• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.4
• /
• pp.82-90
• /
• 2009

It is very important to utilize effectively fibrous waste paper in terms of cost savings, environmental effects, and governmental policies. The quality of final products and runnability of papermaking process are primarily affected by constitutions of fibrous raw materials. In specific, board grade paper depends directly on compositions of waste paper bales. At present, the raw materials of board grade paper are mainly derived from lots kinds of wastepaper. Some papermaking countries, like EU, USA and Japan have advanced classification and management systems of recycled fiber, but Korea has not yet organized systematically. In this study, evaluation of wastepaper bale compositions and their fiber properties were carried out for effective utilization of fibrous raw materials for board grade paper production. 3 kinds of wastepaper bales were classified to fibrous or non-fibrous materials. In case of fibrous materials, KOCC, kraft sack paper and white duplex board matters were main component in total weight basis, and in case of non-fibrous materials, vinyl, plastic and cloth matters were main component, in turns. 3 representative kinds of waste paper were disintegrated and classified, and then prepared to handsheet for evaluation of recycled fiber property. Consequently, fines and ash content of waste paper, isolated from KOCC and white duplex board were higher than that of kraft sack paper. pH values of all kinds of waste fibers were neutral or weak alkaline.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.2
• /
• pp.489-494
• /
• 2013

An improved method for the preparation of monomethine cyanine dyes with quinoline nucleus by one-pot three-component using 1-methyl-2-quinolinethione, quaternized 2- or 4-methylheterocyclic compounds and methyl p-toluenesulfonate as starting materials was described. Compared with the traditional methods, the new synthetic method reduced the reaction steps, shortened the reaction time, avoided the separation and purification of the intermediate and reduced cost. The dyes absorbed in the region 478.0-563.0 nm and had molar extinction coefficients of $1.3{\times}10^4-9.4 {\times}10^4L\;mol^{-1}\;cm^{-1}$. Their fluorescence maxima and Stokes shifts were in the range of 525.2-594.4 nm and 16.2-80.6 nm in different solvents, respectively. From the spectral properties of the dyes in different solvents, it could be found that the ${\lambda}_{max}$ of the dyes were shorter in protonic solvents, and showed hypsochromic shifts with the increase of polarity of the solvents.

• Korean Journal of Materials Research
• /
• v.12 no.7
• /
• pp.528-532
• /
• 2002

Anodic $TiO_2$film on Ti substrate was fabricated at 180V in sulfuric acid solutions containing phosphoric acid and hydrogen peroxide. Effects of the anodizing conditions on the morphology of the oxide layers, and chemical states of the component elements of the layers were studied primarily using SEM, XRD, AFM, and XPS. The pores in the oxide layer was not uniform in size, shape, and growth direction particularly near the interface between the substrate and the oxide layer, compared with those of the surface layer. The formation of irregular type of pores seemed to be attributed to spark discharge phenomena which heavily occurred during increasing the anodic voltage. The pore diameter and the cell size increased, and the number of cells per unit area decreased with the increasing time. From the XPS results, it was shown that component elements of the electrolytes, P and S, existed in the chemical states of $PO_4^{-3}$ , $P_2$$O_{5}$, $SO_4^{-2}$ , $SO_3^{-2}$ , P, S, etc., which were penetrated from the electrolytes into the oxide layer during anodization.

• Korean Journal of Materials Research
• /
• v.32 no.3
• /
• pp.168-179
• /
• 2022

Microbiologically Influenced Corrosion (MIC) occurring in underground buried pipes of API 5L X65 steel was investigated. MIC is a corrosion phenomenon caused by microorganisms in soil; it affects steel materials in wet atmosphere. The microstructure and mechanical properties resulting from MIC were analyzed by OM, SEM/EDS, and mapping. Corrosion of pipe cross section was composed of ① surface film, ② iron oxide, and ③ surface/internal microbial corrosive by-product similar to surface corrosion pattern. The surface film is an area where concentrations of C/O components are on average 65 %/16 %; the main components of Fe Oxide were measured and found to be 48Fe-42O. The MIC area is divided into surface and inner areas, where high concentrations of N of 6 %/5 % are detected, respectively, in addition to the C/O component. The high concentration of C/O components observed on pipe surfaces and cross sections is considered to be MIC due to the various bacteria present. It is assumed that this is related to the heat-shrinkable sheet, which is a corrosion-resistant coating layer that becomes the MIC by-product component. The MIC generated on the pipe surface and cross section is inferred to have a high concentration of N components. High concentrations of N components occur frequently on surface and inner regions; these regions were investigated and Na/Mg/Ca basic substances were found to have accumulated as well. Therefore, it is presumed that the corrosion of buried pipes is due to the MIC of the NRB (nitrate reducing bacteria) reaction in the soil.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.5-5
• /
• 2011

