• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.5
• /
• pp.411-414
• /
• 2004

In this paper, a power controller and 3 phase voltage source inverter are proposed for the improvement of weldability of large scaler Mash seam welder. The welder system is designed for the low cost and the improvement of weldability. For this system, the thyristor convertor has performed constant current controlling in the output terminal by using PAM type inverter. We have simulated our algorithm and made a prototype welder for experiment. Through the experiment, we have confirmed the improvement of weldability of our system.

• 전기의세계
• /
• v.15 no.4
• /
• pp.18-21
• /
• 1966

A transistorized counting-rate meter was designed by substituting one of diodes in the ordinary diode pumping circuit by the Darling's constant current source. Its circuit is so simple and stable that it is proper to use as a part of portable radiation detectors. Maximum readable counting rate is well above 100 kc/s and the linearity is very good. Output deviations due to the variations of embient temperatures are less than 5% in the temperatures from 20.deg. C to 40.deg. C.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.22-24
• /
• 1995

The electrical conductivity of TiO$_2$doped ZnO was investigated by means of complex impedance measurement and voltage-current source and meaurement unit. The e1ectrical conductivity of TiO$_2$added ZnO was increased with increasing the concentration of TiO$_2$. The calculated relative dielectric constant was decreased with increasing the concentration of TiO$_2$. The increase of electrical conductivity seems to be the effect of TiO$_2$donor doping.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.10-10
• /
• 2010

The solar cell energy is considered as a clean energy source in the world. However, because the output of solar cell is not constant, it needs to study the relationships of the DC voltage, the DC current and the DC power of the solar cell. This paper presents the solar cell output characteristics and the maximum power point of the solar cell under different irradiation conditions.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.65-67
• /
• 2002

The gas metal arc welding(GMAW) is regarded as one of the best candidate for welding automation in industrial joining application. It is important to monitor the weld quality for the high performance of weld automation. The measured analog signal is frequency analyzed by digital signal process method. In order to observe the welding phenomena and control welding condition, arc light, voltage, and current are measured at the same time. They are analyzed and compared with arc sound. for these experiments, a power source of constant voltage characteristics was used in the pure metal transfer mode.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.106-117
• /
• 1998

Fluorocarbonated-SiO2 films were deposited on p-type Si(100) substrate using FSi$(OC_2H_5)_3$ (FTES), and $O_2$ mixture gases by a helicon plasms source. High density $O_2$/FTES/Ar plasma of ~$10^{12} \textrm{cm}^{-3}$ is obtained at low pressure (<3mTorr) with RF power above 900 W in the helicon plasma source. Optical emission spectroscopy (OES) is used to study the relation between the relative densities of the radicals and the film properties. The FTES and $O_2$ gases are greatly dissociated at the helicon mode that is launched at the above threshold plasma density. FTIR and XPS spectra shows that the film has Si-F, and C-F bonds during the formation process of the film which may lower the dielectric constant greatly. The relative dielectric constant, leakage current density, and dielectric breakdown voltage are about 2.8, $8\times10^{-9}\textrm{A/cm}^2$, and > 12 MV/cm, respectively.

• Current Optics and Photonics
• /
• v.7 no.6
• /
• pp.701-707
• /
• 2023

In laser imaging, accurate extraction of the laser's center is essential. Several methods exist to extract the laser's center in an image, such as the geometric mean, the parabolic curve fitting, and the Gaussian curve fitting, etc. The Gaussian curve fitting is the most suitable because it is based on the physical properties of the laser. The width of the Gaussian laser beam depends on the distance from the laser source to the target object. It is assumed in general that the distance remains constant at a laser spot resulting in a symmetric Gaussian model for the laser image. However, on a curved surface of the object, the distance is not constant; The laser beam is narrower on the side closer to the focal point of the laser light and wider on the side closer to the laser source, which causes the distribution of the laser beam to skew. This study presents a modified Gaussian model in the laser imaging to incorporate the slant angle of a curved object. The proposed method is verified with simulation and experiments.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.48-48
• /
• 2009

Conventionally in pulsed gas metal arc welding (GMAW-P), drop transfer is analyzed with simplest square pulse waveform. While the pulse current is described by four parameters (peak current magnitude and time plus base current magnitude and time), it deviates the real pulse shape. Real pulse can be better idealized by the trapezoidal pulse waveform described by two additional parameters, i.e., current rise and fall rate (dI/dt). Power source response rate is described by these parameters. In this work, the effect of these parameters on drop transfer is predicted by the force displacement model (FDM). While peak current has significant effects on drop detachment, drop transfer is also influenced by the current rise rate. Predictions indicate that the current rise rate can have considerable effects on the size of the detached drop if other pulse parameters are kept constant. FDM is applied to determine peak time for one drop one pulse condition (ODOP) when rests of the pulse parameters are given. The predicted range of ODOP shows good agreement with experimental data.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.1
• /
• pp.61-69
• /
• 1998

In this paper, discrete current control of voltage source inverters is proposed. As a current control scheme, the constant switching frequency predictive current control is adopted and implemented with DSP microprocessor system. In particular, the proposed method is for the compensation of the control lagging due to calculation delays in the microprocessor controller. In controlling the current, the inverter output voltage saturation problem is inevitable and usually affects the current control performance. So, the saturation boundary condition of the inverter output voltage and its effects on the current controal performance of the proposed current control scheme are investigated with experiment. Finally, the proposed scheme is applied to the active power filter system and some results are described for validation.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.265-267
• /
• 2001

In this paper, some optical parameters which have effects on the measuring precision and sensitivity of optical current sensor are analyzed. Each parameter occurs changes of specific characteristics of optical sensor system. The influences of performance and characteristics variation of optical current sensor are described in accordance with the changes of optical output power, optical bias point which is called phase difference, and a specific constant related to sensor material and wavelength of light source.