• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.108-113
• /
• 2004

The compressive axial collapse tests were performed to investigate energy absorption characteristics of Al/CFRP compound tubes which are aluminum tubes wrapped with CFRP (Carbon Fiber Reinforced Plastics) outside the aluminum circular and square tubes. Based on collapse characteristics of aluminum tubes and CFRP tubes respectively, the axial collapse tests were performed for Al/CFRP compound tubes which have different fiber orientation angles. Test results showed that Al/CFRP compound tubes supplemented the unstable brittle failure of CFRP tubes due to ductile nature of inner aluminum tubes. In the light-weight aspect, specific energy absorption were the highest for Al/CFRP, CFRP in the middle, and aluminum the lowest. Also, specific energy absorption of circular tubes was higher than square tubes'. It turned out that fiber orientation angle of Al/CFRP compound tubes influence specific energy absorption together with the collapse modes of the tubes.

• 한국재료학회지
• /
• 제31권1호
• /
• pp.38-42
• /
• 2021

In this study, high temperature wetting analysis and AZ80/Ti interfacial structure observation are performed for the mixture of AZ80 and Ti, and the effect of Al on wetting in Mg alloy is examined. Both molten AZ80 and pure Mg have excellent wettability because the wet angle between molten droplets and the Ti substrate is about 10° from initial contact. Wetting angle decreases with time, and wetting phenomenon continues between droplets and substrate; the change in wetting angle does not show a significant difference when comparing AZ80-Ti and Mg-Ti. As a result of XRD of the lower surface of the AZ80-Ti sample, in addition to the Ti peak of the substrate, the peak of TiAl3, which is a Ti-Al intermetallic compound, is confirmed, and TiAl3 is generated in the Al enrichment region of the Ti substrate surface. EDS analysis is performed on the droplet tip portion of the sample section in which pure Mg droplets are dropped on the Ti substrate. Concentration of oxygen by the natural oxide film is not confirmed on the Ti surface, but oxygen is distributed at the tip of the droplet on the Mg side. Molten AZ80 and Ti-based compound phases are produced by thickening of Al in the vicinity of Ti after wetting is completed, and Al in the Mg alloy does not affect the wetting. The driving force of wetting progression is a thermite reaction that occurs between Mg and TiO2, and then Al in AZ80 thickens on the Ti substrate interface to form an intermetallic compound.

• 한국육종학회지
• /
• 제40권2호
• /
• pp.143-152
• /
• 2008

1913년부터 2000년까지 국내에서 육성된 70품종에 대한 초형형질에 관련된 주경, 분지 및 엽형질의 특성을 파악하여 다수성 콩 품종개발의 기초자료로 이용코자 하였다. 1. 초형형질의 변이는 주경과 분지관련형질의 12개 형질 중에서 초형폭, 분지장 및 초형폭/장 비율이 컸으며, 엽관련 8개형질 중에서는 엽병각, 엽장폭비 및 엽건물중이 컸다. 2. 용도별로 초형폭/장 비율은 밥밑콩이 장류 및 두부용콩과 나물콩에 비하여 높았고 장류 및 두부용콩과 나물콩은 큰 차이가 없었다.총분지장/주경장 비율은 나물콩과 밥밑콩이 높았고 장류 및 두부용콩이 낮았다. 3. 주경과 분지형질은 초형폭/장 비율과 총분지장/ 주경장 비율에 의하여 각각 그룹으로 분류되어졌고, 협초폭형이며 주경의존형은 단원콩, 금강콩, 셀비 및 신팔달콩이었고, 협초폭형이며 분지의존형은 소명콩이었다. 광초폭형이면서 주경의존형은 강림, 금강대립 및 진율콩이었으며, 광초폭형이면서 분지의존형은 검정콩 2호이었다. 4. 용도별로 소엽장/폭 비율은 밥밑콩이 작았고 장류 및 두부용콩과 나물콩과는 큰차이가 없었으며, 복엽의 엽면적은 밥밑콩이 가장 컸고 나물콩이 가장 작았다. 엽병장은 나물콩이 작았으며 장류 및 두부용콩과 밥밑콩은 큰 차이가 없었고, 엽병각은 밥밑콩이 가장 컸고 나물콩이 가장 작았다. 5. 엽형태는 엽장폭비와 엽면적에 의하여 각각 4그룹으로 분류 되어졌고, 소엽장폭비가 큰 원엽이면서 엽면적이 큰 대형엽은 부석과 대황콩이었고, 엽장폭비가 극세엽이면서 엽면적이 작은 소형엽은 은하콩과 소호콩이었다. 6. 엽병의 특성은 엽병장과 엽병각에 의하여 각각 3그룹과 4그룹으로 분류 되어졌고, 엽병장이 짧고 엽병각이 작은 품종은 은하콩이었고, 엽병장이 짧고 엽병각이 큰 품종은 알찬콩, 무한콩 및 푸른콩이었으며, 엽병장이 길고 엽병각이 작은 품종은 신팔달콩 2호이었다. 7. 은하콩은 전 시험품종 중에서 엽장폭비가 가장 큰 극세엽이면서 엽면적이 가장 작은 소형엽이었고, 엽병장이 가장 짧으며 엽병각이 가장 작은 품종이었다.