The research and development of hybrid electric vehicle (HEV), plug-in hybrid electric vehicle (PHEV) and electric vehicle (EV) are intensified due to the energy crisis and environmental concerns. In order to meet the challenging requirements of powering HEV, PHEV and EV, the current lithium battery technology needs to be significantly improved in terms of the cost, safety, power and energy density, as well as the calendar and cycle life. One new technology being developed is the utilization of composite cathode by mixing two different types of insertion compounds [e.g., spinel $LiMn_2O_4$ and layered $LiMO_2$ (M=Ni, Co, and Mn)]. Recently, some studies on mixing two different types of cathode materials to make a composite cathode have been reported, which were aimed at reducing cost and improving self-discharge. Numata et al. reported that when stored in a sealed can together with electrolyte at $80^{\circ}C$ for 10 days, the concentrations of both HF and $Mn^{2+}$ were lower in the can containing $LiMn_2O_4$ blended with $LiNi_{0.8}Co_{0.2}O_2$ than that containing $LiMn_2O_4$ only. That reports clearly showed that this blending technique can prevent the decline in capacity caused by cycling or storage at elevated temperatures. However, not much work has been reported on the charge-discharge characteristics and related structural phase transitions for these composite cathodes. In this presentation, we will report our in situ x-ray diffraction studies on this mixed composite cathode material during charge-discharge cycling. The mixed cathodes were incorporated into in situ XRD cells with a Li foil anode, a Celgard separator, and a 1M $LiPF_6$ electrolyte in a 1 : 1 EC : DMC solvent (LP 30 from EM Industries, Inc.). For in situ XRD cell, Mylar windows were used as has been described in detail elsewhere. All of these in situ XRD spectra were collected on beam line X18A at National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory using two different detectors. One is a conventional scintillation detector with data collection at 0.02 degree in two theta angle for each step. The other is a wide angle position sensitive detector (PSD). The wavelengths used were 1.1950 ${\AA}$ for the scintillation detector and 0.9999 A for the PSD. The newly installed PSD at beam line X18A of NSLS can collect XRD patterns as short as a few minutes covering $90^{\circ}$ of two theta angles simultaneously with good signal to noise ratio. It significantly reduced the data collection time for each scan, giving us a great advantage in studying the phase transition in real time. The two theta angles of all the XRD spectra presented in this paper have been recalculated and converted to corresponding angles for ${\lambda}=1.54\;{\AA}$, which is the wavelength of conventional x-ray tube source with Cu-$k{\alpha}$ radiation, for easy comparison with data in other literatures. The structural changes of the composite cathode made by mixing spinel $LiMn_2O_4$ and layered $Li-Ni_{1/3}Co_{1/3}Mn_{1/3}O_2$ in 1 : 1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ~5.2 V vs. $Li/Li^+$, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component only. When the cell voltage reaches at ~4.0 V vs. $Li/Li^+$, lithium extraction from the spinel $LiMn_2O_4$ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of $LiMn_2O_4$. When the voltage passed 4.3 V, the major structural changes are from the $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component, while the $LiMn_2O_4$ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel $LiMn_2O_4$ component, with much less changes in the layered $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research. More detailed discussion will be presented at the meeting.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.3
• /
• pp.215-222
• /
• 2022

Artificial neuromorphic devices are considered the key component in realizing energy-efficient and brain-inspired computing systems. For the artificial neuromorphic devices, various material candidates and device architectures have been reported, including two-dimensional materials, metal-oxide semiconductors, organic semiconductors, and halide perovskite materials. In addition to conventional electrical neuromorphic devices, optoelectronic neuromorphic devices, which operate under a light stimulus, have received significant interest due to their potential advantages such as low power consumption, parallel processing, and high bandwidth. This article reviews the recent progress in optoelectronic neuromorphic devices using various active materials such as two-dimensional materials, metal-oxide semiconductors, organic semiconductors, and halide perovskites

