• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.4
• /
• pp.465-473
• /
• 2011

To find the optimum mixing ratio of WGS catalyst with $CO_2$ absorbent for SEWGS process, water gas shift reaction tests were carried out in a fluidized bed reactor using commercial WGS catalyst and sand (as a substitute for $CO_2$ absorbent). WGS catalyst content, gas velocity, and steam/CO ratio were considered as experimental variables. CO conversion increased as the catalyst content increased during water gas shift reaction. Variations of the CO conversion with the catalyst content were small at low gas velocity. However, those variations increased at higher gas velocity. Within experimental range of this study, the optimum operating condition(steam/CO ratio=3, gas velocity = 0.03 m/s, catalyst content=10 wt.%) to get high CO conversion and $CO_2$ capture efficiency was confirmed. Moreover, long time water gas shift reaction tests up to 20 hours were carried out for two cases (catalyst content = 10 and 20 wt.%) and we could conclude that the WGS reactivity at those conditions was maintained up to 20 hours.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.904-907
• /
• 2002

In this study, the plasma-assisted $CO_2$ conversion characteristics were investigated in the streamer corona discharge and silent discharge reactors with dielectric of $Al_2O_3$, to improve the conversion efficiency $CO_2$. Some discharge characteristics of $CO_2$ as parameters of gap spacing and applied voltage frequency, in both corona and silent discharge reactor were also obtained. The maximum $CO_2$ conversion rate was 10.1 [%] under the 5.2 [W] of discharge power and 250 [Hz] of applied voltage frequency.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.2
• /
• pp.96-104
• /
• 2015

Reactivity of commercial WGS catalyst and four new catalysts(RMC-3, PC-73, PC-67SU, PC-59) manufactured with various compositions by Korea Electric Power Research Institute(KEPCO RI) were compared to select suitable WGS catalyst for SEWGS system. Steam/CO ratio, gas velocity, flow rates of syngas, and temperature were considered as operating variables. As a result, commercial catalyst showed the highest CO conversion and RMC-3 catalyst showed also high CO conversion. Therefore, commercial and RMC-3 catalysts were selected as applicable catalysts. However, PC-73 catalyst showed low CO conversion at low temperature($200^{\circ}C$) but showed good reactivity at high temperature($225{\sim}250^{\circ}C$), and therefore, PC-73 catalyst was selected as applicable catalyst for high temperature operation. Continuous operations up to 24 hours for those three catalysts(commercial, RMC-3, PC-73) were conducted to check reactivity decay of catalysts. All three catalysts maintained their original reactivity.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.2
• /
• pp.150-159
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effects of insert geometry and shape of WGS catalysts on CO conversion were measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and WGS catalyst (particle and tablet) and sand were used as bed materials. The parallel wall type and cross type bed inserts were used to hold the WGS catalysts. The CO conversion with steam/CO ratio was determined based on the exit gas analysis. The measured CO conversion using the bed inserts showed high value comparable to physical mixing cases. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. Most of input gas flowed through the catalyst side when we charged tablet type catalyst into the bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. New bed insert geometry was proposed based on the results from this study to enhance contact between input gas and WGS catalyst and $CO_2$ absorbent.

• Current Photovoltaic Research
• /
• v.5 no.4
• /
• pp.122-134
• /
• 2017

As a promising solution to global warming and growing energy demand, photocatalytic $CO_2$ conversion to useful fuels is widely studied to enhance the activity and selectivity of the $CO_2$ photoreduction reactions. In this review, an overview of fundamental aspects of the $CO_2$ reduction photocatalysts is provided. The recent development of the photocatalyst is also discussed, focusing on the mechanisms of light harvesting and charge transfer. Besides, this review sets its sight on inspiring new ideas toward a practical $CO_2$ conversion technology.

• Rapid Communication in Photoscience
• /
• v.2 no.2
• /
• pp.64-66
• /
• 2013

Photoreduction of $CO_2$ into hydrocarbon fuels on the surface of photocatalyst is one of the breakthroughs in the field of photocatalysis. At present various approaches have been investigated with the aim of increasing the $CO_2$ conversion efficiency. The reactor for photoconversion of $CO_2$ plays a vital role in experimental setup. In this work an attempt was made to testify a newly designed the photoreactor for conversion of $CO_2$ into useful products. The photoreactor was specifically designed for simple operation bearing features of temperature and pressure control. The reactor has been tested successively with the standard titania, Degussa P25 yielding methane with moderate production rate of 30.8 $ppm{\cdot}g^{-1}{\cdot}h^{-1}$ under UV lamp with 365 nm wavelength. The methane yield obtained is comparable to the values reported in literature. Thus we anticipate that this experimental setup equipped with newly designed photoreactor can yield competitive amounts of fuels from $CO_2$ photoredcution via 365 nm UV light illumination on various photocatalysts.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.32-39
• /
• 2007

