• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1168-1177
• /
• 2015

This paper presents a scheme to improve the line current distortion of power factor corrector (PFC) topology at the zero crossing point using a predictive control algorithm in both the continuous conduction mode (CCM) and discontinuous conduction mode (DCM). The line current in single-phase PFC topology is distorted at the zero crossing point of the input AC voltage because of the characteristic of the general proportional integral (PI) current controller. This distortion degrades the line current quality, such as the total harmonic distortion (THD) and the power factor (PF). Given the optimal duty cycle calculated by estimating the next state current in both the CCM and DCM, the proposed predictive control algorithm has a fast dynamic response and accuracy unlike the conventional PI current control method. These advantages of the proposed algorithm lower the line current distortion of PFC topology. The proposed method is verified through PSIM simulations and experimental results with 1.5 kW bridgeless PFC (BLPFC) topology.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.86-90
• /
• 2014

A DC-DC Converter operates in CCM(Continuous Coundcution Mode), DCM(Discontinuous Conduction Mode), CRM(Critical Conduction Mode). The CRM is boundary between CCM and DCM. If a DC-DC converter is designed to operate in CRM, its inductor volume can decrease and power loss which caused by switch and diode can decrease. In this paper, the DC-DC converter which operates in CRM is applied to a solar array regulator(SAR) for the satellite. The switching frequency of the CRM boost SAR changes according to input and output condition. The switching frequency limit logic is applied to limit the maximum switching frequency. Meanwhile, the small signal transfer function of the CRM boost SAR is simple, so the controller design is also simple. In this paper, the small signal transfer function from control reference to solar array voltage is induced. And the voltage controller is designed based on the small signal transfer function. Finally, the CRM boost SAR is verified by simulation.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.323-331
• /
• 2018

Buck power factor correction (PFC) converters, compared with conventional boost PFC converters, exhibit high efficiency performance in the entire range of universal line voltage. This feature has gotten more attention for eliminating the zero crossing dead angle of buck PFC rectifiers. Furthermore, bridgeless structures for the reduction of conduction losses have been proposed. The aim of this paper is to introduce a single-phase buck rectifier that simultaneously has unity power factor (PF) and bridgeless structure while operating in the continuous conduction mode (CCM). For this purpose, two auxiliary flyback converters without any active switches are applied to a bridgeless buck rectifier to eliminate the zero crossing dead angle and achieve unity power factor, low total harmonic distortion (THD) and high efficiency. The operation and design considerations of the proposed rectifier are verified on a 150W, 48V prototype using a conventional peak-current-mode control. The measurement results show that the proposed rectifier has nearly unity power factor, THD less than 7% and high efficiency.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.330-337
• /
• 1998

A duty cycle average model is mathematically developed for an average model of buck converter employing hysteresis c control. The derived model is able to simultaneously deal with both the continuous conduction mode (CCM) and the d discontinuous conduction mode (DCM) in the time domain. Also. taking advantage of the MAST language of SABER. a t template of the proposed duty cycle average model is built for the time and frequency domain analyses. The accuracy of t this template is verified through the computer simulations.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1861-1868
• /
• 2016

In this paper, a three-phase AC-DC high step-up converter is developed for application to microscale wind-power generation systems. Such an AC-DC boost converter prossessess the property of the single-switch high step-up DC-DC structure. For power factor correction, the advanced half-stage converter is operated under the discontinuous conduction mode (DCM). Simulatanously, to achieve a high step-up voltage gain, the back half-stage functions in the continuous conduction mode (CCM). A high voltage gain can be obtained by use of an output-capacitor mass and a coupled inductor. Compared to the output voltage, the voltage stress is decreased on the switch. To lessen the conducting losses, a low rated voltage and small conductive resistance MOSFETs are adopted. In addition, the coupled inductor retrieves the leakage-inductor energy. The operation principle and steady-state behavior are analyzed, and a prototype hardware circuit is realized to verify the performance of the proposed converter.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.261-263
• /
• 2018

