• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.34-40
• /
• 2004

This paper presents studies on curvature radius measurement using the laser interferometer. It is a general practice to measure to $10^{-10}$m in length with the recent improvement and innovations in measurement technology and the processor used. The measurement methods can generally be categorized as these two: the contactual method and non-contactual method; and in this study, we will find ways to lower the cost for a CMM, or a coordinate measurement machine, and try to find an alternative. Furthermore, we will discuss some of the ways to improve the non-contactual measurement methods-optical interferometer method and the optical triangulation method. We will measure an object using a laser distance measuring device and Set the Point-contact result with the ball-bearing type and line-contact result with the bearing type, to decide on which probe type will be used.

• 대한기계학회논문집B
• /
• 제28권9호
• /
• pp.1093-1100
• /
• 2004

Numerical analysis of the heat transfer associated with droplet impact on a hot solid surface is performed by solving the equations governing conservation of mass, momentum and energy in the liquid and gas phases. The deformed droplet shape is tracked by a level set method which is modified to achieve volume conservation and to include the effect of contact angle at the wall. The numerical method is validated through the calculations for the cases reported in the literature. Based on the numerical results, the heat transfer rate is found to depend strongly on the droplet spread radius. Decreased advancing/receding contact angles enlarge the splat radius and in turn enhance the wall heat flux. The effect of impact velocity on the droplet spread is reduced as the droplet size decreases. Also, droplet atomization is observed to significantly enhance the heat transfer rate and the effect is pronounced for a smaller size of droplet. An existing model equation to predict the maximum spread radius is improved for application to a micro droplet.

• 대한기계학회논문집
• /
• 제11권6호
• /
• pp.935-944
• /
• 1987

본 연구에서는 금속 표면의 정밀가공법을 연구대상으로 하여 구상흑연주철시 편을 미량의 테이퍼로 연삭가공하고 NACHI 6000ZZ 볼 베어링을 로울러로 사용하여 로 울러 다듬질을 행함으로써 로울러 지름 변화에 따른 가압력이 표면조도에 미치는 영향 을 구명하는데 목적을 두었으며 아울러 로울링(rolling)회수에 따른 펴면조도, 경도 및 직경의 변화량을 실험적으로 구명하였다.

• 한국안광학회지
• /
• 제18권3호
• /
• pp.279-289
• /
• 2013

목적: 소프트 콘택트렌즈를 일시 제거한 상태에서 굴절보정을 위한 굴절검사 시의 굴절력 변화를 평가하고자 하였다. 방법: 17세에서 39세(평균 $24{\pm}4.8$세)의 소프트 렌즈 착용자 91명(남자 15명, 여자 76명 총 182안)을 대상으로 하였다. 렌즈를 제거한 뒤 즉시, 30분, 60분, 90분 후 타각적, 자각적 굴절검사 및 각막곡률반경검사를 하였다. 렌즈의 종류, 피팅 및 착용 상태별로 측정 시간에 따른 굴절력 변화를 평가하였다. 결과: 타각적, 자각적 굴절검사 및 각막곡률반경검사에서 측정 시간대별로 유의한 변화를 보였다(p<0.0001). 굴절력은 측정 초기(렌즈 제거 후 30분 후)에서 완만한 근시화 경향을, 그리고 측정 후반(렌즈 제거 후 60분에서 90분)에서 미약한 근시화 경향을 보였다. 렌즈 종류, 피팅 상태, 착용 시간, 착용 일수 및 검사 전날의 수면 시간에 따른 유의한 차이는 없었으나, 각막곡률의 변화에서 측정 시간과 렌즈 종류(p=0.017), 피팅 상태(p=0.019) 및 수면 시간(p=0.010) 간의 상호작용 효과는 유의하였다. 결론: 소프트 콘택트렌즈의 종류, 피팅 및 착용 상태와 상관없이 렌즈 제거 후 굴절력과 각막곡률의 안정화 시점은 적어도 60분 이상으로 나타났다. 따라서 굴절보정을 위한 굴절검사 시 가능한 60분 이상 기다린 후 실시하여야 할 것이다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.495-496
• /
• 2007

