• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.3
• /
• pp.353-362
• /
• 2009

A new method and equipment for measuring the zeta potential of the external surface of hollow fiber (HF) membranes is reported. An existing commercial streaming potential analyzer in conjunction with home-made test cells was used to determine the electrokinetic surface characteristics of various HF membranes. It was shown that measurements of the external surface of HF membrane using the home-made test cells designed in this study were easy and reliable. The zeta potential values were quite accurate and reproducible. By varying the physical shape of the test cells to adjust hydrodynamics inside the test cells, several upgrade versions of home-made test cells were obtained. It was shown that the zeta potential of the external surface of HF membranes was most influenced by membrane materials as well as the way of surface modification. However, the overall surface charge of tested HF membranes were much less than that of commercial polyamide thin-film-composite (TFC) reverse osmosis (RO) membranes due to the lack of surface functional groups. For the HF membranes with the same material, the effect of pore size on the zeta potential was not significant, implying the potential of accurate zeta potential measurements for various HF membranes. The results obtained in this study are expected to be useful for better understating of electrokinetic surface characteristics of the external surface of HF membranes.

• Nuclear Engineering and Technology
• /
• v.53 no.6
• /
• pp.1858-1868
• /
• 2021

Resisting an accidental impact of large commercial aircrafts is an important aspect of advanced nuclear power plant (NPP) design. Especially after the 9·11 event, some regulations were enacted, which required the design of NPPs should consider the accidental impact of large commercial aircrafts. Normal working of equipment is important for stopping reactor under an impact when an NPP is in operation. However, there is a lack of reliable analysis and research on the impact test of nuclear prototype equipment. Therefore, in order to study the response of the equipment under high acceleration impact, a centrifugal pump is selected as the research object to perform the impact test. A horizontal half-sinusoidal pulse wave was applied to the working pump. The test results show that the horizontal response of the motor and flange is greater compared to other parts, as well as the vertical response of the coupling. The stress response of the pump body support and motor support is high, hence these parts should be considered in the design of the pump. Finally, combined with the damage and stress evaluation results of the pump under different amplitudes, the ultimate impact acceleration that the pump can withstand is given.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.28 no.4
• /
• pp.12-20
• /
• 2020

The purpose of this study was to analyze the face validity of the revised EPTA (English Proficiency Test for Aviation) to see if the tests actually contribute to the enhancement of aviation safety and achieve the purpose of the assessment. In order to reach the above objectives, 103 pilot test takers were surveyed, and nine in-depth interviewees were selected and interviewed. In addition, detailed research results were derived by dividing the participants into the pilot's flight experience (31 captain pilots, 42 first officer pilots, and 30 general commercial pilots). As a result, pilot participants were generally aware that EPTA was more reasonable because the revised EPTA properly implemented the aviation situation and gave participants motivation to learn aviation English. It was also seen that first officer pilots had a higher face validity of EPTA than captain and general commercial pilots. The reason was that first officer pilots considered air traffic control job was more important than other pilots did.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.12
• /
• pp.1779-1784
• /
• 2009

Establishment of simultaneous analysis method and monitoring for individually analyzing residual eight ergosterol biosynthesis inhibitors, EBI (difenoconazole, diniconazole, fenarimol, fenbuconazole, hexaconazole, myclobutanil, nuarimol and paclobutrazol) pesticides in commercial agricultural products, were conducted. The simultaneous analysis method for the pesticides was established using a GC/MS/MS for EBI pesticides. Residual amount of those pesticides were investigated in 989 commercial agricultural products (fifteen kinds of cereal grains, vegetables, beans, nuts, fruits and mushrooms) from seven metropolitan cities and eight provinces. In EBI pesticides analysis, linearity of GC/MS/MS analysis was 0.9974-0.9992, and that of recoveries were 86-135% with relative standard deviations (RSD) <20%. The limit of quantification (LOQ) of the method ranged from 0.5 to 5.0 mg/kg for eight EBI pesticides. According to the monitoring of the EBI pesticides in commercial agricultural products, difenoconazole, fenarimol, hexaconazole showed various residual levels (total frequency of 8/989 detection, 0.8%). Paclobutrazole showed in excess levels of the MRLs (maximum residue limits) for pesticides in one chard sample by the Korea Food Code. As a result of exposure assessment on the detected 8 individual pesticides, all pesticides (difenoconazole, fenarimol, hexaconazole, paclobutrazole) were evaluated as safe level in comparison to toxicologically acceptable daily intake.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.3 no.1
• /
• pp.32-43
• /
• 1995