• 한국광학회지
• /
• 제34권1호
• /
• pp.13-21
• /
• 2023

입사하는 빛에 대한 수용각이 큰 인공 겹눈 구조를 제작하기 위해 마이크로 렌즈 어레이의 높이에 따라 곡면형 겹눈 구조체가 갖는 수용각과 이미징 특성을 분석하였다. 마이크로 렌즈의 반지름에 대한 높이인 h/r값을 조절함으로써 보다 큰 입사각을 갖는 빔이 마이크로 렌즈 어레이로 들어올 때도 여전히 빔을 포커싱하고 이미지를 맺을 수 있는 렌즈의 구조를 확인하였다. h/r값이 0.22에서 0.37로 증가할 때 겹눈 구조체의 수용각은 28.70°에서 49.02°로 증가하여 70.8%의 증가폭을 얻어낼 수 있었다. 뿐만 아니라 글자 F를 이미징한 결과, h/r값이 0.37일 때 메인 렌즈의 중심으로부터 23번째에 위치한 마이크로 렌즈에서도 글자가 선명하게 관찰되어 56.35°의 입사각을 갖는 빔에 대해서도 마이크로 렌즈 어레이가 이미지를 맺을 수 있음을 확인하였다.

• 한국광학회지
• /
• 제10권6호
• /
• pp.500-506
• /
• 1999

레이저 다이오드와 수신광검출기가 집적된 소자를 V-홈을 가진 실리콘 광학벤치에 flip-chip 본딩하고, 경사면을 가진 하나의 단일모드 광섬유와 수동정렬하는 방법을 사용하여 가입자망을 위한 저가의 양방향 송수신 모듈을 설계, 제작하였다. 광섬유의 단면 경사각에 따른 송신광결합 효율과 수신광결합 효율사이의 병목점을 찾기 위해 Gaussian빔 모델을 사용하여 수평정렬거리, 광섬유 단면 경사각, 수직정렬오차등의 변수에 따른 광결합계수를 계산함으로써, 최적의 광정렬조건을 예측하였다. 또한 실리콘 광학벤치에서 광결합효율을 측정하여 광섬유의 수직정렬오차에 따른 광결합계수의 감소가 광섬유의 경사각에 의해 보상될 수 있다는 계산결과의 타당함을 확인하였다. 실제의 sub-module 제작 및 광결합 실험에서 송신빔이 광섬유 단면에 반사되어 PD로 입사되는 것을 최소화하기 위하여 광섬유 단면을 경사절두원추형으로 제작함으로써 PD의 수신 잡음을 $30mu$m 이상의 정렬거리에서 -35dB이하로 유지할 수 있었다. 같은 조건에서 단면 경사각이 $12^{\circ}$인 광섬유에 의해 -12.1dB의 송신출력과 0.2A/W의 responsivity를 얻을 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.103-110
• /
• 2000

A two phase compound jet, which mixes pulverized solid particles with the air in the test section, is experimentally analyzed in this study. Two phase flow is jetted 10 degree upward in the primary jet, while the secondary jet utilizes the air only. The height difference between the primary and secondary central axises is 32.5mm. The velocity vector field, concentration field, and turbulent properties of solid particles are measured by using 3-Dimensional Particles Dynamics Analyzer. When the jet angle of the secondary jet goes into effect, the solid particle recirculation zone becomes larger. Also, solid particle concentration becomes more dense due to a velocity decrement of particles.

