• 열처리공학회지
• /
• 제13권5호
• /
• pp.346-354
• /
• 2000

Effect of Nb addition on the phase transformation behavior was studied through continuous cooling transformation tests after reheating(reheating CCT) and deforming(deforming CCT) the 0.07%C-1.3%Mn-0.015%Ti-(0~0.08)% Nb steels. Transformation temperatures for deforming CCT were lower than those for reheating CCT, and the critical cooling rate for bainite transformation during deforming CCT was lower than that during reheating CCT. These enhanced hardenability for deforming CCT was considered to come from the sufficient solid solution of Nb in austenite during high temperature reheating before deformation. With Nb addition, the phase transformation temperature decreased, the bainite formation was enhanced, and the hardness of steel increased. Furthermore, these phenomena were more remarkable for deforming CCT than for reheating CCT. From the results, Nb-Ti bearing low carbon steel was considered to be a very favorable alloy system with good strength/toughness balance by recrystallization control rolling process.

• 열처리공학회지
• /
• 제17권5호
• /
• pp.283-292
• /
• 2004

The effects of the annealing parameters on microstructures were examined in a cold-rolled high strength steel containing 0.1% C, 0.5% Si, 1.5% Mn, and 0.04% Nb. It was impossible to avoid martensite in the microstructure even though the continuous annealing parameters were controlled. This indicates that the alloying elements such as silicon and manganese contributing to manganese equivalent($Mn_{eq}$) should be reduced to produce the ferrite-pearlite microstructure for the solid solution and precipitation hardened steel. It was found that a decrease in the rapid cooling temperature to $520^{\circ}C$ was effective to change the microstructure from ferrite-martensite to ferrite-pearlite-martensite. Typical dual-phase properties exhibiting a low yield ratio and a continuous yielding behavior were obtained when the rapid cooling temperature was in the range of $680^{\circ}C$ to $600^{\circ}C$. The critical volume fraction of martensite for the typical properties of dual-phase steel was about 11 percent.

• 멤브레인
• /
• 제14권3호
• /
• pp.218-229
• /
• 2004

SPG (Shirasu porous glass) 관형 막이 설치된 회분식 막유화 장치를 사용하여 단분산 칼슘 알지네이트 미립자를 제조하기 위한 막유화 공정변수의 최적조건을 결정하였다. 막유화의 공정변수로는 연속상에 대한 분산상의 비율, 알지네이트 농도, 유화제의 종류와 농도, 안정제 농도, 가교제 농도, 교반속도, 막간 압력차 및 SPG 막의 세공크기로 설정하고, 이들 변수가 제조된 알지네이트 미립자의 입자 크기와 분포에 미치는 영향을 검토하였다. 막유화의 공정변수들 중에서 연속상에 대한 분산상의 비율, 막간 압력차 그리고 알지네이트 농도가 증가할수록 미립자의 크기가 증가하였다. 반면 유화제의 농도, 교반속도 그리고 가교제의 농도가 증가할수록 미립자의 크기가 감소하였다. 세공 크기 $2.9{\mu}\textrm{m}$인 SPG막을 사용한 경우 막유화의 공정변수 조절을 통해 최종적으로 평균 입자 크기 $6{\mu}\textrm{m}$, 크기 분산도 1.1인 단분산 알지네이트 미립자의 제조가 가능하였다.

• 멤브레인
• /
• 제31권1호
• /
• pp.52-60
• /
• 2021

SPG (Shirasu porous glass) 원통형 막을 회전 시키는 회전 막유화를 사용하여 칼슘 알지네이트 미소 구체를 제조할 때, 단분산 미소 구체를 제조하기 위한 회전 막유화 공정변수들의 최적 조건을 결정하였다. 회전 막유화의 공정 변수로는 막의 회전 속도, 막간 압력차, 연속상에 대한 분산상의 비율, 알지네이트 농도, 유화제의 농도, 안정제 농도, 가교제 농도 및 막의 세공 크기를 설정하고, 이들 변수로 제조된 알지네이트 미소 구체의 크기와 단분산성에 미치는 영향을 검토하였다. 이 결과 회전 막유화의 공정 변수들 중에서 막모듈의 회전 속도, 유화제의 농도, 가교제의 농도가 증가 할수록 미소 구체의 크기가 감소하였으며, 반면에 연속상에 대한 분산상의 비율, 막간 압력차, 알지네이트 농도가 증가할수록 미소 구체의 크기가 증가하였다. 세공 크기 3.2 ㎛인 SPG막을 사용한 회전 막유화에서 공정변수 조절을 통해 최종적으로 입자 크기가 4.5 ㎛의 단분산 알지네이트 미소 구체의 제조가 가능하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1225-1228
• /
• 2004

