• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 추계종합학술대회
• /
• pp.758-761
• /
• 2003

전원장치의 소형화 핵심기술인 반도체 스위칭 기술을 이용하여 단일 전원을 사용하는 소형, 경량화 전자기기에 적합한 5 V/500 mA급 트랜스리스형 파워 모듈(transless type power module)을 설계하였다. 파워 모듈은 강압형 chopper 방식을 이용한 스위칭회로, 제어회로, 전압검출회로, 그리고 정전압 회로 둥으로 구성되어 있으며, 하이브리드-집적회로형(hybrid-IC type)으로 제작되었다. 본 연구에서 설계한 스위칭 레귤레이터 전원회로는 5 V/500 mA급 트랜스리스형 파워 모듈의 전기적 특성을 만족하였다.

• 전력전자학회논문지
• /
• 제3권4호
• /
• pp.418-425
• /
• 1998

본 논문에서는 위상각 제어에서 주어진 턴온 각에서 최대의 토크를 유지하기 위한 적절한 턴오프 각을 자기동조방식(self-tuning method)에 의해 결정하는 방식을 제안하였다. 엔코더에 의해 샘플링 시간(sampling time)동안 구해진 펄스 수는 바로 이전의 샘플링시간 동안 구해진 펄스 수와 비교하여 턴오프 각을 앞으로 또는 뒤로 이동한다. 이러한 과정을 되풀이함으로서 최대 토크를 발생하는 턴오프 각을 결정하게 된다. 실제 회로에서는 원 칩 마이크로프로세서에 의해 처리되었으며 실험을 통해 턴온 각이 변하더라도 자기동조방식에 의해 턴오프 각을 조정하면 빠른 속도가 유지됨을 보여 주었다.

• Journal of Power Electronics
• /
• 제16권2호
• /
• pp.654-665
• /
• 2016

The pumping of electric power from photovoltaic (PV) farms is normally carried out using transformers, which require heavy mounting structures and are thus costly, less efficient, and bulky. Therefore, transformerless schemes are developed for the injection of power into the grid. Compared with the H4 inverter topology, the H6 topology is a better choice for pumping PV power into the grid because of the reduced common mode current. This paper presents how the perturb and observe (P&O) algorithm for maximum power point tracking (MPPT) can be implemented in the H6 inverter topology along with the improved sinusoidal current injected to the grid at unity power factor with the average current mode control technique. On the basis of the P&O MPPT algorithm, a power reference for the present insolation level is first calculated. Maintaining this power reference and referring to the AC sine wave of bus bars, a sinusoidal current at unity power factor is injected to the grid. The proportional integral (PI) controller and fuzzy logic controller (FLC) are designed and implemented. The FLC outperforms the PI controller in terms of conversion efficiency and injected power quality. A simulation in the MATLAB/SIMULINK environment is carried out. An experimental prototype is built to validate the proposed idea. The dynamic and steady-state performances of the FLC controller are found to be better than those of the PI controller. The results are presented in this paper.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1706-1715
• /
• 2016

In this paper, a single phase modified switched-diode topology for both symmetrical and asymmetrical cascaded multilevel inverters is presented. It consists of a Modified Switched-Diode Unit (MSDU) and a Twin Source Two Switch Unit (TSTSU) to produce distinct positive voltage levels according to the operating modes. An additional H-bridge synthesizes a voltage waveform, where the voltage levels of either polarity have less Total Harmonic Distortion (THD). Higher-level inverters can be built by cascading MSDUs. A comparative analysis is done with other topologies. The proposed topology results in reductions in the number of power switches, losses, installation area, voltage stress and converter cost. The Nearest Level Control (NLC) technique is employed to generate the gating signals for the power switches. To verify the performance of the proposed structure, simulation results are carried out by a PSIM under both steady state and dynamic conditions. Experimental results are presented to validate the simulation results.

• KSBB Journal
• /
• 제5권3호
• /
• pp.307-313
• /
• 1990

배양기와 16비트 마이크로컴퓨터를 접속하여 호기성 미생물의 고농도 유가배양시스템을 구성하였다. 기질공급을 위한 제어변수로는 용존산소(DO)를 이용하였다. 용존산소측정기의 출력신호를 컴퓨터에 입력시켜 측정한 DO값에 근거하여 교반모터의 교반속도와 산소유량을 제어함으로써 배양액의 DO를 일정하게 유지하였으며, 연동펌프의 제어에 의해 기질공급을 안정하게 수행하였다. 기질공급의 제어와 DO의 제어를 한가지의 하아드웨어 및 소프트 웨어로 수행할 수 있었다. 제어시스템을 이용하여 메탄올이용균인 Methylobacillus sp. SKI을 유가배양한 결과 배양액의 DO제어와 메탄올 공급의 제어가 무리없이 수행되었으며, 배양 10시간만에 16.53g/l의 균체농도에 도달하였다.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1137-1149
• /
• 2017

