• Geomechanics and Engineering
• /
• 제28권2호
• /
• pp.107-116
• /
• 2022

The steady state of unsaturated soil takes a long time to achieve. The soil seepage behaviours and hydraulic properties depend highly on the wetting/drying rate. It is observed that the soil-water characteristic curve (SWCC) is dependent on the wetting/drying rate, which is known as the dynamic effect. The dynamic effect apparently influences the scanning curves and will substantially affect the seepage behavior. However, the previous models commonly ignore the dynamic effect and cannot quantitatively describe the hysteresis scanning loops under dynamic conditions. In this study, a dynamic hysteresis model for SWCC is proposed considering the dynamic change of contact angle and the moving of the contact line. The drying contact angle under dynamic condition is smaller than that under static condition, while the wetting contact angle under dynamic condition is larger than that under static condition. The dynamic contact angle is expressed as a function of the saturation rate according to the Laplace equation. The model is given by a differential equation, in which the slope of the scanning curve is related to the slope of the boundary curve by means of contact angle. Empirical models can simulate the boundary curves. Given the two boundary curves, the scanning curve can be well predicted. In this model, only two parameters are introduced to describe the dynamic effect. They can be easily obtained from the experiment, which facilitates the calibration of the model. The proposed model is verified by the experimental data recorded in the literature and is proved to be more convenient and effective.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.613-619
• /
• 2000

This paper presents a mettled to reduce the number of conductors of catenary system for estimating line constants. Conductors of a catenary system are grouped and reduced. For example, the model representing the contact and the messenger conductors with a single equivalent conductor is. probably more realistic than assuming the two conductors completely separated, since they are generally connected by droppers every few meters. Therefore, this paper shows the method to reduce the number of conductors using electric circuit theory. To verify the results, we compared the equivalent line constants obtained by proposed method with those obtained by measurement.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.135-142
• /
• 2000

This Paper describes a characteristics of wheel wear of high speed train running on the conventional line. Conventional line has many curved tracks that cause severe wheel flange wear. The influences of lubrication, cant deficiency, owe radius on wheel wear are also described considering the operation performance of the highspeed trainset. A method of calculation using contact patch work model is presented far determination of the evolution by wear of railway wheels.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.117-119
• /
• 2002

In this paper, the geometry effectiveness and contact modes as functions of real contact length on a cap ring have been analyzed for high pressure sealing mechanism in reciprocating actuator. The reaction force and elastic strain energy density are very important parameters for analyzing the sealing performance of an ACGT ring seal. For the high pressure of 800bar and the maximum speed of 3m/s, the main piston is reciprocating along the linear line against the cylinder wall. The computed results indicate that the length ratio of a cap ring is more influential design parameter compared to that of the tribological contact mode. Thus, this paper recommends the discrete contact area rather than a conventional flat contact model. Especially, the sealing capacity is more improved when the length ratio of a cap ring is below 0.625.

• 터널과지하공간
• /
• 제15권4호
• /
• pp.305-315
• /
• 2005

불연속 변형해석은 에너지 최소화원리를 이용하여 전체 행렬을 구성하는 유한요소법과 개별블록의 대변위를 모사할 수 있는 개별요소법의 장점을 모두 가지고 있는 해석법이다. 이 연구에서는 불연속 변형해석에서 해석결과에 문제점이 있는 접촉문제를 개선하는 시도로써 불연속 변형해석에서 정의하는 접촉 중 선-선 접촉을 해석하는 새로운 기법을 적용하였다. 이를 위해 접촉쌍의 개념을 이용하여 새로운 7 가지의 선-선 접촉의 상태를 정의하고 이에 따른 새로운 전단거동 결정 방법과 개폐수렴반복해석에서의 수렴조건, 접촉찾기 등의 세부알고리듬을 제시하였다. 또한 블록간의 접촉에 의해 작용하는 마찰력을 기존의 점하중 형태에서 선하중의 형태로 개선하는 식을 유도하여 새 알고리듬에 적용하였다.

• 한국생산제조학회지
• /
• 제23권5호
• /
• pp.435-442
• /
• 2014

This paper describes an improved design model that can be used to configure a non-contact pneumatic device to turn a large sheet at the in-line system. For rotational moving in the conveyor system, the conventional method is to turn the system itself. The improved non-contact pick-up system mainly uses 8 pairs of L-shaped latches and 12 swirl type heads. It is positioned above the upward air flow table. This system performs the non-contact gripping and side-edge contact support in the vertical and rotational directions to hold the self-weight of a large flat sheet. A non-contact air head can exert a sufficient gripping ability at 4N lower than the standard working pressure. The side latches support 60% of the lifting force required. Through structural and flow analysis, the working conditions were simultaneously considered in accordance with the deflection and flatness of the glass.

