• Journal of the Korean Solar Energy Society
• /
• v.27 no.3
• /
• pp.1-6
• /
• 2007

In this study, we analyze the maximum power generation of photovoltaic(PV) module depending on constituent materials and incidence angle dependence of light. To verify characteristics of constituent materials, we made photovoltaic modules with 4 kinds of solar cells and textured glass according to fabrication method. To find the degree of the maximum power generation dependence on intensity of light, Solar Simulator is applied by changing angle of module and light intensity. Through this experiment, to obtain maximum power generation from limited PV modules, it is needed to fully understand constituent materials, fabrication method and dependence of incident light characteristics.

• Macromolecular Research
• /
• v.11 no.6
• /
• pp.437-443
• /
• 2003

A series of alternating and alternating block copolycarbonates containing the constituent groups of polysulfone was synthesized through a multi-step solution condensation method. For the regulation of block length, monodisperse oligomers were prepared by using a large excess of the bisphenols and were subsequently incorporated into the copolymer chains. Separating the unreacted bisphenols from the oligomers by dissolution/precipitation steps took advantage of solubility differences. The structures of the monomers, oligomers, and copolymers were characterized and confirmed by GPC, NMR spectroscopy, mass spectrometry, and elemental analysis. Monodispersity of the oligomers, which is critical for control over the block length in the copolymers, was confirmed by GPC and mass spectrometry. Of the two constituent groups of the polysulfone, the sulfone linkage stiffens the polycarbonate copolymer chain, while the ether linkage softens it.

• Journal of the Korean Ceramic Society
• /
• v.47 no.1
• /
• pp.86-91
• /
• 2010

Among various fuel cells, solid oxide fuel cells (SOFCs) offer the highest energy efficiency, when taking into account the thermal recycling of waste heat at high temperature. However, the highest efficiency and lowest pollution for a SOFC can be achieved through the sophisticated control of its constituent components such as electrodes, electrolytes, interconnects and sealing materials. The electrochemical conversion efficiency of a SOFC is particularly dependent upon the performance of its electrode materials. The electrode materials should meet highly stringent requirements to optimize cell performance. In particular, both mass and charge transport should easily occur simultaneously through the electrode structure. Matter transport or charge transport is critically related to the configuration and spatial disposition of the three constituent phases of a composite electrode, which are the ionic conducting phase, electronic conducting phase, and the pores. The current work places special emphasis on the quantification of this complex microstructure of composite electrodes. Digitized images are exploited in order to obtain the quantitative microstructural information, i.e., the size distributions and interconnectivities of each constituent component. This work reports regarding zirconia-based composite electrodes.

• Journal of Korea Foundry Society
• /
• v.38 no.1
• /
• pp.16-26
• /
• 2018

In this study, the effects of the pouring temperature, preheating temperature, surface condition and fraction of the wear resistant part on the production of duo-castings were investigated using a high Cr white cast iron with excellent abrasion resistance and a low Cr alloy steel with good toughness. The constituent materials of the duo-castings were designed to have high hardness, fracture toughness and abrasive wear resistance for the replacement of high Mn alloy steels with low abrasive wear resistance. In particular, the amount of abrasive wear of 17% Cr white cast iron was about 1/20 of that of high Mn alloy steel. There was an intermediate area of about 3mm due to local melting at the bonding interface of the duo-castings. These intermediate regions were different from those of the constituent materials in chemical composition and microstructure. This region led to fracture within the wear resistant part rather than at the bonding interface in the bending strength test. The bending fracture strengths were 516-824 MPa, which were equivalent to the bending proof strength of high Mn steel. The effects of various casting conditions on the duo-cast behavior were studied by simple pouring of low Cr alloy steel melt, but the results proved practically impossible to manufacture duo-castings with a sound bonding interface. However, the external heating method was suitable for the production of duo-castings with a sound bonding interface.