• Journal of Ginseng Research
• /
• v.35 no.1
• /
• pp.31-38
• /
• 2011

In order to distinguish the cultivation area of Panax ginseng, principal component analysis (PCA) using quantitative and qualitative data acquired from HPLC was carried out. A new HPLC method coupled with evaporative light scattering detection (HPLC-ELSD) was developed for the simultaneous quantification of ten major ginsenosides, namely $Rh_1$, $Rg_2$, $Rg_3$, $Rg_1$, Rf, Re, Rd, $Rb_2$, Rc, and $Rb_1$ in the root of P. ginseng C. A. Meyer. Simultaneous separations of these ten ginsenosides were achieved on a carbohydrate analytical column. The mobile phase consisted of acetonitrile-water-isopropanol, and acetonitrile-water-isopropanol using a gradient elution. Distinct differences in qualitative and quantitative characteristics for ginsenosides were found between the ginseng roots produced in two different Korean cultivation areas, Ganghwa and Punggi. The ginsenoside profiles obtained via HPLC analysis were subjected to PCA. PCA score plots using two principal components (PCs) showed good separation for the ginseng roots cultivated in Ganghwa and Punggi. PC1 influenced the separation, capturing 43.6% of the variance, while PC2 affected differentiation, explaining 18.0% of the variance. The highest contribution components were ginsenoside $Rg_3$ for PC1 and ginsenoside Rf for PC2. Particularly, the PCA score plot for the small ginseng roots of six-year old, each of which was light than 147 g fresh weight, showed more distinct discrimination. PC1 influenced the separation between different sample sets, capturing 51.8% of the variance, while PC2 affected differentiation, also explaining 28.0% of the variance. The highest contribution component was ginsenoside Rf for PC1 and ginsenoside $Rg_2$ for PC2. In conclusion, the HPLC-ELSD method using a carbohydrate column allowed for the simultaneous quantification of ten major ginsenosides, and PCA analysis of the ginsenoside peaks shown on the HPLC chromatogram would be a very acceptable strategy for discrimination of the cultivation area of ginseng roots.

• Journal of the Korean Society of Industry Convergence
• /
• v.5 no.1
• /
• pp.27-32
• /
• 2002

In this study, estimate of Mechanical Properties depending on Injected direction in Polymer for Automobile Application. The used materials is polyamid(nylon6), polypropylene(PP) of a simple component and its mixed, reinforced glass fiber(15%) in polyamid. One side direction of a simple component is highest strength and the two sides direction of multicomponent appear lowest strength. This is caused by effects of weldline, imperfect fusion and impregnation of multicomponent. To improve mechanical properties, it is necessary to minimize of weldline, compatibility, perfect fusion and impregnation in multicomponent polymer.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.297-301
• /
• 2004

The optimum design against contact crack initiation is investigated to find major parameters in designing desirable surface-coated asymmetric layered components. Hard ceramic coated soft materials with various elastic modulus mismatch are prepared for the analysis. Spherical indentation is conducted for producing contact cracks from the surface or interface between the coating and the substrate layer. A finite element analysis of the stress fields in the loaded layer components enables a direct correlation between the damage patterns and the stress distributions. Implications concerning the design of asymmetric layered components indicate that the coating thickness and the elastic modulus mismatch are important parameters for designing layered component to prevent the initiation of contact cracks.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.368-374
• /
• 2015

Hydroforming of a non-axisymmetric thin-walled tubular component with variable cross sections was analyzed. In order to solve the sealing problem which occurred due to the thin and non-axisymmetric shape, the use of a lead patch on the punch, which had been successful in hydroforming of thin tubes, was evaluated. A lead patch was attached to the punch to solve the sealing problem, which was caused by the stress gradient in the non-axisymmetric shape. FEM and experiments were also performed to analyze these sealing problems associated with the punch shape and non-axisymmetric shape. Finally, the lead patch was attached at tube surface where intensive local strain concentration would occur to enhance the hydroformability. These methods were successfully used to fabricate non-axisymmetric thin-walled tubular component with variable cross sections that had previously failed during traditional hydroforming.