• Steel and Composite Structures
• /
• v.9 no.2
• /
• pp.89-101
• /
• 2009

This paper presents a simplified model to study post-buckling behaviours of the axially restrained steel column at elevated temperatures in fire. The contribution of axial deformation to the curvature of column section is included in theoretical equations. The possible unloading at the convex side of the column when buckling occurs is considered in the stress-strain relationship of steel at elevated temperatures. Parameters that affect structural behaviours of the axial restrained column in fire are studied. The axial restraint cause an increase in the axial force before the column buckles; the buckling temperature of restrained columns will be lower than non-restrained steel columns. However, the axial force of a restrained column decreases after the column buckles with the elevation of temperatures, so make use of the post-buckling behaviour can increase the critical temperature of restrained columns. Columns with temperature gradient across the section will produce lower axial force at elevated temperatures.

• Journal of the Optical Society of Korea
• /
• v.17 no.5
• /
• pp.371-375
• /
• 2013

To improve the utilization efficiency of solar energy, a new solar optical concentrating system composed of a parabolic reflector with a square cross-section, a hyperbolic reflector with a square cross-section and two converging convex lenses has been designed. The proposed method can simultaneously focus and shape sun light into a square pattern on the solar panel. In addition, the total reflection property of photonic crystal within the range of the visible sunlight spectrum has been analyzed. Finally, the relationship between solar concentrating multiples and the diameter of the primary mirror has been discussed.

• Natural Product Sciences
• /
• v.4 no.1
• /
• pp.15-22
• /
• 1998

'Banafsha' is an important herbal drug of indigenous systems of medicine. Flowers of Viola odornta L. (Violaceae) are considered to constitute the genuine drug 'Banafsha'. However, due to limited distribution of this plant, another species of Viola, i.e. V. pilosa having almost similar medicinal properties, is mostly used under this vernacular instead. Ethnobotanically also different species of Viola i.e. V. odorata, V. pilosa and V. betonicifolia are used for various ailments at different places in our country. In the present study two species of Viola, namely V. pilosa and V. betonictfolia along with the commercial samples of 'Banafsha' were studied and authenticated. It was observed that the market samples procured from Dehradun, Mumbai, Lucknow, Palampur, Ramnagar and Ranikhet showed close resemblance with Viola pilosa in having similar morphological characters like uniseriate hairs on the ovary, geniculate and clavate style, truncate stigma and almost similar TLC profiles. On the other hand the Almora sample was identified as Viola betonicifolia by the presence of large purple flowers, clavate style and convex stigma forming hump like structure. However, the market sample procured from Pathankot was found to be a mixture of two species of Viola namely, V pilosa and V. odorata having dominance of the former species.

• Transactions of Materials Processing
• /
• v.23 no.6
• /
• pp.369-375
• /
• 2014

Flexible roll forming allows profiles to have variable cross-sections. However, the profile may have some shape errors, such as, warping which is a major defect. The shape error is induced by geometrical deviations in both the concave zone and the convex zone. In the current study, flexible roll forming was modeled with FE simulations to analyze the shape error and the longitudinal strain distribution along the flange section over the profile. A distribution of analytically calculated longitudinal strains was used to develop relationships between the shape error and the longitudinal strain distribution as a function of the defined shape parameters for the profile. The FE simulations showed that the shape error is primarily affected by the deviations between the distribution of analytically calculated longitudinal strain and the longitudinal strain distribution of the profile. The results show that the shape error can be controlled by designing the shape parameters to control the geometrical deviations at the flange section in the transition zones.

• Advances in concrete construction
• /
• v.15 no.4
• /
• pp.215-228
• /
• 2023

The vibrational behavior of nanoelements is critical in determining how a nanostructure behaves. However, combining vibrational analysis with stability analysis allows for a more comprehensive knowledge of a structure's behavior. As a result, the goal of this research is to characterize the behavior of nonlocal nanocyndrical beams with uniform and nonuniform cross sections. The nonuniformity of the beams is determined by three distinct section functions, namely linear, convex, and exponential functions, with the length and mass of the beams being identical. For completely clamped, fully pinned, and cantilever boundary conditions, Eringen's nonlocal theory is combined with the Timoshenko beam model. The extended differential quadrature technique was used to solve the governing equations in this research. In contrast to the other boundary conditions, the findings of this research reveal that the nonlocal impact has the opposite effect on the frequency of the uniform cantilever nanobeam. Furthermore, since the mass of the materials employed in these nanobeams is designed to remain the same, the findings may be utilized to help improve the frequency and buckling stress of a resonator without requiring additional material, which is a cost-effective benefit.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.1
• /
• pp.45-53
• /
• 2016