본 논문에서는 다수의 고주파 단상 변압기를 사용하여 다수의 독립된 직류 전압원을 만들 수 있는, 여러 다이오드 정류기와 연결된 풀 브릿지 DC-DC 컨버터에 대한 분석 및 제어 기법을 제안한다. 본 토폴로지의 경우 제어 대상인 2차단 직류단이 다수이지만 1차단 스위칭 회로가 하나의 풀 브릿지 회로이기 때문에 2차단 전압의 개별 제어를 위한 자유도가 부족하다. 이에 따라 다수 직류단 전압의 평균 값을 제어하는 방식이 사용된다. 이때, 각 직류단에 다른 용량의 부하가 연결되어 있는 상황에 대하여 상세한 분석이 필요하다. 본 논문에서는 제시된 토폴로지(Topology)를 하드 스위칭 기반의 DCM(Discontinuous Conduction Mode) 및 CCM(Continuous Conduction Mode) 동작의 경우에 대해 분석한다. 이를 바탕으로, 직류단 전압 제어를 위한 전향 보상 및 안티 와인드업을 포함하는 Integral and Proportional (IP) 제어기를 구성하고, 제어기 이득 및 전향 보상을 수식화 한다. 최종적으로 구해지는 제어기의 전달 함수를 통해, 제어기가 정확하게 설계되었는지 컴퓨터 시뮬레이션으로 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.4
• /
• pp.297-304
• /
• 2013

This paper presents a improved control technique to overcome disadvantage when the inductor current of boost converter in PV system becomes DCM(Discontinuous Conduction Mode) due to the low insolation. MPPT(Maximum Power Point Tracking) output reference voltage could not be exactly followed by conventional dual-loop PI control method used typically because of the error between the actual current and measured current. Therefore, in this paper, Hybrid controller that changes the control method in DCM and CCM(Continuous Conduction Mode), and single state feedback controller are used to compensate that problem. The proposed control technique was verified by simulation using PSIM 9.0 and experiments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.4
• /
• pp.601-610
• /
• 2016

The light-emitting diode (LED) has been used in a variety of industrial fields and for general 0lighting purposes on account of its high efficiency, low power consumption and long lifespan. The LED is driven by direct current; therefore, an AC/DC converter is typically required for its use. An electrolytic capacitor is generally used for stabilizing DC voltage during use of the AC/DC converter. However, this capacitor has a short lifespan, which makes it a limiting factor in LED lighting. Furthermore, LED lighting requires a dimmable control to enable energy savings and fulfil a growing consumer demand. In this paper, the dimmable single-stage power factor correction (PFC) continuous conduction mode (CCM) flyback converter that employs no electrolytic capacitor is presented. The LC resonant filter is alternatively applied to reduce the 120[Hz] ripple on the output. And the optimum value of the LC resonant filter parameters considering both efficient and performance is analysed. Simulation and experimental results verify the satisfactory operation of the converter.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.4
• /
• pp.586-592
• /
• 2016

The current control of Continuous Conduction Mode(CCM) can be implemented by several methods: peak current control; average current control; and hysteresis control. Among these methods, the hysteresis current control is popularly applied in various converter applications because of its simplicity of implementation, fast current control response and inherent peak current limiting capability. However, a current controller with conventional hysteresis band which multiplies the current reference has the disadvantage that the modulation frequency varies in one cycle of the input voltage and, as a result, generates high switching frequency in the low input voltage section. Also it is complicated to design the input filter due to varying switching frequency. This paper proposed an optimum hysteresis-band current control method where the band is generated by using both multiplication method and sum method to maintain the modulation frequency to be nearly constant. This approach can solve the high switching frequency in the low input voltage section, and achieve easy design of input filter. The performance of the proposed converter is verified with the simulation and the experimental works.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.12
• /
• pp.1152-1159
• /
• 2015

Switching power supply systems are widely used in many industrial fields. Power factor correction (PFC) circuits have a tendency to be applied in new power supply designs. The PFC circuit with a boost converter using an input power source is studied in this paper. In a boost PFC circuit, there are two feedback control loops: a current feedback loop and a voltage feedback loop. In this paper, the regulation performance gained by using the output voltage and compensator to improve the transient response presented at the continuous conduction mode (CCM) of the boost PFC circuit is analyzed. The validity of the designed boost PFC circuit is confirmed by both MATLAB simulation and experimental results.