• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.1
• /
• pp.69-74
• /
• 2010

In a grid connected variable speed wind turbine, the PCC voltage and the wind power fluctuate as the wind velocity changed. And this voltage variation is changed due to location of PCC. This paper calculate the value of PCC voltage variation which is proportional to the product of the line impedance from the ideal generator to the PCC and the wind turbine output current. And to reduce this PCC voltage variation, this paper calculate the required reactive power analytically using the vector diagram method. Output reactive current is changed, if the reactive current is limited by inverter capacity or grid code have the margin of voltage variation. If the grid connected inverter is controlled by proposed algorithm, the PCC voltage variation is minimized though the wind turbine output change at random. To verify calculated voltage variation and required reactive power, this paper utilized Matlab and PSCAD/EMTDC simulation and real small wind turbine and power system in Sapsido, island in the Yellow Sea.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.3
• /
• pp.190-198
• /
• 2016

Application of fuel cell to produce renewable energy for commercial purpose is limited by the high cost of Pt based electrode materials. Development of inexpensive, high energetic electrode is the need of the hour to produce pollution free energy using bio-fuel through a fuel cell. Ni-Cu and Ni-CeO₂-Cu electrode materials, electro synthesized by pulse current have been developed. The surface morphology of the electrode materials is controlled by different deposition parameters in order to produce a high current from the electro-oxidation of the fuel, the ethanol. The developed materials are electrochemically characterized by Cyclic Voltammetry (CV), Chronoamperometry (CA) and Potentiodynamic polarization tests. The results confirm that the high current is due to their enhanced catalytic properties viz. high exchange current density (i₀), low polarization resistance (R_p) and low impedance. It is worthwhile to mention here that the addition of CeO₂ to Ni-Cu has outperformed Pt as far as the high electro catalytic properties are concerned; the exchange current density is about eight times higher than the same on Pt surface. The morphology of the electrode surface examined by SEM and FESEM exhibits that the grains are narrow and sub spherical with 3D surface, containing vacancies in between the elongated grains. The fact has enhanced more surface area for electro oxidation of the fuel, giving rise to an increase in current. Presence of Ni, CeO₂, and Cu is confirmed by the XRD and EDXS. Fuel cell fabricated with Ni-CeO₂-Cu material electrode is expected to produce clean electrical energy at cheaper rates than conventional one, using bio fuel the derived from biomass.

• Restorative Dentistry and Endodontics
• /
• v.13 no.2
• /
• pp.265-282
• /
• 1988

The pulp response of posterior composite resins in relation to the thickness of remaining dentin was studied with 120 teeth from 6 dogs, Class V. cavities were prepared on the cervical area of facial surfaces. The thickness of remaining dentin was controlled with Caries Meter$^{(R)}$. The cavities of group A were prepared to show the electrical impedance of 22-26$K{\Omega}$(thickness of remaining dentin:0.4-0.5mm). The cavities of group B, 50-55$K{\Omega}$(thickness of remaining dentin: 0.8-0.9mm). Zinc - Oxide Eugenol cement, Estilux$^{(R)}$ posterior, Heliomolar$^{(R)}$ radiopaque, P-30$^{(R)}$ and Scotchbond$^{(R)}$+P-30$^{(R)}$ were filled in each cavity. After 3days, 1 week, 2 weeks, 4 weeks, 9 weeks and 13 weeks, the teeth and pulp tissue were processed routinely and stained with Hematoxylin and Eosin. Pathological tissue changes were observed with light microscope. The following results were obtained. I. The pulp response of group A cavties was severer than that of group B cavities. 2. In the pulp of group A cavities which were filled with Zinc-Oxide Eugenol Cement, only vascular changes were observed after 3 days and 1 week, severe acute inflammation after 4 weeks, moderate acute inflammation after 9 weeks, and chronic inflammation and formation of granulation tissue after 13 weeks. 3. In the pulp of group A cavities which were filled with Estilux$^{(R)}$ posterior, only vascular changes were observed after 3 days and 1 week. But the inflammatory response has became much severer with the elapsed experimental period. 4. In the pulp of group A cavities which were filled with Heliomolar$^{(R)}$ radiopaque, the inflammatory response with the elapsed experimental period was not severer than that of the pulp of group A cavities which were filled with other materials. 5. In the group B cavities, the difference of pulp response by filling materials was not recognizable. In the group A cavities, the pulp response of Estilux$^{(R)}$ posterior was severest and in order P-30$^{(R)}$, Heliomolar$^{(R)}$ radiopaque was slighter.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.141-145
• /
• 2000

Anodically Polymerized conducting Polypyrrole film electrode was employed to Pick up uranyl ion with the type of Gr/ppy, xylenol orange modified electrode. To have Porous and oriented ppy film, NBR was applied as precoating agent. The rate constant of polymerization was $3.22\times10^{-3}s^{-1}$ which was 1.6 times smaller value than bare graphite surface. The deposited amount of uranyl iou on $1.70Ccm^{-2}$ of ppy was $1.55\times10^{-4}g$. The matrix effect in artificial seawater was $6.8\%$. The polymer film electrode has a diffusion controlled process in conduction, but the modified Gr/ppy, $X.O^{4-}UO^+$ type was influenced on the ion doping and electronic conduction of film itself owing to increasing of impedance. The capacitance of electrical double layer was respectively enhanced to 56 and 130 times in Gr/ppy, $X.O.^{4-}$ and Gr/ppy, $X.O^{4-}UO^+$ than Grippy type electrode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.335-344
• /
• 2004

