• Journal of the Korean institute of surface engineering
• /
• v.52 no.4
• /
• pp.194-202
• /
• 2019

A systematic investigation was made on the influence of processing parameters such as gas composition and treatment temperature on the surface characteristics of hardened layers of low temperature plasma nitrided 316L Austenitic Stainless Steel. Various nitriding processes were conducted by changing temperature ($370^{\circ}C$ to $430^{\circ}C$) and changing $N_2$ percentage (10% to 25%) for 15 hours in the glow discharge environment of a gas mixture of $N_2$ and $H_2$ in a plasma nitriding system. In this process a constant pressure of 4 Torr was maintained. Increasing nitriding temperature from $370^{\circ}C$ to $430^{\circ}C$, increases the thickness of S phase layer and the surface hardness, and also makes an improvement in corrosion resistance, irrespective of nitrogen percent. On the other hand, increasing nitrogen percent from 10% to 25% at $430^{\circ}C$ decreases corrosion resistance although it increases the surface hardness and the thickness of S phase layer. Therefore, optimized condition was selected as nitriding temperature of $430^{\circ}C$ with 10% nitrogen, as at this condition, the treated sample showed better corrosion resistance. Moreover to further increase the thickness of S phase layer and surface hardness without compromising the corrosion behavior, further research was conducted by fixing the $N_2$ content at 10% with introducing various amount of $CH_4$ content from 0% to 5% in the nitriding atmosphere. The best treatment condition was determined as 10% $N_2$ and 5% $CH_4$ content at $430^{\circ}C$, where the thickness of S phase layer of about $17{\mu}m$ and a surface hardness of $980HV_{0.1}$ were obtained (before treatment $250HV_{0.1}$ hardness). This specimen also showed much higher pitting potential, i.e. better corrosion resistance, than specimens treated at different process conditions and the untreated one.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.43-44
• /
• 2012

Deterioration factors such as CO₂ and chloride ions cause steel corrosion in RC structures. The diffusion of these factors depends on the water content in concrete. To examine the moisture condition of concrete, this research considers the availability of the steel effect ratio, which is calculated by Resistivity Estimation Model (REM). It is concluded that the steel effect ratio is expected to be available as a quantitative evaluation method in the assessment of concrete layer resistivity.

• Journal of Life Science
• /
• v.5 no.4
• /
• pp.155-161
• /
• 1995

The effects of substrate concentration, enzyme concentration, reaction temperature, and water content were investigated in intramolecular esterification. This study used cyclohexane as organic solvent, power lipase as enzyme, and benzyl alcohol and octanoic acid as substrate. The initial reaction rate was found to be proportional to enzyme concentration; followed Michaelis-Menten equation for octanoic acid; and was inhibited by benzyl alcohol . The observed initial reaction rate first increased, then decreased with increasing reaction temperature, giving rise to the maximum rate at 20$\circ$. The drop in the reaction rate at higher temperature was to partition equilibrium change of substrate between organic solvent and hydration layer of enzyme molecule in addition to the deactivation by enzyme denaturation. Water layer surrounding enzyme molecule seemed to activate in organic solvent and the realistic reaction was done in the water layer. In the enzymatic reaction in organic solvent, the initial reaction rate was influenced by partition quilibrium of substrate, so the optimum condition of substrate concentration, enzyme concentration, reaction temperature, and water content would give a good design tool.

• 연구논문집
• /
• s.29
• /
• pp.163-171
• /
• 1999

A new titanium alloy system. Ti-xFe-ySi (x,y=0-4 wt%). was designed and characterized with the point at low cost and high strength for casting applications. Fe improved room and elevated temperature mechanical properties owing to solid solution hardening and beta phase stabilization. Si yielded titanium silicides and Si addition over 1 wt% resulted in poor ductility due to coarse silicide chains at prior beta boundaries. The optimum composition was found to be Ti-4Fe-(0.5-1)Si in the viewpoint of tensile strength and ductility which are comparable to the Ti-6Al-4V. The metal-mould reaction was also examined for Ti-xFe and Ti-xSi binary alloy system. The thickness of surface reaction layer w as not affected significantly with Fe content, while it was decreased with Si content. In the Ti-4Si alloy, no reaction layer was found. The depth of surface hardening layer was about $200\mum$ regardless of the mould materials.

