• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.443-446
• /
• 2003

This paper implement Remote Meter Reading System which is used Bluetooth and SMS in CDMA. This System propose system which tan detect a total amount of gas, electricity or water without a meterman, at home BlueTooth is a close range wireless communication technology which uses a wireless frequency 2.4GHz and has a high trust and self error correction technology according to a low power consumption quality and a high-speed frequency hopping. This makes get a high trust concerning a data transmission than an existing modem. In addition, though wireless modem is restricted by a minimal of a wireless terminal, it will be possible to coincide with the function of the portable with the low power consumption quality by using Bluetooth. And as the system on a chip of module progresses, the possibility of the small size is present. Nowadays, SMS Protocol in CDMA for have a network function based on PPP in CDMA Phone. The proposed Remote Meter Reading System to get more nobility, efficiency, and have good function. SMS Protocol in CDMA have profits which is low power, low cost, and low microwave output.

• Journal of Sensor Science and Technology
• /
• v.17 no.2
• /
• pp.133-142
• /
• 2008

Respiration is induced by muscular contraction of the chest and abdomen, resulting in the abdominal volume change. Thus, continuous measurement of the abdominal dimension enables to monitor breathing activity. Conductive rubber cord has been previously introduced and tested to develop wearable application for respiratory measurements. The present study implemented wireless wearable respiratory monitoring system with the conductive rubber cord in the patient's pants. Signal extraction circuitry was developed to obtain the abdominal circumference changes reflecting the lung volume variation caused by respiratory activity. Wireless transmission was followed based on the zigbee communication protocol in a size of 65mm${\times}$105mm easily put in pocket. Successful wireless monitoring of respiration was performed in that breathing frequency was accurately estimated as well as different breathing patterns were easily recognized from the abdominal signal. $CO_2$ inhalation experiment was additionally performed in purpose of quantitative estimation of tidal volume. Air mixed with $0{\sim}5%\;CO_2$was inhaled by 4 normal males and the respiratory air flow rate, abdominal dimension change, and end tidal $CO_2$ concentration were simultaneously measured in steady state. $CO_2$ inhalation increased the tidal volume in normal physiological state with a correlation coefficient of 0.90 between the tidal volume and the end tidal $CO_2$ concentration. The tidal volume estimated from the abdominal signal linearly correlated with the accurate tidal volume measured by pneumotachometer with a correlation coefficient of 0.88 with mean relative error of approximately 8%. Therefore, the tidal volume was accurately estimated by measuring the abdominal dimension change.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.16-21
• /
• 2007

Various perturbations by the sun, the moon and the earth itself cause a continuous change in nominal position of a geostationary satellite. In order to maintain the satellite within a required window, north-south station keeping for controlling inclination and right ascension of ascending node, and east-west station keeping for controlling eccentricity and longitude are required. In this paper, station keeping maneuver simulation for Communication, Ocean and Meteorological Satellite (COMS) was performed using COMS Flight Dynamics Software(FDS) and the results were analyzed. COMS performs weekly based east-west/north-south station keeping to maintain satellite within ${\pm}0.05^{\circ}$ at the nominal longitude of $128.2^{\circ}E$. In addition, COMS performs wheel off-loading maneuver twice a day to eliminate attitude error caused by one-solar wing in the south panel of the satellite. In this paper, station keeping maneuver considering wheel off-loading maneuver was performed and the results showed that COMS can be maintained well within ${\pm}0.05^{\circ}$ window using COMS FDS.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.523-529
• /
• 2017

In this paper, we propose an efficient sphere decoding scheme that reduces computational complexity by combining receive and transmit ordering techniques in generalized spatial modulation systems, where the indexes of activated transmit antennas as well as the transmit symbols are exploited to transfer information to the receiver. In this scheme, the receive signals are optimally ordered so that the calculation for a candidate solution outside the sphere is terminated early to lower the computational complexity. In addition, the transmit ordering technique is applied to first search for candidate symbols and activated antennas having higher probabilities to further reduce the computational complexity. Simulation results show that the proposed doubly ordered sphere decoding scheme provides the same bit error rate performance with the conventional sphere decoding method and the sphere decoder employing only the receive ordering technique while it requires lower computational complexity.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.204-216
• /
• 2010

Since Sensor nodes around a fixed sink have huge concentrated network traffic, the battery consumption of them is increased extremely. Therefore the lifetime of sensor networks is limited because of huge battery consumption. To address this problem, a mobile sink has been studied for load distribution among sensor nodes. Since a mobile sink changes its location in sensor networks continuously, the mobile sink has time limits to communicate with each sensor node and unstable signal strength from each sensor node. Therefore, a fair and stable data collection method between a mobile sink and sensor nodes is necessary in this environment. When some sensor nodes are not able to send data to the mobile sink, a real-time application in sensor networks cannot be provided. In this paper, the new scheduling method, FQMS (Fair Queuing for Mobile Sink), is proposed for fair and stable data collection for mobile sinks in sensor networks. The FQMS guarantees balanced data collecting between sensor nodes for a mobile sink. In out experiments, the FQMS receives more packets from sensor nodes than legacy scheduling methods and provides fair data collection, because moving speed of a mobile sink, distance between a mobile sink and sensor nodes and the number of sensor nodes are considered.

