• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.233-233
• /
• 2015

We report on a simple method for inducing physical and chemical property-gradient on nanoimprinted patterns by intensity-regulated plasma treatment under caved sample stage. As for the size gradient, a line pattern having a linewidth of 294.9 nm was etched to have gradually varying width from 277.4 nm to 147.9 nm. Modified pattern was proven to be adaptable to replica stamp for reversal patterning. To investigate the wettability gradient, imprinted nanopatterns were coated with fluoroalkylsilane to increase the hydrophobicity, and the surface was modified to have gradually varying wettability from hydrophobic to hydrophilic (contact angle was ${\sim}160^{\circ}$ to ${\sim}5^{\circ}$ on a single chip). This method is expected to be applicable to the selective adsorption of biological entities and hydrodynamic manipulation of liquid droplets for the pumpless microfluidics.

• Journal of Powder Materials
• /
• v.19 no.6
• /
• pp.416-423
• /
• 2012

This paper introduces an effect of a preparing $ZrO_2$-Ag composite on its mechanical properties and microstructure. In present study, $ZrO_2$-Ag was prepared by reduction-deposition route and wetting dispersive milling method, respectively. Two type of Ag powders (nano Ag and micron Ag size, respectively) were dispersed into $ZrO_2$ powder during wetting dispersive milling in D.I. water. Each sample was sintered at $1450^{\circ}C$ for 2hr in atmosphere, and then several mechanical tests and analysis of microstructure were carried out by bending test, hardness, fracture toughness and fracture surface microstructure. As for microstructure, the Ag coated $ZrO_2$ showed homogeneously dispersed Ag in $ZrO_2$ in where pore defect did not appear. However, $ZrO_2$-nano Ag and $ZrO_2$-micro Ag composite appeared Ag aggregation and its pore defect, which carried out low mechanical property and wide error function value.

• Journal of the Korean Society of Industry Convergence
• /
• v.10 no.4
• /
• pp.207-211
• /
• 2007

The durable lifetime of RC structures is shortened by various reasons, which are the generation of cracks in construction and service term, the exterior deterioration according to climatic condition, the surface damage due to chloride attack and the corrosion of reinforced bars. The durability of concrete structures is nevertheless able to be increased by the method and the material of reinforcement and repair. The epoxy resin is widely used for reinforment and repair of concrete because of the superiority in mechanical property, adhesive property, abrasion resistance, impact resistance and chemical resistance. The epoxy cement mortar with hardening agent has a lot of disadvantages that are troublesome mixing work, weakened weatherability and high cost for hardening agent. In this study, the mix proportion of mortar is presented just only with epoxy resin and some admixtures, and the test result of mortar without hardening agent shows the higher strength than the mortar with hardening agent. In the mix proportion, the weight of epoxy resin must be less than 15% of the unit weight of cement, and 10% of unit weight of cement is adequate for the weight of admixtures.

• Membrane Journal
• /
• v.26 no.1
• /
• pp.14-25
• /
• 2016

The membrane separation process is growing very fast because of the high efficiency and low cost compared with other traditional process. The membrane process consists of various components such as membrane, module and mechanical part. The requirements for materials used in the membrane separation are becoming more and more demanding for achievement of high efficiency. Membrane module is also considered as the one of the key component in the membrane system. Recently composite materials have been considered as the membrane housing due to their excellent property and low cost compared with stainless module. In this review, a various types of glass fiber and composite material are summarized and their potential for the application of membrane system is discussed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.5
• /
• pp.80-87
• /
• 2003

Network reconfiguration in distribution systems is realized by changing the status of sectiona1izing switches, and is usually done for loss minimization or load balancing in the system This parer presents an approach for loss minization in distribution systems using reactive tabu search. Tabu search attempts to determine a better solution in the manner of a greatest-descent algorithm, but it can not give any guarantee for the convergence property. Reactive tabu search can give convergence property by using reaction and escape mechanism. Therefore, it can find global optimal solution regardless of initial system configuration. To demonstrate the validity of the proposed algorithm, numerical calculations are carried out the 32 bus system models.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.3
• /
• pp.7-11
• /
• 2015

