• 한국분무공학회지
• /
• 제13권2호
• /
• pp.65-72
• /
• 2008

It is recognized that alternative fuel such as dimethyl ether (DME) has better combustion polluting characteristics than diesel fuel, even though the cetane number of DME is almost the same as that of diesel. Characteristics of DME spray were observed experimentally under various ambient conditions using a constant volume chamber and a common-rail injection system. N-dodecane and LPG fuel sprays were also observed under same conditions of DME spray. Using spray images from backlight scattering and Mie scattering, characteristics of fuel sprays such as penetration and spray volume were visualized and quantitatively measured. The measurements showed that the penetration of early period decreased remarkably, because evaporation of alternative fuels became prosperous by the influence of flash boiling phenomenon under the condition of the low temperature and pressure compared with n-dodecane. The penetration of DME and LPG spray received the influence of temperature more largely in comparison with low density, because the specific surface area increased by atomizing in high density.

• 한국분무공학회지
• /
• 제14권2호
• /
• pp.84-89
• /
• 2009

In this research, combustion and spray characteristics were investigated experimentally in a constant volume chamber by applying different composition rates of octane number in diesel fuel to a common-rail system. For the visualization, the experiment was carried out under different injection pressures and different cetane number. The test was done by three different types of diesel fuels, the different composition rates of cetane number in diesel fuel and HBD. In summary, this research aims to investigate the combustion characteristics in the application of fuels and compare the results with performance of conventional diesel fuel. This experimental data may provide with fundamentals of the development of diesel engines in future.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.80-89
• /
• 2004

In order to confront the increasing air pollution and the tightening emission restrictions, this research developed a diesel engine using DME, the advanced smoke-free alternative fuel. By numerical analysis, flow field, spray, and combustion phenomenon of the DME engine was presented. Using an experimental method, the configuration of the fuel supply system and operation/power performance was tested with the current plunger pump. Most emission performance, especially smoke performance was significantly improved. The possibility of conversion from the current diesel engine into the DME engine was affirmed in this research. However, it was found that the increase of engine RPM and fuel amount need to be properly adjusted through matching the characteristics of fuel and injector for further improvement.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.459-462
• /
• 2013

CRDI 시스템에서의 ECU는 센서의 정보를 분석하여 최적의 조건으로 엔진이 동작하도록 한다. 이러한 ECU의 프로그램 부분과 데이터 부분은 제작자에서만 변경할 수 있어 엔진을 진단하는 진단기의 경우 전문가가 아니면 사용하거나 내용을 이해하기가 쉽지 않다. 본 연구에서는 산업용 차량의 엔진 데이터 값을 OBD-II표준을 사용하여 입력받아 사용자 중심의 진단기를 PC 및 모바일용으로 개발하였다. 본 연구의 진단기는 운전자 중심의 진단 서비스를 제공하며, 자동차 고장진단 신호 및 센서 출력 신호를 유선시스템과 무선 시스템인 블루투스 모듈을 이용하여 실시간 통신이 제공되도록 함으로써 엔진이상으로 인한 사고의 예방이 가능하고, 최적의 조건으로 엔진이 동작하므로 과도한 배기가스 배출이나 불완전 연소가스 배출과 같은 대기환경오염을 예방할 수 있어 최근 대두되고 있는 에코산업에도 이바지 할 수 있을 것이다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2013년도 제46회 KOSCO SYMPOSIUM 초록집
• /
• pp.37-40
• /
• 2013

Hydrogen-dimethy ether (DME) and hydrogen-diesel compression ignition engine combustion were investigated and compared each other in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME and diesel were injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME and diesel inejction timing was varied to find the optimum CI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. Fuel consumption, heat release rate, and exhaust emissions were measured to analyze each combustion characteristics of each ignition promoter. Fuel consumption was decreased when diesel was used as an ignition promoter. This is due to the lower volatility of diesel which created more stratified charge than DME.

