• 한국안전학회지
• /
• 제27권3호
• /
• pp.36-41
• /
• 2012

Electrical Connections often cause fires due to poor contact. Occurrence rate of these fires tends to increase annually. The reason why poor contacts occur is often because it is the low mechanical pressure at the contact points. A typical connection method using mechanical pressure is a screw terminal type. This study reviewed these poor contact cases in the screw terminals. In order to get reproduction of such cases, two types of experiments were conducted. the first one was conducted under the normal contact condition, and the other one was conducted under the poor contact condition that screw terminal of breaker was loosen and did not meet the requirements of toque value. In both types of experiments, compulsory vibration was adopted as a variable to aggravate poor contacts. Each of various current values(4.5A, 9.0A, 13.5A) is input. In these experiments, relationships of a contact, electrical signal such as current and electric pulse by ZCT and thermal characteristics according to vibration effect are analyzed. The suggested data and results in this study provide the useful resources helping to investigate fires due to poor contact, and they develop the detector for poor contact and finally reduce the electrical fire occurrence rate.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1559-1566
• /
• 1994

Using the finite element method, the contact force, contact band width and temperature distribution of lip seals analyzed for the interference including some nonlinearities such as material nonlinearity, geometrical nonlinearity and nonlinear contact boundary condition. The calculated results showed that the contact stress concentrated on the contact zone between the garter spring and the rubber toward the flex side, the contact edge of lip seals. The high contact forces due to the increased interference separate the sealing gap between the lip edge and the rotating shaft. This may lead to leak the sealed oil.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.491-494
• /
• 2002

To assess the electrostatic interaction of surfaces at the triple contact line, the electrostatic field is analyzed by using the finite element method. The Helmholtz free energy is used as a functional which should be minimized under an equilibrium condition. The numerical results are compared with the nonlinear analytical solution for a two-dimensional charged interface and linear solution for a wedge shaped geometry, which shows fairly good agreement. The method is applied to the analysis of electrostatic influence on the contact angle on a charged substrate. The excess free energy found to increase drastically as the contact angle approaches to zero. This excess free energy Plays an opposite role to the Primary electrocapillary effect, as the contact angle gets smaller. This enables an alternative explanation for the contact-angle saturation phenomenon occurring in electrical control of surface tension and contact angle.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.160-165
• /
• 2002

The flying height of contact slider is determined by vertical and pitching motions. This paper performed the computer simulation for flying height change of contact slider. It is changed by many parameters, contact stiffness. contact damping, all bearing stiffness ratio and so on. So computer simulation analysis is performed for knowing for what change of these parameters influences in flying height of contact slider. The practical recording zone surface is gotten by using SPM. In recording zone, flying height is simulated for each parameter. the settling time which the flying height of contact slider is lower than 10nm is analyzed over practical disk surface for changing each parameter. Through these results, the contact slider can be analyzed for more accuracy dynamic characteristics.

• Tribology and Lubricants
• /
• 제31권5호
• /
• pp.189-194
• /
• 2015

This paper focuses on the conformal contact problem. A typical example of conformal contact is the contact between a pin and hole. In particular, this paper focuses on the condition for assuming a contact stress field to be a Hertzian pressure profile by using well-known classical solutions associated with Hertzian contact. Persson first developed the conformal contact analysis method around half a century ago, but there have been no significant improvements since then. The present research also adopted this method, but developed new solutions from the viewpoint of application to structural design. The analysis began with a comparison between Persson°Øs conformal contact stress and the Hertzian stress fields. The next step was to check the differences in the normalized stress values of both. This study used the tolerance for the difference in the peak stresses of Persson°Øs solution and the Hertz solution to validate the Hertzian assumption. This gave the range for the difference in radii of the pin and hole when the contact force and mechanical properties of the material are specified. The results showed that, at a tolerance of 5%, the Hertzian assumption is valid if half of the contact angle is less than 35°ý. In addition, the Hertzian assumption holds even for a relatively long contact length, in contrast to the general incomplete contact problem. This paper discusses these results along with other aspects of the application to the design.

• 대한수학회보
• /
• 제47권3호
• /
• pp.541-549
• /
• 2010

In this paper we derive an integral formula on an (n + 1)-dimensional, compact, minimal contact CR-submanifold M of (n - 1) contact CR-dimension immersed in a unit (2m+1)-sphere $S^{2m+1}$. Using this integral formula, we give a sufficient condition concerning with the scalar curvature of M in order that such a submanifold M is to be a generalized Clifford torus.

• Kyungpook Mathematical Journal
• /
• 제51권4호
• /
• pp.457-468
• /
• 2011

We consider pseudo-symmetric and Ricci generalized pseudo-symmetric N(${\kappa}$) contact metric manifolds. We also consider N(${\kappa}$)-contact metric manifolds satisfying the condition $S{\cdot}R$ = 0 where R and S denote the curvature tensor and the Ricci tensor respectively. Finally we give some examples.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.345-352
• /
• 2013

본 논문에서는 광탄성 실험 하이브리드 법을 이용하여 접촉응력문제를 해석하는 경우의 응력형상 함수에 대해서 다루고 있다. 일반적으로 접촉응력문제는 반평면 문제로써 해석 되어지므로, 접촉응력의 경우 Airy 응력함수를 구성하는 두 해석적인 응력함수의 관계는 균열문제에서와 유사하였다. 그러나 이 관계를 그대로 접촉응력문제 (특히 특이점을 가진 경우)에 사용할 수가 없다. 그러므로 정확한 접촉문제의 해석을 위해 이들 두 해석적인 응력함수의 형태에 접촉하는 두 끝점의 조건에 따른 응력형상함수를 반드시 고려하여야만 할 것이다. 두 접촉끝점의 응력 특이성에 따라 4종류로 분류되는 이들 응력형상함수 중에서 오링 해석을 위한 중요한 두 종류의 응력형상함수를 선택하였으며, 이것의 유효성을 검증하였다.

• 대한기계학회논문집A
• /
• 제23권6호
• /
• pp.895-902
• /
• 1999

This paper deals with a numerical study of the tribological contact stress distributions of elastomeric lip seals for oscillating shafts when the sealing interference and band width between the lip ease or contact seals and the shaft are present. Using the finite element method the contact stress and band width of scraper seals are analyzed for the sealing interference including some nonlinearities such as geometrical nonlinearity, material nonlinearity and nonlinear contact boundary condition. The FEM results showed that the contact stress concentrated on the contacting lip zone between the contacting edge of lip and the shaft for the increased interference. In double lip scraper seals, ole maximum contact stress of the dust lip, which is used to exclude foreign contaminants is six times higher than that of the primary sealing lip, which is used to contain lubricants.

• Tribology and Lubricants
• /
• 제21권6호
• /
• pp.272-277
• /
• 2005

Continuously variable transmission (CVT) of toroidal type has a elliptical shape of contact zone under the elastohydrodynamic lubrication (EHL) condition, where the power is transmitted only by shearing the lubricant. Due to the small contact area of elliptical shape, the traction of the shear behaviors of lubricant over the contact zone is under extremely high contact pressure over 1.0GPa. During the power transmission by shearing the fluid, many kinds of mechanical movements occur such as squeezing, sliding, rolling and spin. Among the movements, the spin effect that is the most undesirable contact behavior in transmitting the power frequently makes significant abnormal wear damage. In this work, the analysis of elliptical contact of EHL with spin effect is performed, which will give very useful information to understand the traction behaviors in toroidal type of CVT system.