• Journal of Magnetics
• /
• 제21권4호
• /
• pp.586-592
• /
• 2016

The magnetic-jack type CRDM withdraws or inserts a control rod assembly from/to the reactor core to control the core reactivity. The CRDM housings form not only the path of the electromagnetic field but also the pressure boundary of a nuclear reactor, and a periodic in-service inspection should be carried out if there are welded or flange jointed parts on the pressure boundary. The in-service inspection is a time-consuming process during the reactor refueling, and moreover it is difficult to perform the inspection over the reactor head. A magnetic motor housing is applied for the current SMART CRDM and has several welding joints, however a nonmagnetic motor housing with fewer or no welding joints may improve the operational efficiency of the nuclear reactor by avoiding or simplifying the in-service inspection process. Prior to the development, the magnetic field transfer efficiency of the nonmagnetic housing was required to be assessed. It was verified and optimized by the electromagnetic analysis of the lifting force estimation. Magnetic flux rings were adopted to improve the efficiency. In this paper, the design and optimization process of a nonmagnetic motor housing with the magnetic flux rings for the SMART CRDM are introduced and the analyses results are discussed.

• 열처리공학회지
• /
• 제36권6호
• /
• pp.367-373
• /
• 2023

600 MPa-grade deformed bar samples were manufactured by conventional hot rolling and subsequent Tempcore heat treatment processes. Considering the short-time water quenching step of the Tempcore process for hot-rolled steel, it is inevitable that the temperature profile of the deformed bar depends strongly on its position throughout the sample thickness. As a result, its microstructure can be easily divided into two regions, the surface and the core regions. The former is expected to have a fresh martensite microstructure under rapid cooling conditions, but self-tempering occurs due to the intense heat flow from the hot core region after the process. The latter is generally known to exhibit a mixed microstructure of ferrite and pearlite due to its slow cooling rate. In this study, detailed microstructural evolutions were examined through the thickness direction. The large variation of the microstructure through the thickness direction in the deformed bar samples is partly due to the easy carbon diffusion from the limited additions of alloying elements.

• 지역사회간호학회지
• /
• 제13권4호
• /
• pp.732-742
• /
• 2002

There are few research on the social drinking experience reported by women. Thus, it is necessary to understand the increasing tendency of womens drinking experience in the sociocultural context. This study was aimed to explore and delineate the drinking experience of full-time house wives base don Strauss and Corbin's grounded theory (1998). The subjects of this study were 10 full-time middle-aged house wives who were living in Seoul region. The data were collected through several in-depth interviews and observations until the theoretical saturation was achieved. The data were analyzed using Strauss and Corbin's grounded theory method. The results of this study generated a paradigm that the drinking experience of the full-time middle-aged house wives has a core category of 'free-oneself-from' and is also connected with mingling, anguish, accessibility, reaction of other people, change, personal resources, self-expression and building relationships by drinking. All processes from the occurrence of the central phenomenon to extinction are as follows; 1) Starting the process of the drinking experience for mingling and resolving anguish, and by having an easy accessibility; 2) Perceiving the process of reaction by other people, physical change of herself. and psycho-behavioral change; 3) Experiencing the process of free-oneself from thorough drinking; 4) Acknowledging the process of the resources for free-oneself-from; 5) Selecting the process of self-expression according to the resources; 6) Building the process of the relationship with drinking as a way of self-expression. Based on this paradigm, 4 hypothesis and 4 types are generated. Thus, this study suggests that it is useful to develop nursing interventions to improve the self-esteem of the full-time middle-aged house wives and to provide them various methods of problem solving strategies. This study also proposes that there should be a strategic program for the women so that they could make a route for positive self-expression by achieving a proper relationship with drinking.

• 대한임베디드공학회논문지
• /
• 제17권6호
• /
• pp.375-382
• /
• 2022

This paper proposes a multi-core cooperative computing structure considering the heterogeneous features of automotive embedded on-chip software. The automotive embedded software has the heterogeneous execution flow properties for various hardware drives. Software developed with a homogeneous execution flow without considering these properties will incur inefficient overhead due to core latency and load. The proposed method was evaluated on an target board on which a automotive MCU (micro-controller unit) with built-in multi-cores was mounted. We demonstrate an overhead reduction when software including common embedded system tasks, such as ADC sampling, DSP operations, and communication interfaces, are implemented in a heterogeneous execution flow. When we used the proposed method, embedded software was able to take advantage of idle states that occur between heterogeneous tasks to make efficient use of the resources on the board. As a result of the experiments, the power consumption of the board decreased by 42.11% compared to the baseline. Furthermore, the time required to process the same amount of sampling data was reduced by 27.09%. Experimental results validate the efficiency of the proposed multi-core cooperative heterogeneous embedded software execution technique.

