• Journal of Dental Rehabilitation and Applied Science
• /
• v.17 no.2
• /
• pp.113-123
• /
• 2001

The success of complete denture prosthesis is to satisfy three basic requirements for the edentulous patient : maximum comfort, efficiency, and esthetic appearance. This can be achieved only if the dentures are both stable and retentive. When the residual alveolar ridge has resorbed significantly, stability and retention are more dependent on the correct position of the teeth and external surfaces of the denture. The stability and retention of the denture can be improved by locating the denture in the neutral zone and reproducing exact mandibular border movement for balanced occlusion. The neutral zone philosophy is based upon the concept that there exists a specific area where the musculature function will not unseat the denture in the mouth. In here, forces generated by the tongue are neutralized by the forces generated by the lips and cheeks. One of the simplest methods for recording border movements in three dimensions is to make stereographic record of condylar movement. Stereographs are made in the mouth during mandibular movement with intraoral clutches and central bearing point, and used in dictating the condylar movement on the articulator later by generating the condylar paths in doughy acrylic resin. Its procedure is simpler and more convenient than that of Pantograph. In this clinical report, we introduce the concept of neutral zone and stereograph in complete denture fabrication.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.4
• /
• pp.346-351
• /
• 2014

Suction dentures enhance retention and support by forming negative pressure temporarily at the internal surface of denture base at times of swallowing and chewing because the areas surrounding the denture flanges are sealed by mobile mucosa. In this case, an 81-year-old male visited for new dentures. Considering the high expectations for retention and masticatory efficiency of dentures, fabricating complete dentures with suction dentures was planned. Preliminary impression was taken without applying pressure on retromolar pad area and diagnostic cast was fabricated. Afterwards, individual tray was made and final impression was taken, at the same time, gothic arch tracing was done to acquire centric relation and vertical dimension. Then, anatomic teeth were placed on maxilla and non-anatomic teeth were placed on mandible forming lingualized occlusion. Consequently, restoring a complete edentulous patient with complete dentures using mandibular suction denture resulted in recovering satisfying retention and function.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.2
• /
• pp.145-152
• /
• 2020

It is essential to record maxillomandibular relationship accurately for the harmony of esthetic and function in complete denture. Gothic arch tracing visually demonstrates the movement of the mandible, and is useful to establish accurate and reproducible centric relation. Proper retention and stability of complete denture in patients with severe alveolar bone resorption is difficult to attain. In such case, the closed mouth impression technique might be recommended. The denture border and impression are determined by patient's physiologic movement in the closed mouth impression technique. And, denture peripheral border is entirely closed with oral mucous membrane. This report presents satisfactory complete denture restoration using closed mouth impression technique and gothic arch tracing in patients with mandibular condyle fracture and severe absorption of mandibular alveolar ridge.

• Journal of Technologic Dentistry
• /
• v.39 no.1
• /
• pp.25-33
• /
• 2017

Purpose: The aim of this study was to evaluate accuracy of glass fiber mesh complete denture of before and after curing. Methods: Edentulous model was selected as the master model. Ten study models were made by Type IV stone. Wax complete dentures were produced by the denture base and artificial teeth. CD and GD groups were measured six measurement distance before curing. The wax complete denture was investment after measurement is completed. Using a heat polymerization resin was injected resin. After injecting the resin it was curing. A complete denture was re-measured after curing. The measured data was verified by paired t-test. Results: Overall CD group was larger the value of the measured length. In the CD group, A-D point was larger. The smallest point was the B-D point. However, there was no statistically significant difference only C-D point(p>0.05). In the GD group, A-B point was larger. but B-D point was the smallest. A-D and B-C statistically points showed significant differences(p<0.05). Conclusion: Glass fiber mesh resin complete denture can be clinically applied to the edentulous patient.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.4
• /
• pp.426-433
• /
• 2013

When restoring edentulous patients with lower complete denture, the smaller supportive and retentive area of mandible can lead to poor support and stability, denture dislodgement and pain resulting discomfort. In this situation, implant prosthesis can improve esthetics, stability and occlusal force. Whereas, patients with a upper complete denture can adjust more easier because of palate. Therefore, it is suggested to rehabilitate fully edentulous patients with lower implant-supported, upper complete denture as one of the treatment options. So, we are going to report the case and literature review about how the lower implant prosthesis opposing to upper complete denture affects the bone resorption of maxillary residual ridge.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.4
• /
• pp.296-303
• /
• 2016

PURPOSE. The aim of this study was to evaluate whether there is any typical deformation pattern existing in complete denture when it was dried by using the 3D scanner and surface matching program. MATERIALS AND METHODS. A total of 28 denture bases were fabricated with heat curing acrylic resin (each 14 upper and lower denture bases), and 14 denture bases (each 7 upper and lower denture bases) were stored in the water bottle (water stored), and another 14 denture bases were stored in the air (dry stored). Each specimen was scanned at $1^{st}$ day after deflasking, $14^{th}$ day after deflasking, and $28^{th}$ day after deflasking, and digitalized. Three dimensional deformation patterns were acquired by comparison of the data within storage group using surface matching program. For evaluating differences between groups, these data were compared statisticallyusing Kruskal Wallis and Mann Whitney-U test (${\alpha}$=.05). RESULTS. When evaluating 3D deformation of denture base, obvious deformations were not found in maxillary and mandibular water storage group. However, in dry stored group, typical deformation pattern was detected as storage time passes. It occurred mostly in first two weeks. Major deformations were found in the bilateral posterior area in both maxillary and mandibular group. In maxillary dry stored group, a statistical significance was found. CONCLUSION. It was proved that in both upper and lower denture bases, dry storage caused more dimensional deformation than water storage with typical pattern.

