• 멤브레인
• /
• 제27권2호
• /
• pp.182-188
• /
• 2017

본 연구에서는 고분자 전해질 연료전지(PEFC)의 전해질막의 화학적 안정성의 향상을 위하여 3-mercaptopropyl silica gel (3MPTSG)과 poly(arylene ether sulfone)(SPAES)을 이용하여 복합막을 제조하였다. 일반적으로 방향족 탄화수소계 고분자막은 전극 부분에서 발생한 라디컬에 의한 고분자 산화가 일어나 내구성이 감소하게 되는데 이는 대부분 주쇄에 포함된 에테르 기 부분의 취약성으로 발생한다. 본 연구에서는 이러한 라디칼에 의한 고분자 주쇄의 산화를 방지하기 위해 친수성의 무기물 입자를 도입하여 이온전도도 감소율을 최소화하고 산화안정성을 높이고자 하였다. 복합막들의 물성 및 전기화학적 특성을 평가하기 위해 접촉각, FT-IR, 이온전도도, 이온교환용량(IEC), 함수율, 열안정성 등을 수행하였다. 실리카의 함량이 0에서 0.5%까지 증가함에 따라 이온전도도 및 함수율은 각각 10% 감소한 0.076 S cm-1 및 16% 감소한 24.6 wt%이었으나, 산화안정성은 10% 향상되었다.

• 한국입자에어로졸학회지
• /
• 제12권4호
• /
• pp.127-134
• /
• 2016

A multiwall carbon nanotube (MWCNT)/graphene (GR) composite was synthesized for an enhanced supercapacitor. Aerosol spray pyrolysis (ASP) was employed to synthesize the MWCNT/GR composites using a colloidal mixture of MWCNT and graphene oxide (GO). The effect of the weight ratio of the MWCNT/GO on the particle properties including the morphology and layered structure were investigated. The morphology of MWCNT/GR composites was generally the shape of a crumpled paper ball, and the average composite size was about $5{\mu}m$. MWCNT were uniformly dispersed in GR sheets and the MWCNT not only increase the basal spacing but also bridge the defects for electron transfer between GR sheets. Thus, it was increasing electrolyte/electrode contact area and facilitating transportation of electrolyte ion and electron in the electrode. Electrochemical data demonstrate that the MWCNT/GR (weight ratio=0.1) composite possesses a specific capacitance of 192 F/g at 0.1 A/g and good rate capability (88% capacity retention at 4 A/g) using two-electrode testing system.

• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.391-402
• /
• 1999

Characteristics of composite electrolytes which were prepared by coating a thin film of YSZ (yttria sta-bilized zirconia : (ZrO2)0.92 (Y2O3)0.08) on YDC (yttria doped ceria : Ce0.8Y0.2O1.9) with mixed conductivity have been investigated in order to develop the low-temperature solid oxide fuel cell. The thickness (t) of spin-coated YSZ thin films after the heat-treatment at 600$^{\circ}C$ was increased proportionally to the sol con-centrations (C) while the decrease in its thickness with the spin rate ($\omega$) could be expressed in the e-quation of ln t=9.49-0.53 ln $\omega$(0.99mol//s sol conc.) When the sol concentration and the spin rate being less than 0.99 mol/l and higher than 1000 rpm respectively reliable YSZ/YDC composite electrolytes could be obtained by multi-coating although several micro-cracks were observed in singly coated YSZ film surfaces. The dense YSZ film with a 1$\mu\textrm{m}$ thickness was prepared by coating of 0.99 mol/l YSZ sol five-times at 2000 rpm followed by heat-treatment at 1400$^{\circ}C$ for 2h, The adhesion between YSZ film and YDC substrate was found to be very good. The open circuit voltages of H2/O2 single cell with YSZ/YDC composite electrolytes were 0.79∼0.82 V at 800$^{\circ}C$ and 0.75∼0.77V at 900$^{\circ}C$ The open circuit voltage was inversely proportioned to the thickness ratio of YSZ thin film (1$\mu\textrm{m}$) to YDC substrate(0.28-2.22 mm)