CO oxidation and selective CO oxidation of $La_xCe_{1-x}Co_yCu_{1-y}O_{3-{\alpha}}$ perovskite(x=1, 0.9, 0.7. 0.5; y=1, 0.9, 0.7, 0.5) were investigated. For CO oxidation, catalytic activities were studied according to different preparation conditions such as pH and calcination temperature. The influence of the change of the $O_2$ concentration for selective CO oxidation was studied, too. The substitution of Ce for La improved the catalytic activity for CO oxidation and selective CO oxidation and best activity was observed for $La_{0.7}Ce_{0.3}CoO_3$ prepared at pH 11 and calcined at $600^{\circ}C$. The temperature of 90% CO conversion for CO oxidation using $La_{0.7}Ce_{0.3}CoO_3$ was $230^{\circ}C$. In contrast to the enhancement effect by Ce substitution, the partial substitution of Cu for Co in $LaCo_yCu_{1-y}O_{3-{\alpha}}$ decreased catalytic activities for CO oxidation reaction compared to that using $LaCoO_3$. For selective CO oxidation, the best CO conversion was 66% at $230^{\circ}C$ for $La_{0.7}Ce_{0.3}CoO_3$. The CO conversion of $La_{0.7}Ce_{0.3}CoO_3$ was greatly increased from 66% to 91% as increasing $O_2$ concentration from 1% to 2%.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.1
• /
• pp.91-98
• /
• 1997

Y-zeolite and ${\gamma}$-Al$_2$O$_3$ were used as supports on CO and $C_3$H$_{6}$ oxidation for diesel emission control. The catalysts composed of Pd and Pt as active components were wash coated on honeycomb type ceramic substrate. The oxidation of CO and $C_3$H$_{6}$ was carried out over prepared honeycomb in a fixed bed continuous reactor in the temperature range of 20$0^{\circ}C$~50$0^{\circ}C$ and 20,000 GHSV (h$^{-1}$ ). Surface area of Y-zeolite was larger than that of ${\gamma}$-Al$_2$O$_3$ due to channel structure of Y-zeolite. Therefore, high conversion of CO and $C_3$H$_{6}$ could be obtained because of good dispersion of active metals over Y-zeolite. The honeycomb used Y-zeolite as a support showed higher $C_3$H$_{6}$ conversion than that of ${\gamma}$-Al$_2$O$_3$ due to better cracking and isomerization activity of Y-zeolite. PdPt catalyst showed high conversion of CO and $C_3$H$_{6}$ at low temperature region, 20$0^{\circ}C$~30$0^{\circ}C$, for their synergy effects. PdPt/Y-Zeolite catalyst could achieve more than 80％ conversion of $C_3$H$_{6}$ at 30$0^{\circ}C$. The use of Y-zeolite as a support increased CO and $C_3$H$_{6}$ conversion, and decreased SO$_2$ conversion very effectively. Y-zeolite found to have a good adaptability as a support for the diesel emission after treatment system.

• Resources Recycling
• /
• v.30 no.6
• /
• pp.12-18
• /
• 2021

The water-gas shift reaction is the subsequent step using steam for hydrogen enrichment and H₂/CO ratio-controlled syngas from gasification. In this study, a water-gas shift reaction was performed using syngas from an RPF gasification system. The water-gas shift using a catalyst was performed in a laboratory-scale tube reactor with a high temperature shift (HTS) and a low temperature shift (LTS). The effects of the reaction temperature, steam/carbon ratio, and flow rate on H₂ production and CO conversion were investigated. The operating temperature was 250-400℃ for the HTS system and 190-220℃ for the LTS system. Steam/carbon ratios were between 1.5 and 3.5, and the composition of reactant was CO : 40 vol%, H₂ : 25 vol%, and CO₂ : 25 vol%. The CO conversion and H₂ production increased as the reaction temperature and steam/carbon ratio increased. The CO conversion and H₂ production decreased as the flow rate increased due to reduced retention time in the catalyst bed.

• Clean Technology
• /
• v.25 no.4
• /
• pp.296-301
• /
• 2019

This study was conducted to investigate the characteristics of CO oxidation by NO poisoning in Pt/TiO₂ catalyst prepared by wet impregnation method and calcined at 400 ℃. In order to confirm the NO poisoning effect of the Pt/TiO₂ catalyst, the change of reaction activity was observed when NO was injected during the CO+O₂ reaction where it was ascertained that the CO conversion rate rapidly decreased below 200 ℃. Also, CO conversion was not observed below 125 ℃. Recovery of initial CO conversion was not verified even if NO injection was blocked at 125 ℃. Accordingly, various analyses were performed according to NO injection. First, as a result of the TPD analysis, it was confirmed that NO pre-adsorption in catalyst inhibited CO adsorption and conversion desorption from adsorbed CO to CO₂. When NO was pre-adsorbed, it was confirmed through H₂-TPR analysis that the oxygen mobility of the catalyst was reduced. In addition, it was validated through FT-IR analysis that the redox cycle (Pt²⁺→Pt⁰→Pt²⁺) of the catalyst was inhibited. Therefore, the presence of NO in the Pt/TiO₂ catalyst was considered to be a poisoning factor in the CO oxidation reaction, and it was determined that the oxygen mobility of the catalyst is required to prevent NO poisoning.