In order to reduce the cost, improve the efficiency and simplify the complicated control of existing isolated LED drivers, an improved boundary conduction mode (BCM) Buck ac-dc light emitting diode (LED) driver with extended output voltage and low total harmonic distortion is proposed. With a coupled inductor winding and a stacked output, its output voltage can be elevated to a much higher value when compared to that of the conventional Buck ac-dc converter, without sacrificing the input harmonics and power factor. Therefore, the proposed Buck LED driver can meet the IEC61000-3-2 (Class C) limitation and has a low THD. The operating principle of the topology and the design methodology of the ac-dc LED driver are presented. A 150 W ac-dc prototype was built in the laboratory and it shows that the input current harmonics meet the lighting standard. In addition, the THD is less than 16% at a typical ac input. The peak efficiency is higher than 96.5% at a full load and a normal input.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.43.1-43.1
• /
• 2011

The detail simulation modeling of fully-fed induction generator is investigated through PC based MATLAB/Simulink environment. Generator's stator currents are controlled by indirect vector control method. In this method, generator side converter controls the maximum excitation (air gap flux) by stator d-axis current and controls generator torque by stator q-axis current. Induction generator speed is controlled by tip speed ratio (TSR) upon the wind speed variations in order to generate the maximum output power. The generator torque model is specified as a 3-blade wind turbine with rating, then, the model is simulated under normal operating condition and three different fault conditions. The matlab model designed for fully-fed induction generator based wind farm provides good performance under normal and grid fault conditions. It provides good results for different pwm techniques and fault conditions except the single-phase line to ground fault, which should be verified with real time data from wind farms.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1161-1162
• /
• 2006

본 논문은 3[kW]급 연료전지와 연료전지의 저전압$[40{\sim}60[Vdc]$)을 승압(380vdc)하기 위한 풀-브리지 DC-DC 컨버터, 그리고 승압된 링크전압을 교류 상용전압(220[Vac], 60[Hz)으로 변환하기위한 단상 풀-브리지 인버터로 구성된 연료전지 발전용 전력변환시스템 중 연료전지 시스템용 DC-DC 컨버터를 제안하였다. 제안한 연료전지 시스템용 DC-DC 컨버터는 변압기 2차측에 배전류 정류회로를 삽입하여 기존의 고주파 변압기 보다 간단하면서 무게 및 부피를 줄였다. 그리고 위상 천이 PWM 제어로 출력 전압을 가변시켜 영전압 스위칭을 달성 함으로써 스위칭 손실을 줄였으며. 효율을 95%이상 달성 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1209-1210
• /
• 2006

This paper presents a single phase high power factor PWM boost rectifier featuring soft commutat -ion of the active switches at zero current. It incorporates the most desirable properties of conventional PWM and soft switching resonant techniques. The input current shaping is achieved with average current mode control and continuous inductor current mode. This new PWM converter provides zero current turn on and turn off of the active switches, and it is suitable for high power applications employing IGBT's. The principle of operation, the theoretical analysis, a design example, and experi -mental results from a laboratory prototype rated at 1.6[kW] with 400[Vdc] output voltage are presented. The measured efficiency and the power factor were 96.2[%] and 0.99[%], respectively, with an input current THD equal to 3.94[%], for an input voltage with THD equal to 3.8[%], at rated load.

• 태양에너지
• /
• 제8권2호
• /
• pp.3-11
• /
• 1988

To suppress the natural convection within enclosure spacing it has been shown theoretically and experimentally that the introduction of cell walls will effectively raise the critical Rayleigh number by providing more shear surfaces within the fluid. For a solar collector, a useful solar thermal converter requires effective control of heat losses. It has been reported that the natural convection can be suppressed and the heat performances of the solar collector increased by placing thin, poorly conducting material honeycomb between the absorber plate and the coverglass. The heat performances were measured and compared directly throughout the simultaneous installation of two solar collectors, one with honeycomb structures fabricated from thin poly carbonate sheet and the other without honeycomb structures. Various tilt angles of 30, 45 and 60 deg. from the horizontal and the honeycomb sizes ($W{\times}H$) of $10{\times}10,\;10{\times}20$ and $10{\times}40mm$ were utilized in the present investigation. It is found that the larger the tilt angle are, the greater the heat losses are, and that the smaller the honeycomb size is, the larger suppression effect of heat losses are. Especially, at tilt angles of 30 degree, the heat use ratio of solar collector with the honeycomb sizes of $10{\times}10mm$ improved approximately 29.5% more than that without honeycomb structures.