• The KIPS Transactions:PartA
• /
• v.16A no.3
• /
• pp.169-180
• /
• 2009

With fixed sinks, the network stability could be improved while the network life time could be decreased by the rapid energy dissipation around the fixed sink because of the concentrated network traffic from sensor nodes to the fixed sink in wireless sensor network. To address this problem, mobile sinks, which decentralize the network traffic, has received a lot of attention from many researchers recently. Since a mobile sink has a limited period to communicate with each sensor nodes, it is necessary for a scheduling algorithm to provide the fairness of data collection from each sensor nodes. In the paper, we propose the new scheduling algorithm, ASF(Availability based Scheduling scheme for Fair data collection), for the fair data collection by a mobile in the sensor networks. The ASF takes account of the distance between each sensor nodes and the mobile sink as scheduling metric, as well as the amount of collected data from each sensor nodes. Experiment results shows that the ASF improves the fairness of data collection among the sensor nodes, comparing to existing algorithm.

• Journal of Aerospace System Engineering
• /
• v.12 no.4
• /
• pp.64-74
• /
• 2018

Small high-resolution Earth observation satellites require precise optical alignment at the submicron level. However, misalignments can occur due to the influence of external factors during the launch and operation despite the sufficient alignment processes that take place before the launch. Thus, satellites need to realign their optical elements in orbit in what is known as a refocusing process to compensate for any misalignments. Refocusing algorithms developed for satellites have only considered de-space, which is the most sensitive factor with respect to image quality. However, the existing algorithms can cause correction error when inner and external forces generate tilt amount in an optical system. The present work suggests an improved online refocusing algorithm by considering the tilting effect for application in the case of a de-spaced and tilted optical system. In addition, the algorithm is considered to be efficient in terms of time and cost because it is designed to be used as an online method that does not require ground communication.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.3
• /
• pp.50-61
• /
• 2011

The Infrared touch method is generally used for a mid and large-size touch screen. But this method has several problems, such as difficulty with installation of a touch-object recognition device, limited application and coordinate error in multi-point touch system. Since we can take advantages of both color and local information when we use general cameras for a touch screen, a touch screen using general camera is more efficient than infrared one. It also has an advantage of easy installation of a touch-object device. However, it did not much appeal in a market because of several problems, such as color sensitivity, illumination and reflected light. In this paper, we study a method for a touch screen using a general camera and image processing method to recognize touch objects and coordinate calculation method to single and multi-point touch screen. It has the same recognition performance as an infrared touch screen for single-point method. And it does not have ghost point problem by using distance information of touch object and camera in multi-point touch system. But recognition performances of multi-point touch screen are less than single-point. If we improve execution time, this method can replace an infrared method for a single point touch screen, according to result of experience.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.30-37
• /
• 2007

An exponentiation in $GF(2^m)$ is a basic operation for several algorithms used in cryptography, digital signal processing, error-correction code and so on. Existing hardware implementations for the exponentiation operation organize by Right-to-Left method since a merit of parallel circuit. Our paper proposes a polynomial exponentiation structure with a trinomial that is organized by Left-to-Right method and that utilizes a weakly dual basis. The basic idea of our method is to decrease time delay using precomputation tables because one of two inputs in the Left-to-Right method is fixed. Since $T_{sqr}$ (squarer time delay) + $T_{mul}$(multiplier time delay) of ow method is smaller than $T_{mul}$ of existing methods, our method reduces time delays of existing Left-to-Right and Right-to-Left methods by each 17%, 10% for $x^m+x+1$ (irreducible polynomial), by each 21%, 9% $x^m+x^k+1(1, by each 15%, 1% for $x^m+x^{m/2}+1$.

• Journal of the Korea Convergence Society
• /
• v.6 no.6
• /
• pp.285-291
• /
• 2015

FTMS, TCS, ITS equipment such as high-pass highway are just a situation that does not lack traceability and passive surveillance is related to fault DB has so far consisted of an integrated operations management to maximize utilization of the facility. In addition, there is no replacement parts are replaced when a failure occurs, increasing the number of parts and repair time I have trouble growing, and becoming a service interruption whenever you replace each time. In this study, proactively manage the failure history of a highway facility ITS tries to preventive maintenance. Therefore, the error history is based on the reliability of the high-pass facilities theory to calculate the reliability of the system through a systematic statistical analysis Operational Availability. The fault number and the time the replacement period through the estimate decreases and can reduce the budget expenses by securing the spare parts quantity, establish a management plan in part by improving the quality of the system through constant preventive maintenance, quality of service at all times It may direct the non-stop operation state of the available state.