• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.164-167
• /
• 2000

This paper introduces the design of high-speed analog-to-digital converter for hard disk drive (HDD) read channel. This is based on autozero technique for low-error rate, and Double Speed Dual ADC(DSDA) technique lot efficiently increasing the conversion speed of A/D converter. This An is designed by 6bit resolution, 800M sample/s maximum conversion rate, 390㎽ power dissipation, one clock cycle latency in 0.65 $\mu\textrm{m}$ CMOS technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.800-807
• /
• 2006

To enhance the conversion speed more fast, we separate the determination process of MSB and LSB with the two independent ADC circuits of the Incremental Sigma Delta ADC. After the 1st Incremental Sigma Delta ADC conversion finished, the 2nd Incremental Sigma Delta ADC conversion start while the 1st Incremental Sigma Delta ADC work on the next input. By determining the MSB and the LSB independently, the ADC conversion speed is improved by two times better than the conventional Extended Counting Incremental Sigma Delta ADC. In processing the 2nd Incremental Sigma Delta ADC, the inverting sample/hold circuit inverts the input the 2nd Incremental Sigma Delta ADC, which is the output of switched capacitor integrator within the 1st Incremental Sigma Delta ADC block. The increased active area is relatively small by the added analog circuit, because the digital circuit area is more large than analog. In this paper, a 14 bit Extended Counting Incremental Sigma-Delta ADC is implemented in $0.25{\mu}m$ CMOS process with a single 2.5 V supply voltage. The conversion speed is about 150 Ksamples/sec at a clock rate of 25 MHz. The 1 MSB is 0.02 V. The active area is $0.50\;x\;0.35mm^{2}$. The averaged power consumption is 1.7 mW.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.643-645
• /
• 2013

When you convert word processor files with large amounts of input data to PDF files in on/off line, current PDF conversion solutions do one of the source files to perform the conversion task in the Windows PDF virtual printer environment. Depending on the size of the original PDF file conversion speed to convert PDF to do a large amount of different and if you are performing a very slow speed. When you convert files to PDF in this sequence, depending on the capacity of the original file, PDF conversion rate is different, if automating a mass conversion to the PDF, the speed is very slow. In this paper, the PDF conversion which can use the Windows Terminal Server from one Windows Server when performing a PDF conversion processing of the source file, to create a multi-session Terminal, to perform the PDF conversion process at the same time was studied.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1017-1022
• /
• 2004

This paper presents the conversion speed drive of the cooling tower fans from constant to variable speed. The speed of fan is adjusted using variable speed drives. Since the ambient temperature of cooling tower is varied seasonally, an economic evaluation was performed to determine the potential annual savings. The performances of the proposed technique were observed using cooling tower fans of chemical plant in Thailand as an illustrative case study. The experimental results demonstrating the energy savings fork cooling process and some economic benefits are obtained.

• Journal of KIISE
• /
• v.44 no.5
• /
• pp.537-544
• /
• 2017

As a special form of the signed-digit representation, the NAF(non-adjacent form) minimizes the hamming weight by reducing the average density of the non-zero bits from the binary representation of the positive integer k. Due to this advantage, the NAF is used in various fields; in particular, it is actively used in cryptology. The existing NAF-conversion algorithm, however, is problematic because the conversion speed decreases when the LSB(least significant bit) frequently becomes "1" during the binary positive integer conversion process. This paper suggests a method for the improvement of the NAF-conversion speed for which the problems that occur in the existing NAF-conversion process are solved. To verify the performance improvement of the algorithm, the CPU cycle for the various inputs were measured on the ATmega128, a low-performance 8-bit microprocessor. The results of this study show that, compared with the existing algorithm, the suggested algorithm not only improved the processing speed of the major patterns by 20% or more on average, but it also reduced the NAF-conversion time by 13% or more.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.7
• /
• pp.722-728
• /
• 2005

In this paper, the effects of ethanol blended gasoline on emissions and their catalytic conversion efficiency characteristics were investigated in a multiple-point EFI gasoline engine, The results show that with the increase of ethanol concentration in the blended fuels, THC emissions were drastically reduced by up to thirty percent, And brake specific fuel consumption was increased, but brake specific energy consumption could be improved. However, unburned ethanol and acetaldehyde emissions increased. Pt/Rh based three-way catalysts were effective to reduce acetaldehyde emissions, but had low catalytic conversion efficiency for unburned ethanol. The effect of ethanol on CO and NOx emissions and their catalytic conversion efficiency had close relation to the engine's speed, load and air/fuel ratio. Furthermore fuels blended with thirty percent ethanol by volume could dramatically reduced THC CO and NOx emissions at idle speed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.361-364
• /
• 2008

In this paper, several fields for improving shift quality and mode conversion quality are presented and considered. For a series type hybrid vehicle, improving mode conversion quality is important because it changes its speed with its own motors. A parallel type hybrid vehicle usually has AT or AMT, and its motor and engine can work independently. Therefore, improving both of two qualities is equally important in this case. For a power split type hybrid vehicle, improving mode conversion quality is more important due to the existence of planetary gears which change vehicle's speed.

• 전기의세계
• /
• v.19 no.4
• /
• pp.1-11
• /
• 1970

It is well known that solid-state devices like inverter and converter made by transistor and other semi-conductors are widely used for the purpose of motor speed control in industrial fields. This paper is devoted primarily to a study of Trial Manufacturing of Solid-state Frequency Converter by means of single-phase bridge-type SCR inverter. The principle of the trial product belongs to AC-DC-AC conversion system. The voltage to be impressed to the motor in case of speed control by frequency conversion method is necessary to be proportional to frequency. It also requires the frequency and voltage are independent to hte load variation. In order to meet above requests required to motor speed control., the trial product introduced the open loop system in the frequency setting and closed loop system in the voltage setting. The trial product showed the favorable performance characteristics in speed control of singlephase fractional horsepower motor from 45HZ through 80HZ.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.1
• /
• pp.146-153
• /
• 2015

A model net experiment of the gape net for anchovy in Jindo, Jeollanam-do was carried out to investigate the net shape and hydrodynamic resistance using circulating water channel. The model net was made 1/33 down scale by Tauti's similarity method and the range of experimental current speed was from 0.5 knot to 3.5 knot (increasing 0.5 knot interval). The net mouth height in 0.5 knot of the minimum experiment current speed was shown 26.0 cm (full-scale conversion value 8.58 m). The net mouth height and mouth area in 1.5 knot of the same current speed with a gape net fishing ground were shown 20.0 cm (full-scale conversion value : 6.60 m) and about $507.9cm^2$ (full-scale conversion value : $55.31m^2$). The net mouth height and area were decreased with increase the experimental current speed. The hydrodynamic resistance of the model net in 1.5 knot current speed was shown 1.11 kgf and the value of full-scale conversion by Tauti's method was shown 3.996 ton.

• Journal of information and communication convergence engineering
• /
• v.6 no.4
• /
• pp.439-443
• /
• 2008

It is shown that even if the modulating frequency of the light is too high for direct detection the signal can be extracted by frequency conversion at the same time as the detection by means of the nonlinearity of the APD. When this frequency conversion detection is applied to an optical receiver, the detection bandwidth can be increased while the configuration of the optical detection circuit and the signal processing in the subsequent stages are simplified. A fundamental analysis is carried out with an APD which is confirmed experimentally.