• 한국분무공학회지
• /
• 제24권2호
• /
• pp.66-72
• /
• 2019

Diesel vehicles suffer from poor starting and running problems at cold temperatures. Diesel vehicles have the characteristic that CO and PM are reduced or similarly discharged when going from low temperature to high temperature. In this study, a bypass type piezo injector for electronic control based common rail injection system was used. Numerical analysis using injector drive analysis model was performed to analyze injector drive and internal fuel flow characteristics according to fuel temperature change. The results show that the rate of density change due to the fuel temperature is proportional, and that the effect of the kinematic viscosity is relatively large between $-20^{\circ}C$ and $0^{\circ}C$. Comparing the results of temperature condition at $0^{\circ}C$ and $20^{\circ}C$, it is considered that the viscosity is more correlated with the needle displacement than the pressure chamber of the delivery chamber.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2014년도 춘계학술대회
• /
• pp.458-461
• /
• 2014

CRDI 시스템에서의 ECU는 센서의 정보를 분석하여 최적의 조건으로 엔진이 동작하도록 한다. 이러한 ECU의 프로그램 부분과 데이터 부분은 제작자에서만 변경할 수 있어 엔진을 진단하는 진단기의 경우 전문가가 아니면 사용하거나 내용을 이해하기가 쉽지 않다. 본 연구에서는 산업용 차량의 엔진 데이터 값을 OBD-II 표준을 사용하여 입력받아 사용자 중심의 진단기를 PC 및 모바일용으로 개발하였다. 본 연구의 진단기는 운전자 중심의 진단 서비스를 제공하며, 자동차 고장진단 신호 및 센서 출력 신호를 유선시스템과 무선 시스템인 블루투스 모듈을 이용하여 실시간 통신이 제공되도록 함으로써 엔진이상으로 인한 사고의 예방이 가능하고, 최적의 조건으로 엔진이 동작하므로 과도한 배기가스 배출이나 불완전 연소가스 배출과 같은 대기환경오염을 예방할 수 있어 최근 대두되고 있는 에코산업에도 이바지 할 수 있을 것이다.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.156-163
• /
• 2014

Diesel engine is most suitable one for biodiesel fuel because the compression-ignition diesel engine has desirable fuel consumption due to higher thermal efficiency and in addition, the improvement of the fuel consumption also leads to a reduction of $CO_2$ emission and then it does not need to have spark-ignition system, which means that there is less charge on the technic and complexity. In this study, the spray behavior characteristics of the vegetable palm oil were analyzed by using a common-rail injection system of commercial diesel engine and the results were compared with those obtained for the diesel fuel. The injection pressures and blend ratios of palm oil and diesel(BD3, BD5, BD20, BD30, BD50, and BD100) were the main parameters. The experiments were conducted for different injection pressures: 500bar, 1000bar, 1500bar, and 1600bar by setting injection duration to $500{\mu}s$. Consequently, it was found that there is no significant difference in the macro characteristics of the spray behavior(spray penetration and spray angle) in response to change in the blend ratio of palm oil and diesel at a fixed injection pressure. In particular, all experiments showed the spray angle about $12^{\circ}{\sim}13^{\circ}$.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.29-37
• /
• 2013

Compared to gasoline engines, diesel engines with a relatively simple ignition system are more advantageous in the application of biodeisel fuel to engine. Then in this study the comparative analysis on the spray characteristics and combustion emissions characteristic between the biodiesel(soybean oil) and diesel, the fuel for commercial diesel engine, was performed with common rail injection system. Injection pressure and ratio of biodiesel blended fuel were selected as main experimental variables. Consequently, it can be found that there is no significant difference in the macro characteristics of the spray behavior(spray penetration and spray angle) in response to change in the blend ratio of soybean oil and diesel at a fixed injection pressure, in particular, soot creation in combustion emissions in the region of low pressure was greatly affected by the blend ratio of soybean oil, however, the creation in the region of high pressure was almost unaffected by the blend ratio because of promoted atomization.

• 수산해양기술연구
• /
• 제52권1호
• /
• pp.65-71
• /
• 2016

Injection rate, injection quantity and injection timing of fuel are controlled precisely by electric control in CRDI system. Particularly, injection rate being influenced with injection pressure affects to spray characteristics and fuel-air ratio, so it is a very important factor in diesel combustion. In this study, injection rates in accordance with injection pressure at a constant ambient pressure were measured with Zeuch's method. Under the same condition, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. Injection start time and injection period were practically affected with injection pressure. Also, initial injection rate, spray penetration, spray angle and breakup of high density droplets region in the spray were affected with injection pressure. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for common rail direct injection system.