• Structural Engineering and Mechanics
• /
• v.65 no.3
• /
• pp.275-290
• /
• 2018

The hygrothermal stresses in sandwich plate with composite faces due to through the thickness gradient temperature and (or) moisture content are investigated. The layer-wise theory is employed for formulation of the problem. The formulation is derived for sandwich plate with general layer stacking, subjected to uniform and non-uniform temperature and moisture content through the thickness of the plate. The governing equations are solved for free edge conditions and 3D stresses are investigated. The out of plane stresses are obtained by equilibrium equations of elasticity and by the constitutive law and the results for especial case are compared with the predictions of a 3D finite element solution in order to study the accuracy of results. The three-dimensional stresses especially the free edge effect on the distribution of the stresses is studied in various sandwich plates and the effect of uniform and non-uniform thermal and hygroscopic loading is investigated.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.644-647
• /
• 1996

The distribution of coercivity in the thickness direction were investigated by using Kerr hysteresis loop tracer for the Co-Cr films deposited by Facing Targets Sputtering apparatus. It was found that the difference between the coercivities of surface layer and initial growth layer H$_c$$\bot$(S)-H$_c$$\bot$(I) correlated strongly with $\Delta$H$_o$, shich represents the degree of distribution of coercivity. Furthermore, the Cr content was varied in order to improve the coercivity of imitial growth layer H$_c$$\bot$(I) and distribution of coercivity. H$_c$$\bot$(I) took a maximum value of 750 Oe and the distribution of coercivity became sharper at the Cr content of 25at. %.

• Journal of the Mineralogical Society of Korea
• /
• v.11 no.2
• /
• pp.97-105
• /
• 1998

Weathering of biotite in Palgonsan granite was studied by using X-ray diffraction, optical microscopy, scanning electron microscopy, and electron probe micro analysis. Biotite altered to biotite/vermiculite regular mixed layer mineral (B/V) in the early stage of weathering. Although partially replaced by kaolinite with the progress of weathering. B/V is the major weathering product of biotite throughout the profile. During the formation of B/V, Mg, Fe and K are removed from a biotite layer to form a vermiculite layer by about 28%, 44% and 88%, respectively, whereas the Ti content is not changed. Considerable volume increase after the kaolinitization of B/V suggests that Al and Si are largely introduced from the external weathering solution. The silicate lattice templet of a weathering biotite facilitated the nucleation and growth of kaolinite. In the Palgongsan granite weathering profile, plagioclase weathered mostly into halloysite whereas biotite greatly contributes to the kaolinite crystallization though its small content in fresh rock.

• Journal of the Korean institute of surface engineering
• /
• v.4 no.1
• /
• pp.16-23
• /
• 1971

In this study , fluoborte solution consisting of lead fluoborate, tin fluoborate and cupric acetate was used. By addition of small amount of Cu+= ion to the solution, the Cu content of deposition layer was almost controlled less than 5%. The amount of Cu in deposition layer was almost constant without any influence of Pb++ & Sn++ in the solution, and the amount of Pb was increased by the increase of total concentration of Pb++ +Sn++ in the solution, and the amount of Pb was increased by the increase of total concentration of Pb++ +Sn++ in the solution . Agitation of plating solution & low current density result in the increase of Cu content. Analyzing of microscopic structures and etching tests of the deposited alloy, it was believed that the alloy had a lamellar structure consisting of copper rich lamellar and lead rich layer.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.525-529
• /
• 2017

To improve the thermal resistance of a porous borosilicate lining block, we prepared and applied polysiloxane-fumed silica-ethanol slurry on top of the block and fired the coating layer using a torch for 5 minutes at $800^{\circ}C$. We conducted magnified characterizations using a microscope and XRD analysis to observe phase transformations, and TGA-DTA analysis to determine the thermal resistance. Thermal characterizations showed improved heat resistance with relatively high polysiloxane content slurry. Cross-sectional optical microscope observation showed less melting near the surface and decreased pore formation area with higher polysiloxane content slurry. XRD analysis revealed that the block and coating layer were amorphous phases. TGA-DTA analysis showed an endothermic reaction at around $550^{\circ}C$ as the polysiloxane in the coating layer reacted to form SiOC. Therefore, coating polysiloxane on a borosilicate block contributes to preventing the melting of the block at temperatures above $800^{\circ}C$.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.5
• /
• pp.303-311
• /
• 1994

In this study, the factors, such as coating temperature T(K), reaction time t(sec) and mobile carbon content $C^*$ (wt%) of steels affecting, the growth rate of carbide layer were investigated in the reactive deposition and diffusion coating using the fluidized bed. From the results, the coating thickness d(cm) can be expressed by an equation. d=$C^*$$(KT)^{1/2}$, where K=K$\circ$exp(~Q/RT), KTEX>$\circ$ = 1.4$\times$$10^{-2}cm^{-2}$/sec, and Q=46Kcal/ mol. It was in a good aggrement with the experimental results, reguardless of the diffusion coating method and the carbide layer. Therefore, if the mobile carbon content of carbon steels and alloyed steels is known, the thickness under coating conditions can be predicted from the previous equation.