• Computers and Concrete
• /
• v.12 no.5
• /
• pp.651-668
• /
• 2013

Concrete structures need repairing due to various reasons such as deteriorative effects, overloading, poor quality of workmanship and design failures. Cement based repair mortars are the most widely used solutions for concrete repair applications. Various factors may affect the bond strength between concrete substrate and repair mortars. In this paper, the effects of polymer additives, strength of the concrete substrate, surface roughness, surface wetness and aging on the bond between concrete substrate and repair mortar has been investigated. Full factorial experimental design is employed to investigate the main and interaction effects of these factors on the bond strength. Analysis of variance (ANOVA) under design of experiments (DOE) in Minitab 14 Statistical Software is used for the analysis. Results showed that the interaction bond strength is higher when the application surface is wet and strength of the concrete substrate is comparatively high. According to the results obtained from the analysis, the most effective repair mortar additive in terms of bonding efficiency was styrene butadiene rubber (SBR) within the investigated polymers and test conditions. This bonding ability improvement can be attributed to the self-flowing ability, high flexural strength and comparatively low air content of SBR modified repair mortars. On the other hand, styrene acrylate rubber (SAR) modified mortars was found incompatible with the concrete substrate.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.89-94
• /
• 1997

As the reinforced concrete structures are aged, repair and rehabilitation materials and techniques have ben developed. However, most of the repair materials and methods are imported from abroad and theoretical study and repairing techniques are also not well established yet. A specification for quality of repair materials should be established, in order to secure the stability and to improve the serviceability of the repaired structures. In this study, long term properties of repair materials such as thermal expansion coefficient, hardening shrinkage, creep, and chemical resistance have been tested. The material properties shows to be affected many actors such as curing period, temperatures, relative humidity, and etc. The repair material should be selected by considering the cause and shape of the defects, mix properties, workability, quality control of construction, and etc.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.709-714
• /
• 1997

Recently, the repair materials for defected RC structures are being developed and the performance on repaired RC structures are being studied. This experiment is aimed to evaluate the flexural performance of the RC beams repaired by premix-type materials. The parameters used in this study is the repair materials, the repair length and the treatment of interface. Flexural capacity of repaired RC beams except the polymer-repaired RC beams are similar to that of the control beam. In the flexural capacity, the RC beams treated with chipping show better results than the RC beam without chipping. The various repair lengths of the repaired RC beam are not affected to the flexural capacity.

• Computers and Concrete
• /
• v.7 no.3
• /
• pp.249-269
• /
• 2010

Managing and reusing knowledge in engineering and construction sectors can lead to greater competitive advantage, improved designs, and more effective management of constructed facilities. The use of Information Technology (IT) in design and construction can exploit strategic opportunities for new ways of integration, sharing and facilitating information and knowledge in any field of engineering. The integrating of separate areas of IT can be used to bring a group of experts and specialists in any field of engineering closer together by allowing them to communicate and exchange information and expertise that facilitate knowledge capture, sharing, and reuse. A lack of an advisory management system and a need to marshal all available data in a common format has indicated the need for an integrated engineering computing environment to investigate concrete repair problems. The research described in this paper is based upon an evaluation management system (EMS) which comprising a database management system (REPCON) alongside visualisation technologies and evaluation system (ECON) is developed to produce an innovative platform which will facilitate and encourage the development of knowledge in educational, evolution and evaluation modes of concrete repair. This allows us to create assessment procedures that will allow the current condition of the concrete structure and its components to be expressed numerically using a confidence level (CL) so as to take the best course of action in the repair and maintenance management. The explained rating system, which is related to structural integrity and serviceability of the structure, allows the confidence level to be determined by visual inspection and the descriptive information and pictures taken from an available REPair of CONcrete (REPCON) database.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.885-892
• /
• 2005

Recently, the damaged concrete structures are often strengthened or repaired using the polymer concrete or the polymer cement mortar. In the repaired concrete structures at early ages, internal stresses could be developed due to the differential drying shrinkage of the repair material. Due to the difference of the thermal coefficients of the repair material and existing concrete, additional stresses also could be developed as the structures are subjected to the ambient temperature changes. Theses environmentally-induced stresses can sometimes be large enough to cause damage to the structures, such as debonding of the interface between the two materials. In this study, a rational procedure was developed where anchors can be designed and installed to prevent damages in such structures by thermally-induced stresses. Finally, through the experimental study and numerical study, the effects of the repair method using anchors with debonding was investigated and discussed the results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.133-136
• /
• 2006

The main purpose of this study is to develop a Sprayed FRP repair and strengthening method, which is a new technique for strengthening the existing concrete structures by mixing carbon or glass shot fibers and the epoxy or vinyl ester resins with high-speed compressed air in open air and randomly spraying the mixture onto the concrete surface. At present, the Sprayed FRP repair and strengthening method using the epoxy resin has not been fully discussed. In this study, a series of experiments are carried out to evaluate the strengthening effects of the flexural and shear concret beams strengthened with the Sprayed FRP method. The results revealed that the strengthening effects of the flexural and shear specimens are similar, compared to those of the FRP sheet.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.822-825
• /
• 2004

Corrosion of reinforced concrete structures in marine environment is one of the most important mechanism of deterioration. The conventional repair techniques of concrete structure damaged by chloride attack consist of removing damaged concrete, cleaning rebar and patching with cement-based materials. However, recently, this method was considered to be ineffective for marine concrete structure in tidal zone. It is necessary to select proper repair method for domestic marine environment which shows broad tidal zone. This paper reports the results of repair of highway concrete bridge damaged by chloride attack in domestic marine environment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.191-197
• /
• 2006

This study is to establish a standardization of injection system by inorganic material for crack repair of tunnel concrete structures. For this various surveys and experiments were carried out as followed. The first we surveyed capability of injection and crack pattern of concrete structures in site. and second we analyzed the relationship between crack width and volume of injection, and decided pressure and volume of injection. Finally we evaluated the relationship between crack width and volume of injection with kind of concrete structures, and between required time for injection and crack width with thickness of structure. From these surveys and experiments, we cleared the relationship between crack patterns and injection technologies such as volume, pressure of injection and required time for injection with kind of structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.212-218
• /
• 1995

This study experimentally evaluated the performance of damaged section which was repaired using polymer materials in reinforced flexural flexural members Six different materials, two types of polymer, two types of polymer-cement and two types of cement, were used by means of injection method on prepacked concrete and spray mortar patching method. As results, the repair works could be done easily and surfaces of the repaired section were smooth.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.47-48
• /
• 2023

Reinforced concrete structures are an integrated structure in which reinforcing bars are placed on the tensile side of the beam to compensate for concrete that is strong in compression but weak in tension, so that the concrete receives compressive force and the reinforcing bars receive tensile force. It is durable, fire-resistant, economical, and adapts to the shape and dimensions of the structure. It has been widely used for a long time because it can be made freely without restrictions. However, reinforced concrete structures have the disadvantage that cracks occur easily, so they are repaired using a cross-sectional construction method. During this process, problems such as the repair part falling off occurred, so in order to solve the problem, stress changes due to changes in the size of the repair part were examined. As a result, based on the elastic modulus ratio of 1.0, the stress tended to increase as the size of the repair part decreased when it was less than 1.0, and the opposite tendency was seen when it was more than 1.0. This is believed to be due to an increase in the area of the part with a large elastic modulus.