• The Journal of Advanced Prosthodontics
• /
• v.4 no.2
• /
• pp.97-102
• /
• 2012

Study was conducted to determine and assess the effect of different type of denture adhesives on the incisal bite force of complete denture wearers until the dislodgement of upper denture, using pressure transducer. MATERIALS AND METHODS. 30 patients out of 100 were included in the study. Based on the Kapur's method of scoring denture retention and stability, these patients were divided into 3 groups-Group A - Clinically good dentures; Group B - Clinically fair dentures; and Group C - Clinically poor dentures. A custom made occlusal force meter was constructed based on the load cell type of pressure transducers. Different adhesives (powder, paste and adhesive strips) were used in the study. Complete denture wearers were asked to bite on the load cell and the readings of incisal bite force were recorded. The readings of incisal bite force were subjected to statistical analysis using Repeated measures ANOVA followed by post-hoc bonferroni test. RESULTS. The result suggests that denture adhesives improved the incisal bite force of complete denture wearers significantly The incisal bite force (in kg) in Group A without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 2.48 (${\pm}0.16$), 3.43 (${\pm}0.11$), 6.01 (${\pm}0.11$), 3.22 (${\pm}0.09$) respectively. The incisal bite force (in kg) in Group B without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 1.87 (${\pm}0.18$), 3.35 (${\pm}0.14$), 5.34 (${\pm}0.18$), 3.21 (${\pm}0.12$) respectively. The incisal bite force (in kg) in Group C without using adhesives, with powder adhesive, with paste adhesive and with adhesive strips was found to be 1.00 (${\pm}0.17$), 3.07 (${\pm}0.14$), 4.37 (${\pm}0.26$), 2.99 (${\pm}0.14$) respectively. CONCLUSION. Within the limitations of the study, it was concluded that the use of denture adhesive was found to be significantly effective in improving the incisal bite force of complete dentures until the dislodgement of upper denture. Fittydent paste adhesive was found to be more effective than the powder and strips adhesives. The improvement in incisal bite force was found to be higher in Group C in comparison to that of Group A and Group B.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.4
• /
• pp.338-345
• /
• 2014

Fabrication of complete denture by Jiro Abe's method was introduced that enhance the retention and stability of denture by sealing around the denture border with mucous membrane to make negative pressure at the inner surface of denture base when swallowing or occlusion. In this case, taking impression and fabricating complete denture by the Jiro Abe's method for an edentulous patient with severe mandibular alveolar bone resorption allowed us to obtain clinically enhance stability of denture and improve satisfaction of patient.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.4
• /
• pp.515-525
• /
• 1994

Impression taking is a very important procedure in complete denture fabrication for reproduction of the tissue surface from which obtain retention and support of denture base. Therefore, we can not construct retentive denture without precise impression taking. Retention in complete denture can be obtained by the closest contact between denture base and underlying tissue, maximum coverage and proper displacement of the border tissue for peripheral sealing. Therefore, it is very important to take impression of the border tissue displaced properly. Nowadays, impression of the border tissue is mainly taken by the border molding techniques by means of manual muscle trimming, but due to various muscle trimming methods as clinicians, it is difficult to select proper method. This technique is also bodersome to do and time-consuming procedure. Retention is also likely reduced, because of the recording excessive muscle movement than actural physiological border tissue movement. Therefore, the impression technique that records actual physiologic functional muscle movement is helpful to increase denture retention and easy to do. We named this technique a functional border molding technique. This technique is originally introduced by D. J. Neill and R. I. Nairn in 1968. We tried to fabricate complete denture by the impression by means of functional border molding technique for better retention and the convenience, and obtained good results.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.4
• /
• pp.364-369
• /
• 2016

Purpose: The aim of this study was to compare denture wearer's evaluation and clinician's technical rating for complete denture used on edentulous patients. Materials and methods: Total 43 edentulous patients who had complete denture fabricated more than one year ago were recalled. The questionnaire based on the various literatures was modified and applied to patients for subjective assessments. Functional aspects related to retention, stability, occlusion and denture condition were included in operator's evaluation. In addition, correlations were evaluated between patient's subjective and operator's objective assessments. Friedman test and Cohen's Kappa value were used for statistical analysis. Results: It was found that denture wearers' evaluations were slightly or fairly agree to clinician's rating for complete denture. More differences were found in maxillary denture than mandibular denture and moderate difference was found in esthetic, occlusion aspects. Conclusion: There were slightly or fairly agreement between subjective and objective evaluations.