• Nuclear Engineering and Technology
• /
• 제50권8호
• /
• pp.1330-1338
• /
• 2018

High-density UMo/Zr monolithic nuclear fuel plates have a promising application prospect in high flux research and test reactors. The solid state welding method called co-rolling is used for their fabrication. Hot co-rolling simulations for the composite blanks of UMo/Zr monolithic nuclear fuel plates are performed. The effects of coupon sizes and mechanical property parameters on the contact pressures between the to-be-bonded surfaces are investigated and analyzed. The numerical simulation results indicate that 1) the maximum contact pressures between the fuel coupon and the Zircaloy cover exist near the central line along the plate length direction; as a whole the contact pressures decrease toward the edges in the plate width direction; and lower contact pressures appear at a large zone near the coupon corner, where de-bonding is easy to take place in the in-pile irradiation environments; 2) the maximum contact pressures between the fuel coupon and the Zircaloy parts increase with the initial coupon thickness; after reaching a certain thickness value, the contact pressures hardly change, which was mainly induced by the complex deformation mechanism and special mechanical constitutive relation of fuel coupon; 3) softer fuel coupon will result in lower contact pressures and form interfaces being more out-of-flatness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.265.1-265.1
• /
• 2016

여러 application에 적용하기 위하여 p-type SnO 박막과 전극 간의 접촉 저항을 분석이 필요하였다. 이를 Transmission Line Method(TLM) 패턴 소자를 제작한 후 전기적 특성을 분석함으로써 알 수 있었다. $Si/SiO_2$ 기판에 Reactive Magnetron Sputtering법을 이용하여 c축 우선 배향된 SnO를 100nm 증착하고 photolithography 공정을 통해 전극을 패턴화하여 100nm 두께로 증착하였다. 전극 간 거리는 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, $1024{\mu}m$로 각각 2배씩 증가하는 패턴이고 폭 W는 $300{\mu}m$ 이다. p-type SnO 의 경우, work function이 4.8eV이기 때문에 전극과 ohmic contact이 되기 위해서는 4.8eV보다 높은 work function 값을 가지는 전극이 필요하였다. 이 조건과 맞는 후보로 Ni(5.15eV), ITO(5.3eV)를 설정한 후 소자를 제작하였다. 제작된 소자는 열처리 하지 않은 소자와 Rapid Thermal Annealing(RTA) 장비에서 $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$에서 각각 1분씩 열처리한 소자의 특성을 분석하였다. 열처리 하지 않은 소자의 경우 Ni 전극의 specific contact resistance는 $3.42E-2{\Omega}$의 값을 나타내었고, ITO의 경우 $3.62E-2{\Omega}$값을 나타내었다.

• 한국소음진동공학회논문집
• /
• 제19권1호
• /
• pp.85-93
• /
• 2009

There are many curves in Seoul subway system. Therefore, the noise from subway system in curved line gives displeasure to passenger. The subway noise in curved line is affected not only by rail condition but also wheel condition and dynamic characteristics. The railway curving noise can be divided into 2 categories. The first is the noise due to stick-slip between wheel tread and rail head, and the second is one by wheel flange contact on rail side. Because of these phenomena - stick-slip and wheel flange contact - wheels are worn seriously. In this study the curving noise was reviewed by using eigen-mode of wheel and waterfall plot which shows noise level in time-frequency domain. And also those were reviewed in viewpoint of stick-slip noise and wheel flange contact noise. Finally, the relationship between curving noise and wheel wear was studied.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.546-549
• /
• 2009

In this paper, we investigated the effects of different source/drain (S/D) electrode materials in thin film transistors (TFTs) based on indium-gallium-zinc oxide (IGZO) semiconductor. A transfer length and effective resistances between S/D electrodes and amorphous IGZO thin-film transistors were examined. Intrinsic TFT parameters were extracted by the transmission line method (TLM) using a series of TFTs with different channel lengths measured at a low drain voltage. The TFTs fabricated with Cu S/D electrodes showed the lowest contact resistance and transfer length indicating good ohmic characteristics, and good transfer characteristics with a field-effect mobility (${\mu}_{FE}$) of 10.0 $cm^2$/Vs.