The interaction between the hull of ship and free surface of water generates important loads during slamming motion. In the present study, the slamming load applied on the sectional surface of two-dimensional arbitrary bodies has been investigated under several falling velocities. This simulation has been done with the commercial CFD software ANSYS FLUENT^®. Through the conventional MARINTEK experiments for the benchmark of the simulation, we verified the impact pressure values between the experiments and simulation results. Two arbitrary ship bow section models, Panamax-like(with small convex bulb and flare) and Post panamax-like(with large convex bulb and flare) are also investigated. Simulation results show that a maximum impact pressure on the Post panama-like shape is higher than the Panamax-like shape. According to both a lump of water generated by arbitrary shape and various dead-rise angles of the shape, the pressure picks were enhanced in the simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2382-2388
• /
• 2014

To provide network reliability in indoor wireless communication systems, we should resolve the problem of unexpected network failure rapidly. In this paper, we propose an adaptive resource management (ARM) scheme to support seamless connectivity to users. In consideration of system throughput and user fairness simultaneously, the ARM scheme adaptively determines the set of healing channels, and performs scheduling and power allocation iteratively based on a constrained non-convex optimization technique. Through intensive simulations, we demonstrate the superior performance results of the proposed ARM scheme in terms of the average cell capacity and user fairness.

• Nuclear Engineering and Technology
• /
• v.53 no.5
• /
• pp.1416-1428
• /
• 2021

Pebble flow characteristics can be significantly affected by the configuration of pebble bed, especially for HTGR pebble beds. How to achieve a desired uniform flow pattern without stagnation is the top priority for reactor design. Pebbles flows inside some specially designed pebble bed with arc-shaped contraction configurations at the bottom, including both concave-inward and convex-outward shapes are explored based on discrete element method. Flow characteristics including pebble retention, residence-time frequency density, flow uniformity as well as axial velocity are investigated. The results show that the traditionally designed pebble bed with cone-shape bottom is not the most preferred structure with respect to flow pattern for reactor design. By improving the contraction configuration, the flow performance can be significantly enhanced. The flow in the convex-shape configuration featured by uniformity, consistency and less stagnation, is much more desirable for pebble bed design. In contrast, when the shape is from convex-forward to concave-inward, the flow shows more nonuniformity and stagnation in the corner although the average cross-section axial velocity is the largest due to the dominant middle pebbles.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.77-87
• /
• 1994

This paper deals with an automated forming sequence design system by which designers can determine desirable operation sequences even if they have little experience in the design of cold forging process. The forming sequence design in the cold forging is very important and requires many kinds of technical and empirical knowledge. They system isproposed, which generates forming sequence plans for the multistage cold forging of axisymmtrical solid products. Since the process of metal forming can be considered as a transformation of geometry, treatment of the geometry of the product is a key in planning process. To recognize the geometry of the product section, section entity representation and primitive geometries were used. Section entity representation can be used for the calculation of maximum diameter, maximum height, and volume. Forming sequence for the part can be determined by means of primitive geometries such as cylinder, cone, convex, and concave. By utilizing this geometrical characteristics (diameter, height, and radius), the product geometry is expressed by a list of the priitive geometries. Accordingly the forming sequence design is formulated as the search problem which starts with a billet geometry and finishes with a given product one. Using the developed system, the sequence drawing with all dimensions, which includes the proper sequence of operations for the part, is generated under the environment of AutoCAD. Based on the results of forming sequence, process variables(strain, punch pressure, die inner pressure, and forming load) are determined.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.19-28
• /
• 2021

In rotating detonation engine(RDE), only the detonation wave is moving around the outer wall of the combustor. Neither a mechanical part nor flow is rotating in RDE. Thus, the RDE cross section is not necessary to be circular, but arbitrary closed section is possible. A RDE of tri-arc cross section is designed and As an example of an arbitrary cross sectioned RDE, a RDE of tri-arc cross section is designed in this study, and operational and performance characteristics were examined experimentally. The rotation of the detonation wave is confirmed by dynamic pressure sensor and high-speed camera, while the characteristics of the detonation wave were investigated at the concave and convex surfaces. In the present study, the thrust level of 17.0 N to 96.0 N was obtained depending on the mass flow rate.