• 한국분말재료학회지
• /
• 제20권1호
• /
• pp.19-23
• /
• 2013

Ru films were successfully prepared by plasma-enhanced atomic layer deposition (PEALD) using $Ru(EtCp)_2$ and $NH_3$ plasma. To optimize Ru PEALD process, the effect of growth temperature, $NH_3$ plasma power and $NH_3$ plasma time on the growth rate and preferred orientation of the deposited film was systemically investigated. At a growth temperature of $270^{\circ}C$ and $NH_3$ plasma power of 100W, the saturated growth rate of 0.038 nm/cycle was obtained on the flat $SiO_2$/Si substrate when the $Ru(EtCp)_2$ and $NH_3$ plasma time was 7 and 10 sec, respectively. When the growth temperature was decreased, however, an increased $NH_3$ plasma time was required to obtain a saturated growth rate of 0.038 nm/cycle. Also, $NH_3$ plasma power higher than 40 W was required to obtain a saturated growth rate of 0.038 nm/cycle even at a growth temperature of $270^{\circ}C$. However, (002) preferred orientation of Ru film was only observed at higher plasma power than 100W. Moreover, the saturation condition obtained on the flat $SiO_2$/Si substrate resulted in poor step coverage of Ru on the trench pattern with an aspect ratio of 8:1, and longer $NH_3$ plasma time improved the step coverage.

• Communications for Statistical Applications and Methods
• /
• 제17권3호
• /
• pp.377-390
• /
• 2010

In the case of time-series analysis, it is often more convenient to rely on the frequency domain than the time domain. Spectral density is the core of the frequency-domain analysis that describes autocorrelation structures in a time-series process. Possible ways to estimate spectral density are to compute a periodogram or to average the periodogram over some frequencies with (un)equal weights. This can be an attractive tool to measure the similarity between time-series processes. We employ the metrics based on a smoothed periodogram proposed by Park and Kim (2008) for the classification of different classes of time-series processes. We consider several lag windows with unequal weights instead of a modified Daniel's window used in Park and Kim (2008). We evaluate the performance under various simulation scenarios. Simulation results reveal that the metrics used in this study split the time series into the preassigned clusters better than do the raw-periodogram based ones proposed by Caiado et al. 2006. Our metrics are applied to an economic time-series dataset.

• 한국자기학회지
• /
• 제20권2호
• /
• pp.61-67
• /
• 2010

근래 첨단 전동기 개발에 고성능 영구자석이 적용됨에 따라 소형 전동기의 고출력화가 가능해진 반면 전동기의 진동과 소음이 커져 그 원인이 되는 코깅 토크에 대한 연구가 필요하게 되었다. 영구자석 전동기의 코깅토크는 영구자석에 의한 자계의 분포에 기인하게 되는데, 전동기의 자계 분포는 코어의 형상에 기인하므로 코어의 형상을 적절하게 설계함으로써 코깅토크를 저감시킬수 있다. 본 논문에서는 영구자석 전동기의 코깅토크를 저감하기 위한 기존의 sub-slot 법을 개선하여 보다 단순화 한 형상으로 코어의 설계변수를 대폭 줄임으로 효과적으로 코깅토크를 저감할 수 있는 기법을 제안하고 이를 영구자석 전동기에 적용하여 기존의 대표적인 sub-slot 법과 비교하고 그 성능을 검증하였다.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2009년도 춘계 종합학술대회 논문집
• /
• pp.17-22
• /
• 2009

다빈치 프로세서는 임베디드 멀티미디어 응용 구현 프로세서로 많이 사용된다. ARM 9 코어 및 DSP 코어의 듀얼 코어로 되어 있어 ARM 코어 에서는 주변 장치 제어, 비디오 입출력 제어, 네트워킹 등을 지원하며, DSP 코어는 보다 효율적인 디지털 신호 처리 연산을 지원한다. 본 논문에서는 본 저자들의 연구실에서 만들고 있는 다빈치 프로세서 기반의 스마트 카메라에 있어서 객체 추적 알고리즘의 최적 구현 방안 노력을 기술한다. 본 논문의 스마트 카메라는 입력 영상에서 관심 객체를 검출하고 이를 추적하며, 분류하고 감시구역에 침입한 경우 이를 IP 프로토콜로 원격 클라이언트에게 통보하는 기능을 보유한다. 객체 추적은 전방 마스크 추출, 전방 마스크 교정, 연결 요소 레이블링, 블롭 지역 계산 등 계산량이 많은 절차들로 구성되어 효율적으로 구현되지 않으면 실시간 처리가 힘들다.

• 대한간호학회지
• /
• 제34권8호
• /
• pp.1416-1426
• /
• 2004

Purpose. The purpose of this study is to identify the role adaptation process experienced by head nurses. Methods. Data were collected from 10 head nurses with in-depth interviews about their actual experiences. All the interviews were recorded and transcribed. The collected data were analyzed by the grounded theory methodology of Strauss and Corbin. Results. The core category was identified as 'weighing and balancing,' and the role adaptation process was divided into six stages by time sequence: inquiring, approaching to others, bringing people into their fold, working with conviction, avoiding conflicts, and settling. Conclusion. The results of this study yield useful information for top mangers of nursing to identify, by stages, the demands of the head nurses in their role adaptation process. The findings of this study contributes to developing programs that facilitates the head nurses' role adaptation.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.139-142
• /
• 1999

Screw rotors are core parts of screw type air compressors, compressors in refrigerating machines and super chargers of automobiles etc. They are composed of a female and a male rotors which have complex section profiles and helically swept geometry. Screw type compressors have advantages of low noise, high efficiency, less needs in maintenance etc. Usually, machining process of screw rotors requires long machining time using CNC machine designed only for screw rotors, which increase the cost of production. In this work, the screw rotors for air-compressors were manufactured with fiber reinforced epoxy composite materials by resin transfer molding process. The mold for the RTM process was made of aluminum and silicon rubber and was designed for release of helical shape products. Composite screw rotors, manufactured by RTM process, have advantages of lightweight, less cost of production, good characteristics of vibration etc.