filter. The filter structure using hairpin-line only cause the spurious modes due to the surface waves. But these modes can be lessened by using the hybrid hairpin-line/parallel-coupled-line proposed in this thesis. The narrowband bandpass filters using HTS at the operation frequency of 14.25 GHz are fabricated to have the narrow bandwidth less 1% and the insertion loss less 3dB in comparison with the normal metal microstrip filter with the same three poles. The experimental results show that the filter using HTS has the characteristics of the narrower bandwidth and less insertion loss and can be fabricated with more compact size in comparison with the bandpass filter using normal metal.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2404-2406
• /
• 2000

Chua's circuit is a simple electronic network which exhibits a variety of bifurcation and attractors. The circuit consists of two capacitors, an inductor, a linear resistor, and a nonlinear resistor. In this paper, a transmitter and a receiver using two identical Chua's circuits are proposed and synchronizations of a T or ${\pi}$ type power line are investigated. Since the synchronization of the power line system is impossible by coupled synchronization, theory having both the drive-response and the coupled synchronization is proposed. As a result, the chaos synchronization has delay characteristics in the power line transmission system caused by the line parameters L and C

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.62-65
• /
• 2017

In this paper, three DC Block designs are presented which efficiently meet the need of modern-day compactsize wireless communication systems. As one of the important parts of a complete system design, the proposed microstrip-based DC block with coupled transmission lines efficiently attenuates unwanted frequencies that cause damage to the system. The compact-sized DC block structures are created by incorporating an extended coupled-line section with a radial stub, an enveloped coupled-line section, and using alternate up-down meandering techniques. The structures are analyzed for the L-Band using a high-resistive silicon substrate. At a resonating frequency of 1.575 GHz, the designed DC Block structures have a return loss better than -10 dB, an insertion loss of around -1 dB, and also possess wide pass-band characteristics.

• Journal of Navigation and Port Research
• /
• v.36 no.9
• /
• pp.737-740
• /
• 2012

A miniaturized CMOS bandpass filter for a single RF transceiver system is presented, using diagonally end-shorted coupled lines and lumped capacitors. In contrast to conventional miniaturized coupled line filters, it is proven that the effective permittivity variation of the coupled transmission line has no effect on shifting the center frequency when the bandpass filter is highly miniaturized. A bandpass filter at a center frequency of 2 GHz was fabricated by $0.18{\mu}m$ CMOS technology. The insertion loss with the die area of $1500{\mu}m{\times}1000{\mu}m$ is -5.14 dB. Simulated results are well agreed with the easurements. It also verify the center frequency stability in the compact size bandpass filter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.191-198
• /
• 2007

The electromagnetic coupling between transmission lines in PCB design can degrade the performance of equipment operations. The coupling phenomenon is caused by electromagnetic fields generated by the currents on the transmission lines and the risers. In this paper, an improved method of crosstalk analysis for bent coupled lines on a PCB is proposed and investigated. In the previous cascading method combined with circuit-concept approach, bent coupled lines are devided into sections and each section is represented by ABCD matrix and then they are cascaded. In the proposed method, the crosstalk of bent coupled lines is calculated by the modified circuit-concept approach, where the coupled region is not restricted to the region projected by a generator line on a receptor line but is the total length of receptor line in calculating the forcing terms. Finally, the accuracy of the proposed approach is verified by comparing the calculated results with the measured ones for several bent coupled-line examples.