• Resources Recycling
• /
• v.11 no.4
• /
• pp.11-16
• /
• 2002

Analysis and separation of constituent materials of old car have been performed by using the industrial shredding line. For this aim, three old cars made by domestic automobile manufacturers, Sonata II, Sephia and Prince were chosen and delivered in pressed form without engine, tires and doors, etc. Shredding line was substantially composed of pre- and main-shredder. cyclone, magnetic separation, eddy current separation and man-power separation. From the separation of shredder products, iron scrap was observed to be the major material of old car accounting for 60.1 ％ of total weight and non-ferrous metals involving Al, Cu and Zn, etc. were about 2％. Light fluff, about 90％ of total fluff product, was comprised with plastic, fiber and sponge, etc. and the fraction of 5 cm undersize in light fluff was 70.5%. In case of heavy fluff, however. rubber and plastic were found to be the major constituent materials of it. Among the constituent materials of fluff, plastic showed the highest calorific value, more than 10,000 cal/gr and leather and rubber showed relatively high chlorine content, 10.3 and 2.55 wt%, respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.1-8
• /
• 2013

Constitutive modeling of constituent materials is very important for reinforced concrete (RC) frames. Cyclic constitutive behavior of unconfined concrete, confined concrete and reinforcing steel should be well defined in fiber-based discretization of RC sections. This study performs nonlinear dynamic analyses of RC frame structures to investigate the sensitivity of seismic behavior of such frames to different constitutive models of constituent materials. The study specifically attempts to examine confinement effects in concrete modeling and degrading effects in steel modeling, which substantially affects the monotonic, cyclic and seismic responses of RC members and frames. Based on the system level analysis, it is shown that the response of non-ductile frames is less sensitive to confined concrete models while the modeling of reinforcing steel is quite influential to the inelastic response of both non-ductile and ductile frames.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.1-4
• /
• 2002

The present study aims to design a multiplayer microstrip antenna with composite sandwich construction and to estimate structural behavior of this multiplayer structure for the next generation of structural surface technology. This is termed Surface-Antenna-Structure indicating that structural surface becomes antenna. Constituent materials were selected considering electrical properties as well as mechanical properties. For the antenna performance, antenna elements inserted into structural layers were designed for satellite communication at a resonant frequency of 12.5 GHz and final demonstration article was $16\times16$ array antenna. From electrical measurements it was shown that antenna performances were in good agreement with design requirements. Structural analysis showed this antenna structure was well designed for the mechanical rigidity. All constituent materials were characterized independently. The SAS concept is the first serious attempt at integration for both antenna and composite engineers and promises innovative future communication technology.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.5-5
• /
• 2011

Lithium ion batteries are found to have wide range of applications in variety of mobile devices ranging from simple toys to electric vehicles. The performance of these batteries depends on the choice of constituent materials. In this lecture, the materials aspects and perspectives of the electrode batteries will be discussed. Results from some of the specific studies made at speaker's laboratory will be presented.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.10a
• /
• pp.162-165
• /
• 1998

Characteristics of microcapsule wall depend on chemical and physical condition in procedure such as type and concentration of constituent and microencapsulation methods, thus, if the other process conditions are same, they depend on mainly types of wall-forming materials. Isocyanates used in this study are very important constituent as hard segments preparing urethane or urea by reaction with alcohol or amine. (omitted)

• Korean Journal of Materials Research
• /
• v.31 no.8
• /
• pp.433-438
• /
• 2021

In this study, microstructural characteristics and constituent elements of fiberglass splint and cast are examined using a scanning electron microscope and an energy dispersive X-ray spectrometer. As observed by the scanning electron microscope, fiberglass splint and cast had a porous structure with many bundles of fiberglass textures well assembled. Spaces between bundles of the fiberglass splint are triangular or elliptical shaped and the long-axis diameter is measured at about 1 mm. The thickness of fiber bundles covered with plaster is measured at 600 ㎛ and the diameter of a single strand of fiberglass is up to 10 ㎛. The thickness of the fiberglass bundle of the fiberglass splint is measured at about 700 ㎛. Spaces between bundles are formed in the shape of triangles with gentle edges and long-axis diameter of up to 1.4 mm, which is larger than that of the splint. The thickness of a single strand of fiberglass of the plaster-coated cast is 11.5 ㎛, which is thicker than that of fiberglass of the splint. As a result of analyzing constituent elements of the fiberglass cast and the splint with an energy dispersive X-ray spectrometer, Ca, Si, and Al components are identically detected. This result shows that the fiberglass cast has a smoother surface with hardened plaster than the fiberglass splint. The thickness of the fiberglass bundle and the thickness of a single strand of the fiberglass are also larger than those of the fiberglass splint.