• Journal of the Korea Concrete Institute
• /
• v.11 no.4
• /
• pp.137-145
• /
• 1999

The use of steel fiber reinforced to improve the strength and flexural toughness of concrete is well known, but reinforcement of polymer concrete with steel fibers has been hardly reported till now. Polymer concrete has high strength, durability and freeze-thaw resistance than that of cement concrete, but it has disadvantage such as low flexural toughness. In this paper, the strength characteristics and flexural toughness of steel fiber reinforced polymer concrete are investigated experimentally with various steel fiber aspect ratios($\ell$/d), and contents(vol.%). As the result, the flexural and splitting tensile strengths and flexural toughness were increased aspect ratio, and reach the maximums at a aspect ratio of 50. The relationship between the compressive, flexural and splitting tensile strength were high. And the relationship between flexural strength and strain energy was approximately linear.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.150-151
• /
• 2014

Although there has been many research regarding improving anti-shock performance and durability of concrete using fiber-reinforcement, there are still drawback on workability with interruption of fibers such as fiber-ball. Hence to solve this problem, in previous research, the optimum combination of fibers to improve workability of HPFRCC. In this research, based on the result of previous research, to improve the workability further, various fine aggregate contents is evaluated on workability, and the most appropriate mixing proportion is suggested.

• Computers and Concrete
• /
• v.11 no.6
• /
• pp.531-539
• /
• 2013

An experimental investigation of mechanical properties of jute fiber-reinforced concrete (JFRC) has been reported for making a suitable construction material in terms of fiber reinforcement. Two jute fiber reinforced concretes, called jute fiber reinforced normal strength concrete (JFRNSC) and jute fiber-reinforced high-fluidity concrete (JFRHFC), were tested in compression, flexure and splitting tension. Compressive, flexural and splitting tensile strengths of specimens were investigated to four levels of jute fiber contents by volume fraction. From the test results, Jute fiber can be successfully used for normal strength concrete (NSC) and high-fluidity concrete (HFC). Particularly, HFC with jute fibers shows relatively higher improvement of strength property than that of normal strength concrete.

• Journal of Families and Better Life
• /
• v.22 no.1
• /
• pp.153-167
• /
• 2004

The purpose of this study was to investigate the difficulties, conflicts, and communications between female-headed single parents and their children, their child rearing methods and attitude, and the political suggestions for the welfare in those families. The in-depth interviews were conducted for 7 women in Gyonggi-Do and Chungnam-Do on March 3-27, 2003. The interviewees were selected for the mothers whose children were enrolled either elementary schools or middle schools. The contents of interviews were receded to be analyzed by qualitative method. The results were as follows; first, female-headed single parent families were in low economic status with unstable employment condition. Secondly, women in that families were confronted with psychological problems because of their multiple roles and low income. Third, although they had a controlled child rearing method, they used much reinforcement and praise. Thirdly, they were in need of the aids for the basic life such as housings and their children's private institute expenses. Finally, they required the repealing of an existing birthright system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.1
• /
• pp.47-58
• /
• 2004

Loss factors of A356, Mn-Cu alloy and aluminum matrix composites reinforced with $SiC_p$ and Ni-coated graphite particles at various contents have been investigated using clamped-free cantilever beam method. The loss factors of half-power bandwidth of the specimens were measured over a wide range of frequencies from 50 to 3300Hz. Among the specimens, Al-10%$SiC_p$-10%$C_p$ showed the highest loss factor at the mode I, while Mn-Cu alloy showed the highest loss factors at the modes II and III. Consequently, at the mode I the Al-10%$SiC_p$--10%$C_p$ showed the loss factor of 0.00093, which is 2.64 and 1.58 times higher than those of A356 and Mn-Cu alloy, respectively.

