• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.174-179
• /
• 2004

Attenuation of conduction noise through microstrip line attached with the high lossy iron flakes-rubber composites has been investigated in GHz frequencies. Microstrip line was designed with characteristic impedance of 50 $\Omega$ and a length corresponding to the center frequency of 3 GHz. Iron flakes were fabricated by mechanical forging of spherical iron powders using an attrition mill. The fabricated microstrip line shows a ideal propagation characteristics of S$\sub$11/ < -60 dB and S$\sub$21/ = 0 dB. Attaching a noise absorbing sheet on the microstrip line, S$\sub$11/ increases to about -10 dB and S$\sub$21/ decreases to -20～-60 dB depending on the length of absorbing sheet. The calculated power loss is as high as 80% in the frequency range 2～8 GHz. It is suggested that the most critical material parameter is magnetic loss for the enhancement of noise attenuation.

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.242-245
• /
• 2007

Conduction noise attenuation by composite sheets of high magnetic and dielectric loss has been analyzed by using electromagnetic field simulator which employs finite element method. The simulation model consists of microstrip line with planar input/output ports and noise absorbers (magnetic composite sheets containing iron flake particles as absorbent fillers). Reflection and transmission parameters $(S_{11}\;and\;S_{21})$ and power loss are calculated as a function of frequency with variation of sheet size and thickness. The simulated value is in good agreement with measured one and it is demonstrated that the proposed simulation technique can be effectively used in the design and characterization of noise absorbing materials in the RF transmission lines.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.85-91
• /
• 2022

This study proposes a high efficiency bridgeless Power Factor Correction (PFC) converter with improved common mode noise characteristics. Conventional PFC has limitations due to low efficiency and enlarged heat sink from considerable conduction loss of bridge diode. By applying a Common Mode (CM) coupled inductor, the proposed bridgeless PFC converter generates less conduction loss as only a small magnetizing current of the CM coupled inductor flows through the input diode, thereby reducing or removing heat sink. The input diode is alternately conducted every half cycle of 60 Hz AC input voltage while a negative node of AC input voltage is always connected to the ground, thus improving common mode noise characteristics. With the aim to improve switching loss and reverse recovery of output diode, the proposed circuit employs Critical Conduction Mode (CrM) operation and it features a simple Zero Current Detection (ZCD) circuit for the CrM. In addition, the input current sensing is possible with the shunt resistor instead of the expensive current sensor. Experimental results through 480 W prototype are presented to verify the validity of the proposed circuit.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.5
• /
• pp.423-429
• /
• 2013

The present study aimed to find the most sensitive placement of the skull to perceive speech through the bone vibrator in various protection methods while being exposed to noise. Twenty young normal-hearing adults (10 male and 10 female) participated in the study. As stimulus, Korean spondee words were presented via one of five skull locations (i.e., jaw angle, condyle, temple, mastoid, and vertex), while the participants wore one of four protection methods (i.e., ear form, ear plug, ear muff, and ear form and muff together) against white noise in one of four noise directions (i.e., 0, 90, 180, 270 degrees). The results showed: 1) there was a significant difference among the five skull locations with condyle being the most sensitive placement; 2) there was a significant difference among the four protection methods, with the ear form plus ear muff condition (or dual protection) providing the lowest threshold; 3) when exposed to noise from 90 degrees, the significantly lowest threshold was found; 4) there was no significant difference in results by gender. The pattern of results suggests that the communicative condition via the condyle bone conduction and the dual protection of the air conduction under any noise direction might be ideal for preventing noise-induced hearing loss, although further studies should be undertaken in this area.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.1064-1069
• /
• 1994

In order to realize the function of human interface of telecommunications whose objective is to interchange useful information among persons, we developed a bone conduction telephone with which hearing impaired persons with conductive or noise-induced hearing loss and presbycusis can communicate with each other without any other additional devices such as hearing aids. The bone conduction telephone we developed has chatacteristics as follows : (i) a hearing impaired person and a normal hearing person can communicate by bone and air conduction hearings, respectively, using only this telephone set because, as its receiver, it uses a bone conduction vibrator with which we can realize such function with the voice coil and damper of a small speaker unit, the vibrating plate, etc., (ii) it has tone control function compensating hearing losses of hearing impaired persons according to their hearing loss/frequency chatacteristics. Using the tone control function together with a received volume control, it has the received volume range of 20dB in loudness rating; and (iii) it has the function of three emergency calls and a bell lamp as the visual display of a received call.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.794-796
• /
• 1993

This paper deals with the characteristic analysis of noise filter for the reduction of conduction noise, especially, common-mode noise. Attenuation in the system containing noise filter is analyzed and equivalent circuits for common- and differential- mode noise are derived. To clarify the effects by parasitic components of the inductor and capacitor, digital simulations using Design Center are carried out.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.613-617
• /
• 2008

One of the important parts on multimedia era is acoustic ones. With increased demand of smallest multimedia products such as personal digital assistant (PDA) and mobile phones, it is necessary to develop acoustic devices which have higher performance and smaller size. Acoustic parts with various function for hearing impaired persons. This paper introduces a bone conduction vibrator (BCV) for hearing impaired persons to use portable acoustic device without additional devices. For vibration analysis of the BCV, electromagnetic, mechanical and their coupling effects are considered for the analysis. This paper shows that the development of design and analysis technique by finite element method (FEM) of BCV.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.6
• /
• pp.665-670
• /
• 2011

In this paper, a new approach to detect surface cracks from a noisy thermal image in the infrared thermography is presented using an holomorphic characteristic of temperature field in a thin plate under steady-state thermal condition. The holomorphic function for 2-D heat flow field in the plate was derived from Cauchy Riemann conditions to define a contour integral that varies according to the existence and strength of a singularity in the domain of integration. The contour integral at each point of thermal image eliminated the temperature variation due to heat conduction and suppressed the noise, so that its image emphasized and highlighted the singularity such as crack. This feature of holomorphic function was also investigated numerically using a simple thermal field in the thin plate satisfying the Laplace equation. The simulation results showed that the integral image selected and detected the crack embedded artificially in the plate very well in a noisy environment.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.296-306
• /
• 2019

The flyback topology is being widely used in power adapters. The coupling capacitance between primary and secondary windings of a flyback transformer is the main path for common-mode (CM) noise conduction. A Y-cap is usually used to effectively suppress EMI noise. However, this results in problems in space, cost, and the danger of safety leakage current. In this paper, the CM noise behaviors due to the electric field coupling of the transformer windings in a flyback adapter with synchronous rectification are analyzed. Then a scheme with balance winding is proposed to reduce the CM noise with a transformer winding design that eliminates the Y-cap. The planar transformer has advantages in terms of its low profile, good heat dissipation and good stray parameter consistency. Based on the proposed scheme, with the help of a full-wave simulation tool, the key parameter influences of the transformer PCB winding design on CM noise are further analyzed. Finally, a PCB transformer for an 18W adapter is designed and tested to verify the effectiveness of the balance winding scheme.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.288-288
• /
• 2009

Most of Static electricity forms part of our daily experience broadly. Most people have noticed from time to time electric shocks when closing of their car or after walking across a carpet, operating shredder in winter and touching a metal handle. This electrostatic discharge nuisance is normally a minor inconvenience, but in some cases static electricity can cause more serious problems. Static electricity can also be harnessed to good effect in Position Control System.