In order to protect the patterned mask from contamination during lithography process, pellicle has become a critical component for Extreme Ultraviolet (EUV) lithography technology. According to EUV pellicle requirements, the pellicle should have high EUV transmittance and robust mechanical property. In this study, silicon nitride, which is well-known for its remarkable mechanical property, was used as a pellicle membrane material to achieve high EUV transmittance. Since long silicon wet etching process time aggravates notching effect causing stress concentration on the edge or corner of etched structure, the remaining membrane is prone to fracture at the end of etch process. To overcome this notching effect and attain high transmittance, we began preparing a rather thick (200 nm) $SiN_x$ membrane which can be stably manufactured and was thinned into 43 nm thickness with HF wet etching process. The measured EUV transmittance shows similar values to the simulated result. Therefore, the result shows possibilities of HF thinning processes for $SiN_x$ EUV pellicle fabrication.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_2
• /
• pp.669-674
• /
• 2020

Liquid-phase-sintered (LPS) SiC materials were briefly examined with their microstructure and mechanical property. Especially, effect of high-temperature exposure on the tendency of fracture toughness of LPS-SiC were introduced. The LPS-SiC was fabricated in hot-press by sintering powder mixture of sub-micron SiC and sintering additives of Al₂O₃-Y₂O₃. LPS-SiC represented dense morphology and SiC grain-growth with some amount of micro-pores and clustered additives as pore-filling. The strength of LPS-SiC might affected by distribution of micro-pores. LPS-SiC tended to decrease fracture toughness depending on increasing exposure temperature and time.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.5
• /
• pp.525-530
• /
• 2021

The purpose of this study was to investigate the effect of spherodizing heat treatment holding time on the microstructure and mechanical properties of the accelerated cooling-treated API X70 steel, which is mainly used as a structural material for line pipe steel for natural gas pipes. The accelerated cooling-treated API X70 steel was spherodizing treated at 700℃ for 12~48 h. The microstructure was observed using an OM and a FEG-SEM, and mechanical properties were obtained by tensile test. The microstructure of the API X70 steel was banded in the hot rolling direction, and the polygonal ferrite(PF) adjacent to pearlite(P) has mainly a fine size, and coarse PF and fine acicular ferrite were formed in the middle of P and P. As the spherodizing treatment time increased, the number of carbide particles decreased and its distribution interval increased, and the ferrite grain size was coarsened. The tensile strength decreased and the ductility increased with spherodizing treatment time, and the yield point elongation was disappeared in a stress-strain curve after the spherodizing treatment.

• Journal of the Korean earth science society
• /
• v.40 no.4
• /
• pp.428-435
• /
• 2019

In the shallow coastal area, located off the northwestern Taean Peninsula of the eastern Yellow Sea, geoacoustic models with two layers were reconstructed for underwater acoustic experimentation and modeling. The Yellow Sea experienced glacio-eustasy sea-level fluctuations during Quaternary period. Coastal sedimentation in the Yellow Sea was characterized by alternating terrestrial and shallow marine deposits that reflected the fluctuating sea levels. The coastal geoacoustic models were based on data from piston, grab cores and the high-resolution 3.5 kHz, chirp seismic profiles (about 70 line-kilometers, respectively). Geoacoustic data of the cores were extrapolated down to 3 m in depth for geoacoustic models. The geoacoustic property of seafloor sediments is considered a key parameter for modeling underwater acoustic environments. For simulating actual underwater environments, the P-wave speed of the models was adjusted to in-situ depth below the sea floor using the Hamilton method. The proposed geoacoustic models could be used for submarine acoustic inversion and modeling in shallow-water environments of the study area.

• Journal of the Korean Mathematical Society
• /
• v.55 no.4
• /
• pp.833-848
• /
• 2018

In this paper we study the existence of conditional expectation for closed and convex valued Pettis-integrable random sets without assuming the Radon Nikodym property of the Banach space. New version of multivalued dominated convergence theorem of conditional expectation and multivalued $L{\acute{e}}vy^{\prime}s$ martingale convergence theorem for integrable and Pettis integrable random sets are proved.