• Polymer(Korea)
• /
• v.24 no.4
• /
• pp.564-570
• /
• 2000

The waste FRP occured in the fabrication of SMC (sheet molding compound) bathtubs and the waste polyurethane foam occured in electronic manufacture and waste insulator were applied as a soundproof and light weight pannel in the waste FRP unsaturated polyester matrix resin composites to recycle. The effect of filler contents on the mechanical properties and interfacial phenomena of the filler and matrix on the composites was evaluated. The tensile strength of composites reached its maximum value of 82.34 MPa when the filler content was 70 wt%, and the more content of reinforcement is increased, the more tensile modulus was decreased. The flexural strength and modulus of composites, reinforced 70 wt% with filler content, were dominant compared to the other samples to 72.5 MPa, 958.4 MPa respectively. When composite of reinforced 70 wt% with filler content, it was confirmed that pull out phenomena and cracks did not occur in the interface of reinforcement and matrix resin through the SEM observation. Also, waste FRP and urethane foam were dispersed well into matrix resin as filler.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.40-45
• /
• 2003

In this work, the effect of different contents of $Fe_3O_4$ and temperature variation on the electrical conductivity ($\sigma$) in the polar acrylonitrile butadiene rubber (NBR)/$Fe_3O_4$ (magnetite) mixture system was investigated. It was found that the percolation threshold concept holds true for the conductive particle-filled composites where $\sigma$ indicates a nearly sharp increase when the concentration of magnetite in the mixture exceeds 22%. The temperature dependence of $\sigma$ was thermally activated below and at the percolation threshold ($P_c$). Magnetite acted as reinforcing and conductive filler for NBR. At room temperature and higher voltages, the electrical current was proportional to the square of voltage ($I{\propto}V^2$) for the composites which contain 30 phr of magnetite. Moreover, it was shown that the composites with magnetite of 50 phr showed the highest tensile strength and elongation at break, which was due to the formation of optimal physical interlock and crosslinking. The results of 100%, 200%, and 300% Young moduli said that the moduli are largely correlated with reinforcement effect of magnetite and viscosity of the blends from torque curve.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.283-293
• /
• 2015

In order to evaluate corrosion resistance of steel fiber-reinforced concrete, accelerated chloride migration and surface resistivity tests were conducted. In addition air content of fresh concrete, compressive strength and water absorption were measured for investigating fundamental characteristics of concrete. Two different water-cement ratios(0.44, 0.5) and three steel fiber contents(0.25%, 0.5%, 1%) were considered as variables. Note that all specimens cast with same compaction work. As a results, corrosion resistance decreased as steel fiber contents increased regardless of water-cement ratio when the concrete was compacted with same amount of work done. However, for concrete with same steel fiber content, the lower water-cement ratio showed the better corrosion resistance. It is found that enhancement of fluidity and enough compaction should be done for corrosion resistance of SFRC.

• The Journal of the Korea Contents Association
• /
• v.20 no.7
• /
• pp.185-194
• /
• 2020

This study aims to figure out how the brand experience design elements works in the Shortform video-based branding through case analysis. The sense, feel, think, act, relate experience of Shortform video brand are provided through the implementation of specific experience design elements in the process of the creators expressing personality through social media channels and communicating and interacting with consumers. As a result, LIZIQI's food videos provided a brand identity as an 'Eastern gourmet' to consumers through the audiovisual stimulation of food in video, the cognitive reinforcement which is combined of identities and products, and the behavioral participation by web sites·electronic media. In addition, a strong brand relationship was established by sharing emotional ties using human factors and responsibility through co-branding. This can be extended to various Shortform video contents-based branding cases, and it will suggest a useful approach to the brand building strategy through strategic brand experience design elements.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.238-245
• /
• 2012

Graphene oxide was synthesized from natural graphite, and its surface was modified using diisocyanatodicyclohexylmethane( $H_{12}MDI$). Isocyanate-graphene sheet(i-RGO) was obtained by reduction of surface modified GO. To select nanofiller having good dispersion with polyurethane, GO, i-RGO, natural graphite and thermal reduced graphite were analyzed, and then i-RGO was selected as a suitable nanofiller. PU/i-RGO nanocomposite was synthesized with various i-RGO contents to estimate effect of reinforcement on nanocomposite. Thermal stability, hardness, contact angle were increased with i-RGO contents due to i-RGO characteristic and crosslink bridge effect. But, tensile strength and elongation were decreased at i-RGO contents more than the 4 wt%. This phenomenon was interpreted by the excess formation of crosslink bridge.