• 한국표면공학회지
• /
• 제25권2호
• /
• pp.73-81
• /
• 1992

The composite coating of suspended inert particles $\alpha$-Al2O3 and copper from acid sulphate bath was investigated at the Rotating Disk Electrode. Effects of rotation speeds of electrode, physical properties of electrolyte, the size and concentration of suspended particles on the codeposition ratio of Al2O3 and the enhancement of mass transfer of copper ions were examined. Particularly, new experimental method for the measurement of the codeposition ratio was suggested and also the characteristics of the composite coating layer were measured by Rutherford Backscattering Spectrometry. Mass transfer of suspended particles system were increased up to 40% more than those of without suspended particles system. Optimum conditions of current density, hydrodynamics of RDE, and particles concentration showing maximum codeposition ratio were appeared in our experimental ranges. It was shown that the suspended inert particles were codeposited mainly near the surface of the composite coating layer.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.7-12
• /
• 2013

Ni-CNT(Carbon Nanotube) composite coatings is were formed by electrodeposition and their physical properties were investigated with variations of CNT content(1, 3, 6. 9 g/L) in the electrolyte solution, while the current density and electroplating time were fixed respectively at $6A/dm^2$ and 90 min.. With increasing CNT content from 1 to 9 g/L, incorporated CNTs into the composite coating were limited from 4.65 wt.% to 7.38 wt.%. Microhardness and contact angle values were increased with increasing CNT content of upto 3 g/L. With increasing the CNT content further, physical properties were degraded due to agglomeration, poor adhesion of CNTs to Ni matrix and thus rough surfaces. Optimum electroplating conditions were found to be the CNT content of 3 g/L, current density of 6 A/dm2 and electroplating time of 90 min.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.335-338
• /
• 2000

Carbon is an attractive candidate for use in eletrochemical supercapacitors that depend on charge storage in the electrode/electrolyte international double layer. Property of an electrical double layer capacitor depend both on the technique used to prepare the electrode and on the current collector structure. The study is to research that V$_2$O$_{5}$-flyash-AC composite electrode for supercapacitor. The discharge capacitance of V$_2$O$_{5}$-flyash-AC(70wt%) in 1st and 50th cycle was 18.6F/g and 15.13F/g at current density of 0.5mA/cm$^2$. The discharge process of V$_2$O$_{5}$-flyash (3 : 97)-AC composite electrode is larger than that others.thers.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 춘계 학술발표강연 및 논문개요집
• /
• pp.43-43
• /
• 2002

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2001년도 춘계총회 및 학술발표회
• /
• pp.41-41
• /
• 2001

• 한국막학회:학술대회논문집
• /
• 한국막학회 2005년도 추계 총회 및 학술발표회
• /
• pp.204-207
• /
• 2005

• 한국재료학회지
• /
• 제31권7호
• /
• pp.375-381
• /
• 2021

Chitosan powder is synthesized by a deasetylation process of chitin, obtained from processing of dried shrimp shell powder. Subsequently, chitosan (CS) membranes filled by montmorillonite (MMT) particles and phosphotungstic acid are prepared, and characterized by FT-IR and SEM. The morphology, obtained by SEM for the composite membrane, showed that MMT filler is successfully incorporated and relatively well dispersed in the chitosan polymer matrix. Water and methanol uptake for the CS/MMT composite membranes decrease with increasing MMT loadings, but IEC value increases. In all prepared CS/MMT composite membranes, the CS membrane filled by 5 wt% MMT particles exhibits the best proton conductivity, while that with 10 wt% MMT loading exhibits the lowest methanol permeability; these values are 2.67 mS·cm^-1 and 3.40 × 10^-7 cm²·s^-1, respectively. The best membrane selectivity is shown in the CS/MMT10 composite membrane; this shows that 10 wt% filled MMT is the optimum loading to improve the performance of the chitosan composite membrane. These characteristics make the developed chitosan composite membranes a promising electrolyte for direct methanol fuel cell (DMFC) application.