• KSTLE International Journal
• /
• 제2권2호
• /
• pp.85-92
• /
• 2001

The variation of contact traction induced by different contact shapes is studied experimentally and theoretically. Considerations fer the contact shape are rounded, truncated and truncated with rounding punches. A fretting wear experiment is conducted with the contact configuration of the strip on the tube specimens. The strip specimen is pressed to form the end profile of a rounded and truncated with rounding punches shape. Wear on the tube is investigated, which is regarded as the slip region of the contact surface. Taken into consideration is the general solution of the normal traction in the case of the indentation by a punch with its end profile of the combination of parabolas. Then, partial slip solution is obtained numerically, which is compared with the wear on the tube. The radius of the rounding and the obliquity of the edge truncation affect the tractions considerably. It is found that the proper choice of the end profile can restrain the contact-induced failure such aswear.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1068-1073
• /
• 2003

Method for contact failure mitigation is studied in this paper. The focus is laid on the contact shape that eventually influences the internal stresses. Contact mechanics is consulted within the frame of plane problem. Hertzian contact, rounded punch and uniform traction profiles are considered. Frictional as well as frictionless contact is also considered. As results, the higher traction profile induced by the rounded punch reveals the greatest among the considered shapes. Therefore, it is suggested to increase the edge radius as large as possible if a contact body of punch shape needs to be designed. It is also found that uniform traction cannot always provide the solution of contact failure mitigation.

• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.272-280
• /
• 2015

Recently, Luu suggested fatigue life equation that uses every term of the Crossland equation with stress gradient effect. Luu’s model, however, has a limit of being unable to coverage small radii that are less than a specified length. Furthermore, rolling model has a very small contact area compared to the rolling element size, and fatigue failure occurs on the small radius such as surface asperity by cyclic loading. Therefore, it is necessary to modify fatigue life equation in order to enable fatigue analysis for a small radius. In this paper, the fatigue life considering a stress gradient effect in rolling contact was obtained using Luu’s modified equation. Fatigue analysis was performed to study the effect of stress gradient on the fatigue life using newly adopted equation and to compare the results with pervious models. In order to do this, a series of simulation such as surface stress analysis, subsurface stress analysis, and fatigue analysis are conducted for two rolling balls of same size that contact each other. Through such a series of processes, the fatigue life can be calculated and equation that is proposed in this paper evaluates the fatigue life in case the contact area is small.

• Tribology and Lubricants
• /
• 제39권4호
• /
• pp.154-166
• /
• 2023

This study establishes a numerical analysis model of the finite element overhung rotor supported by a DTRB and describes the stiffness properties of the DTRB. The vibration characteristics and contact pressure of the RBR system are predicted according to the DTRB support characteristics such as the initial axial compression and roller profile. The stiffness of the DTRB significantly varies depending on the initial axial compression and external load owing to the occurrence of rollers under the no-load condition and increase in the Hertz contact force. The increase in the initial axial compression increases the rigidity of the DTRB, thereby reducing the displacement of the RBR system and simultaneously increasing the natural frequency. However, above a certain initial axial compression, the effect becomes insignificant, and an excessive increase in the initial axial compression increases the contact pressure. The roller crowning radius, which gives a curvature in the longitudinal direction of the roller, decreases the displacement of the RBR system and increases the natural frequency as the value increases. However, an increase in the crowning radius increases the edge stress, causing a negative effect in terms of the contact pressure. These results show that the DTRB support characteristics required for reducing the vibration and contact pressure of the RBR system supported by the DTRB can be designed.

• Tribology and Lubricants
• /
• 제17권3호
• /
• pp.191-197
• /
• 2001

Nano adhesion and friction characteristics between SPM(scanning electron microscope) tips and flat plates of different materials were experimentally studied. Tests were performed to measure adhesion and friction in AFM(atomic force microscope) and LFM(lateral force microscope) modes in different conditions of relative humidity. Three different Si$_3$N$_4$ tips (rdaii : 15nm, 22nm and 50 nm) and three different flat plates of Si-wafer(100), W-DLC(tungsten-incorporated diamond-like carbon) and DLC were used. Results generally showed that adhesion and friction increased with the tip radius, and W-DLC and DLC surfaces were superior to Si-wafer. But the adhesion force of Si-wafer showed non linearity with the tip radius while W-DLC and DLC surfaces showed good correlation to the “JKR model”. It was found that high adhesion force between Si-wafer and a large radius of tip was caused by a capillary action due to the condensed water.