We have studied the Polymer Stabilized Continuous Director Rotation (PSCDR) mode to solve the thermal shock problem which is core and main problem in CDR mode. The cell filled 95wt. % R2301 FLC and 5wt. % UCL-001 polymer is applied a low DC voltage only near the phase transition temperature from cholesteric to chiral smectic C phase transition to get defect-free alignment. In the previous work, we also confirmed layer deformation induced by an applied DC field only near the phase transition temperature from Ch to $SmC^{\ast}$. Results of layer structure, and characteristics of electro-optical properties between CDR and PSCDR mode will be discussed in this paper. We are also in progress to finalize the layer structures compared between CDR and PSCDR mode by x-ray measurements.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2004년도 임시총회 및 추계학술발표회
• /
• pp.89-92
• /
• 2004

The influence of a single fracture intersection on density-driven immiscible flow is compared between wetting (water into air) and nonwetting (Trichloroethylene into water) flows. At low supply rates, the intersection acted as a hysteretic gate to pulsed flow of the wetting phase, but had minimal influence on nonwetting phase flow. For both cases, increasing the supply rate led to the formation of continuous fluid tendrils that crossed the intersection without interruption. The wetting experiment returned to pulsed flow as the supply rate was decreased, while the nonwetting experiment maintained a continuous flow structure. Results suggest a fundamental difference between wetting and nonwetting phase flows in fracture network.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.971-982
• /
• 2015

In order to improve the quality of the billet continuous casting, a two-phase orthogonal power supply (TPOPS) for electromagnetic stirrer is researched, which is composed of three-phase PWM rectifier and three-leg inverter. According to the power analysis of system, the ripple of dc-link voltage is analyzed and its analytical expression is derived. In order to improve the performance of electromagnetic stirring, an integrated control method with feedforward control is proposed for PWM rectifier to suppress the fluctuations of dc-link voltage and provide a stable dc source for inverter. According to the simplified equivalent model, a composite current control method is proposed for inverter. This proposed method can combine the merits of feedforward control with feedback control to effectively improve the dynamic output performance of TPOPS. Finally, a 300kVA prototype of TPOPS is developed, and the results have verified the analysis and control method.

• 대한기계학회논문집B
• /
• 제28권5호
• /
• pp.587-593
• /
• 2004

In this paper, flow characteristics of plasma flow in a micro-tube were investigated experimentally using micro particle image velocimetry(micro-PIV). For comparison, the experiments were repeated for deionized(DI) wale. instead of plasma. Both velocity profiles of plasma and do-ionized water are well agreed with the theoretical velocity distribution of newtonian fluid. We also carried out generating plasma-in-oil droplet formation at a Y-junction microchannel. In order to clarify the hydrodynamic aspects involved in plasma droplet formation, Rhodamine-B were mixed with plasma only for visualization of plasma droplet. With oil as the continuous phase and plasma as the dispersed phase, plasma droplet can be generated in a continuous phase flow at a Y-junction. For given experimental parameters, regular-sized droplets are reproducibly formed at a uniform flow conditions.

• 대한전기학회논문지
• /
• 제36권1호
• /
• pp.52-57
• /
• 1987

In this paper, a methodology is developed to remove the reaching phase and the high frequency chattering phenomenon which are the common drawbacks of variable structrue control (VSC) system. A time varying switching surface is proposed to achieve sliding motion during the entire control process and a continuous control law whose terms are continuous functions inside a boundary layer neighbouring the time varying switching surface is developed to remove the high frequency chattering phenomenon of VSC. The methodology developed in this paper is applied to the 2'nd order time varying system and the simulated results are compared with those of typical VSC methodology.

• 한국전산유체공학회지
• /
• 제12권4호
• /
• pp.44-53
• /
• 2007

A three-dimensional (3D) unstructured hydrodynamic solver for transient two-phase flows has been developed for a 3D component of a nuclear system code and a component-scale analysis tool. A two-fluid three-field model is used for the two-phase flows. The three fields represent a continuous liquid, an entrained liquid, and a vapour field. An unstructured grid is adopted for realistic simulations of the flows in a complicated geometry. The semi-implicit ICE (Implicit Continuous-fluid Eulerian) numerical scheme has been applied to the unstructured non-staggered grid. This paper presents the numerical method and the preliminary results of the calculations. The results show that the modified numerical scheme is robust and predicts the phase change and the flow transitions due to boiling and flashing very well.