• 전기화학회지
• /
• 제7권2호
• /
• pp.80-82
• /
• 2004

The a.c. technique is employed to evaluate electrochemical characteristics of Naphthalie-1,4,5,8-tetracarboxylic acid bisanilide (NTB). The measurements were carried out in dry and pure propionitrle (PCN) and acetonitrile(CAN) at the hanging mercury drop electrode [HMDE). An A.C. phase sensitive detector using computer controlled lock-in amplifier was employed. Primary goal of this report, was to establish on a firm the rare behavior of the phase angle associated with a.c. polarograms of the compound. Although, not an initial goal of this study, the electron transfer rate parameters attending the electroreduction of the compound under investigation were determined. This because the results shed some light on the electrokinetics in aprotic solvent which until recently negligible data were available. Experimental Results and comparison of data obtained are reported. The good precision of the method makes it suitable for studying electrochemical data with unusual behavior at electrodes in non aqueous media.

• 대한기계학회논문집A
• /
• 제28권11호
• /
• pp.1768-1775
• /
• 2004

The compressive axial collapse tests were performed to investigate collapse modes and energy absorption characteristics of Al/CFRP compound tubes which are aluminum tubes wrapped with CFRP(Carbon Fiber Reinforced Plastics) outside the aluminum circular and square tubes. Based on collapse characteristics of aluminum tubes and CFRP tubes respectively, the axial collapse tests were performed for Al/CFRP compound tubes which have different CFRP orientation angles. Test results showed that Al/CFRP compound tubes supplemented the unstable brittle failure of CFRP tubes due to ductile nature of inner aluminum tubes. In the light-weight aspect, specific energy absorption were the highest for Al/CFRP, CFRP in the middle, and aluminum the lowest. Also, specific energy absorption of circular tubes was higher than square tubes'. It turned out that CFRP orientation angle of Al/CFRP compound tubes influence specific energy absorption together with the collapse modes of the tubes.

• Current Optics and Photonics
• /
• 제5권6호
• /
• pp.699-710
• /
• 2021

In this study, we propose a biomimetic optical structure design methodology for investigating micro-optical mechanisms associated with the compound eyes of insects. With these compound eyes, insects can respond fast while maintaining a wide field of view. Also, considerable research attention has been focused on the insect compound eyes to utilize these benefits. However, their nano micro-structures are complex and challenging to demonstrate in real applications. An effectively integrated design methodology is required considering the manufacturing difficulty. We show that photorealistic ray-traced visualization is an effective method for designing the biomimetic of a micro-compound eye of an insect. We analyze the image formation mechanism and create a three-dimensional computer-aided design model. Then, a ray-trace visualization is applied to observe the optical image formation. Finally, the segmented images are stitched together to generate an image with a wide-angle; the image is assessed for quality. The high structural similarity index (SSIM) value (approximately 0.84 to 0.89) of the stitched image proves that the proposed MATLAB-based image stitching algorithm performs effectively and comparably to the commercial software. The results may be employed for the understanding, researching, and design of advanced optical systems based on biological eyes and for other industrial applications.

• Transactions on Electrical and Electronic Materials
• /
• 제16권3호
• /
• pp.112-116
• /
• 2015

This work studied the thickness and contact angle of solder joints between SAC 305 lead-free solder alloy and a Copper (Cu) substrate. Intermetallic compound (IMC) thickness and contact angle of 3Sn-Ag-0.5Cu (SAC 305) leadfree solder were measured using varying aging times, at a fixed temperature at 30℃. The thickness of IMC and contact angle depend on the aging time. IMC thickness increases as the aging increases. The contact angle gradually decreased from 39.49° to 27.59° as aging time increased from zero to 24 hours for big solder sample. Meanwhile, for small solder sample, the contact angle increased from 32.00° to 40.53° from zero to 24 hours. The IMC thickness sharply increased from 0.007 mm to 0.011 mm from zero to 24 hours aging time for big solder. In spite of that, for small solder the IMC thickness gradually increased from 0.009 mm to 0.017 mm. XRD analysis was used to confirm the intermetallic formation inside the sample. Cu₆Sn₅, Cu₃Sn, Ni₃Sn and Ni₃Sn₂ IMC layers were formed between the solder and the copper substrate. As the aging time increased, the strength of the solder joint mproved due to reduced contact angle.