• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.69-78
• /
• 1995

The arbitrary Lagrangian-Eulerian(ALE) finite element analysis is applied to the axisymmetric hot extrusion through continuous dies. In order to simulate hot forming problems, an ALE scheme for temperature analysis is proposed. The computed results are compared with experimental results as with those by pure Lagrangian method. In the present study mesh control is accomplished by the use of isoparametric mapping of quadrilaterals.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.116-121
• /
• 1999

Since the material flow near the die part in CONFORM (Continuous Extrusion Forming) process is similar to that of side-extrusion, the side-extrusion model of tube shaped aluminum profiles was studied for the die design in CONFORM process. In this paper, the effects of process parameters in the side -extrusion through a two-hole die face, such as material flow, height and thickness of the tube, velocities of punch and lengths of bearing land were investigated using UBET program and DEFORM commercial FEM code. The optimum lengths of the bearing lands and punch velocities for obtaining the straight shape products required were determined.

• Restorative Dentistry and Endodontics
• /
• v.29 no.5
• /
• pp.439-445
• /
• 2004

The purpose of this study was to evaluate the influence of plugger penetration depth on the apical extrusion of root canal sealer during root canal obturation with Continuous Wave of Condensation Technique. Root canals of forty extracted human teeth were divided into four groups and were prepared up to size 40 of 0.06 taper with ProFile. After drying. canals of three groups were filled with Continuous Wave of Condensation Technique with System $B^{TM}$ and different plugger penetration depths of 3. 5, and 7 mm from the apex. Canals of one group were filled with cold lateral compaction technique as a control. Canals were filled with non-standardized master gutta-percha cones and 0.02 mL of Sealapex. Apical extruded sealer was collected in a container and weighed. Data was analyzed with one-way ANOVA and Duncan's Multiple Range Test. 3 and 5 mm penetration depth groups in Continuous Wave of Condensation Technique showed significantly more extrusion of root canal sealer than 7 mm penetration depth group (p < 0.05). However, there was no significant difference between 7 mm depth group in Continuous Wave of Condensation Technique and cold lateral compaction group (p < 0.05). The result of this study demonstrates that deeper plugger penetration depth causes more extrusion of root canal sealer in root canal obturation by Continuous Wave of Condensation Technique. Therefore, special caution is needed when plugger penetration is deeper in the canal in Continuous Wave of Condensation Technique to minimize the amount of sealer extrusion beyond apex.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.232-235
• /
• 1995

A side-extrusion model, meant for deeper understanding of the material flow in the CONFORM (continuous extrusion forming) of trub shaped aluminum profiles is presented. In order to get the desirded straight shape of the extrudate,every part of its cross-section must exit the die with the same velocity. Problem is assumed by plane strain UBET-model to analyze it in a simplified way. This has been done by studying the side-extrusion through a two -hole die face. The flow is balanced by determining the optimum lengths of the bearing lands, i.e., those lengths which result in equal exit velocities of the extrudates. Furthermore, the material flow, as influenced by the punch velocity, has been investigated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.329-332
• /
• 2006

$Conform^{TM}$, a continuous extrusion forming process can produce a variety of very long extruded products such as aluminum alloyed wires, strips and profiles, hollow sectioned tubes, coated wires used in the current forming industry. This process has some advantages like as superiority of pre-heating free, availability of high extrusion ratio and continuous forming without stroke limit. But it is still difficult to analyze the realistic model of the process. In this study the analysis using two-dimensional model of $Conform^{TM}$ process together with several parametric investigations on the heat transfer are carried out by FEA code DEFORM $^{TM}2D$. In spite of simple model the results of analysis shows a good guidance to design the real process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.139-143
• /
• 1996

The theoretical study of deformation behavior for continous extrusion process (CONFORM) is shown in this paper. The extrusion process is compared with a conventional route, side extrusion, considering extrusion ratios, flash gaps and coefficients of friction. In each case the distribution of strain and strain rate is predicted by using the finite element method. In this study simplifying assumptions on the deformation geometry are made to investigate the plastic flow occuring in the area of deformation of the Conform process.

• Journal of Powder Materials
• /
• v.15 no.3
• /
• pp.204-209
• /
• 2008

Aluminum alloys are not only lightweight materials, but also have excellent thermal conductivity, electrical conductivity and workability, hence, they are widely used in industry. It is important to control and enhance the densification behavior of metal powders of aluminum. Investigation on the extrusion processing combined with equal channel angular pressing for densification of aluminum powders was performed in order to develop a continuous production process. The continuous processing achieved high effective strain and full relative density at $200^{\circ}C$. Optimum processing conditions were suggested for good mechanical properties. The results of this simulation helped to understand the distribution of relative density and effective strain.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.39-45
• /
• 2011

In this study, the heat flow of the plant scale aluminum extrusion process was investigated to establish optimum continuous heat treatment conditions. During the extrusion of 6061 aluminum alloy, processing parameters such as the extrusion pressure, speed and temperature histories of billets were logged as a function of time. The surface temperature of the billets increased at constant ram speed, while it decreased with decreases of the ram speed. In order to maintain the billet temperature within a solutionizing temperature range prior to the succeeding water quenching step, the ram speed or the temperature of the blower should be controlled. The temperature histories of the billets during the extrusion and hot air blowing processes were successfully simulated by using the velocity boundary model in ANSYS CFX. The methodology to design an optimum process by using a commercial simulation program is described in this study on the basis of the metallurgical validation results of the microstructural observation of the extrudates. The developed model allowed the advantages of taking into account the motion of the extrudate coupled with the temperature change based on empirical data. Calculations were made for the extrudate passing through the isothermal chamber maintained at appropriate temperature. It was confirmed that the continuous heat treatment system is beneficial to the productivity enhancement of the commercial aluminum extrusion industry.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.105-109
• /
• 1996

The calculation of the total power required at the Continuous Extrusion Forming(CONFORM) has been performed by the theoretical analysis of three transformation regions(primary grip length and extrusion grip length, flashing). In this study, that was performed by five transformation regions(biting, upsetting, filling, extruding, flashing)and four transformation regions(biting, upsetting and filling, extruding, flashing) and then results of theoretical analyses were compared with experimental results. Results of analysis by four and five transformation regions than that of three transformation regions in the CONFORM showed in a good agreement with experimental results.

• Transactions of Materials Processing
• /
• v.23 no.3
• /
• pp.178-183
• /
• 2014

Continuous casting is a process where molten metal is solidified into a semi-finished billet on a large scale with either a rectangular or round cross section for subsequent processing. The use of continuous casting provides an opportunity for producing material on a practical industrial scale with lower cost than conventional casting. In the current study, the material was fabricated by continuous casting and subsequent extrusion. Tensile tests were conducted on continuous cast ZK60A after extrusion over a range of strain rates at temperatures from 473K to 623K. The alloy exhibits a quasi-superplastic behavior with a maximum recorded elongation of ~250% at 523K when tested with an initial strain rate of $10^{-5}/s$. The experiments give a strain rate sensitivity exponent of 0.3~0.4 and an activation energy of 108 kJ/mol. From the current investigation, it was found that the high-temperature plastic flow of the ZK60A is controlled by a dislocation viscous glide mechanism.