A low phase noise EQM(Engineering Qualified Model) LO(Local Oscillator) has been developed for Ka-band satellite transponder. A VCDRO(Voltage Controlled Dielectric Resonator Oscillator) is also designed using a high impedance inverter coupled with dielectric resonator to improve the phase noise performances out of the loop bandwidth. The mechanical analysis fur housing and the thermal analysis fur circuit board are achieved. This EQM LO is applied to Ka-band satellite transponder of EQM level after environmental experiments for space application. The LO has the harmonic suppression characteristics above 52 ㏈c and requires low power consumption under 1.3 watts. The phase noise characteristics are exhibited as -101.33 ㏈c/㎐ at 10 ㎑ offset frequency and -114.33 ㏈c/㎐ at 100 ㎑ offset frequency, with the output power of 14.0 ㏈m${\pm}$0.17 ㏈ over the temperature range of -15∼＋65$^{\circ}C$.

• KIPS Transactions on Computer and Communication Systems
• /
• v.3 no.9
• /
• pp.273-278
• /
• 2014

Recent use of electricity during peak hours electricity supply-demand imbalance is inevitable that limit power use force. Therefore, in this paper, a circuit of parallel power operation equipment for peak power reduction which saves the power to electricity storage device during the non-peak power time and supply from the storage power during the expected power shortages time is designed Through this circuitry, the peak power of the commercial power supply with the parallel operation and connection of the commercial power supply and the power supply of the inverter from electricity storage that is a key feature of PRS(Peak power Reduction System) can be controlled. In addition, in order to increase the efficiency, a Transless Power Circuit DC-AC inverter is developed. Moreover, a variable impedance control is applied to the storage of electric power of an Uninterruptible Power Supply associated with a commercial power source.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.54-61
• /
• 2007

A variable gain low noise amplifier (VG-LNA) implemented in TSMC 0.18 um process is presented. This VG-LNA is designed of two stage amplifier, and its gain is controlled by the shunt feedback loop composed of a gain control transistor (GCT) and a coupling capacitor in second stage. The channel resistance of GCT in the shunt feedback loop influences the input and output stages of a second stage by the Miller effect. Total gain of the proposed VG-LNA is changed by two factors, the load impedance reduction and the interstage mismatch by controlling the channel resistance of the GCT. Consequently, by adding a shunt feedback with a gain control transistor, this proposed VG-LNA achieves both wide gain tuning range of 37 dB and continuous gain control simultaneously.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.268-272
• /
• 2003

The microstructures of tungsten films were controlled by changing the sputtering pressure and substrate temperatures during D.C. sputter deposition. As the sputtering pressures were decreased, the sputtered models of the tungsten films were changed from the zone I model to zone T model. The tungsten film having zone T model microstructure shows a resistivity of 10${\times}$10$\^$-6/ $\Omega$-cm and (110) preferred orientation. FBAR with Bragg reflector composed of $SiO_2$and tungsten films having zone T model microstructure shows quality factor, Q$\_$s/, of 494 and K$\_$eff/$\^$2/ of 5.5% due to the high acoustic impedance and the smooth surface.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.2
• /
• pp.173-183
• /
• 2010

In a split beam echo sounder, the transducer design needs to have minimal side lobes because the angular position and level of the side lobes establishes the usable signal level and phase angle limits for determining target strength. In order to suppress effectively the generation of unwanted side lobes in the directivity pattern of split beam transducer, the spacing and size of the transducer elements need to be controlled less than half of a wavelength. With this purpose, a 50 kHz tonpilz type transducer with a half-wavelength diameter in relation to the development of a split beam transducer was designed using the equivalent circuit model, and the underwater performance characteristics were measured and analyzed. From the in-air and in-water impedance responses, the measured value of the electro-acoustic conversion efficiency for the designed transducer was 51.6%. A maximum transmitting voltage response (TVR) value of 172.25dB re $1{\mu}Pa/V$ at 1m was achieved at 52.92kHz with a specially designed matching network and the quality factor was 10.3 with the transmitting bandwidth of 5.14kHz. A maximum receiving sensitivity (SRT) of -183.57dB re $1V/{\mu}Pa$ was measured at 51.45kHz and the receiving bandwidth at -3dB was 1.71kHz. These results suggest that the designed tonpilz type transducer can be effectively used in the development of a split beam transducer for a 50kHz fish sizing echo sounder.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.2
• /
• pp.223-230
• /
• 2019

A facile method for surface coating with $Li_2TiF_6$ which has a high lithium-ion conductivity, on $LiMn_2O_4$ spinel cathode material for high performance lithium ion batteries. The surface coating is performed by using a co-precipitation method with $Li_2CO_3$ powder and $H_2TiF_6$ solution under room temperature and atmospheric pressure without special equipment. Total coating amount of $Li_2TiF_6$ is carefully controlled from 0 to 10 wt.% based on the active material of $LiMn_2O_4$. They are evaluated by a systematic combination of analyses comprising with XRD, SEM, TEM and ICP. It is found that the surface modification of $Li_2TiF_6$ is very beneficial to high cycle life and excellent rate capability by reducing surface failure and supporting lithium ions transportation on the surface. The best coating condition is found to have a high cycle life of $103mAh\;g^{-1}$ at the 100th cycle and a rate capability of $102.9mAh\;g^{-1}$ under 20 C. The detail electrochemical behaviors are investigated by AC impedance and galvanostatic charge and discharge test.