Ni-Ti alloy has excellent corrosion resistance, biocompatibility, shape memory effect and superelasticity, so it has been used widely in biomedical fields. But it has difficulty in casting due to its high melting temperature and oxygen affinity at high temperature. Recently it has been attempted to cast Ni-Ti alloy using new casting machine and investment. The purpose of this study was to examine the superelastic behavior of cast shape memory Ni-Ti alloy and to compare the mechanical properties of the cast shape memory alloy with those of commercial alloys for removable partial denture framework. Ni-Ti alloy(Ni 50.25%, Ti 49.75% : atomic ratio) was cast with dental argon-arc pressure casting machine and Type IV gold alloy, Co-Cr alloy, Ni-Cr alloy, pure titanium were cast as reference. Experimental cast Ni-Ti alloy was treated with heat($500{\pm}2^{\circ}C$) in muffle furnace for 1 hour. Transformation temperature range of cast Ni-Ti alloy was measured with differential scanning calorimetry. The superelastic behavior and mechanical properties of cat Ni-Ti alloy were observed and evaluated by three point bending test, ultimate tensile test, Vickers microhardness test and scanning electron microscope. The results were as follows : 1. Cast Ni-Ti alloy(Ni 50.25%, Ti 49.75% : atomic ratio) was found to have superelastic behavior. 2. Stiffness of cast Ni-Ti alloy was considerably lesser than that of commercial alloys for removable partial denture. 3. Permanent deformation was observed in commercial alloys for removable partial denture framework at three point bending test over proportional limit(1.5mm deflection), but was not nearly observed in cast Ni-Ti alloy. 4. On the mechanical properties of ultimate tensile strength, elongation and Vickers microhardness number, cast Ni-Ti alloy was similiar to Type IV gold alloy, Co-Cr alloy, Ni-Cr alloy and pure titanium. With these results, cast Ni-Ti alloy had superelastic behavior and low stiffness. Therefore, it is suggested that cast Ni-Ti alloy may be applicated to base metal alloy for removable partial denture framework.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.1
• /
• pp.27-32
• /
• 2000

Various release test methods have been applied for the evaluation of nicotine release in vitro from commercial patches. However, whether and how the release data reflect the permeation of nicotine across the skin, is not fully elucidated. To predict in vivo bioavailability from in vitro release tests, correlation between in vitro release and in vitro skin permeation was assessed in the present study. Release of nicotine from three commercial patches was measured for 24 hours under nine experimental conditions which were classified depending on the apparatus (i.e., paddle over disk, cylinder and reciprocating holder) and dissolution media (i.e., phosphate buffer pH 7.4, water and the 1 % phosphoric acid pH 1.5). In vitro permeation of nicotine from the patches across the human cadaver skin was also measured using a diffusion cell. The release of nicotine was better explained by the Higuchi's equation rather than by the first order rate equation. Correlation between the release rate and the in vitro skin permeation differed among the patches. However, in general, the cylinder method, in which water is used as a dissolution medium, showed the highest correlation among the nine release test conditions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.44 no.3
• /
• pp.427-440
• /
• 2020

This study developed a vest prototype capable of monitoring body temperature using textile electrodes to prevent the sudden death of babies as well as to determine the quality of developed products by evaluating usability with commercial products. Based on the results of the 7th Size Korea Project, a basic pattern for a vest prototype was drafted by applying the average size of two-year-old Korean babies. Two prototypes were the detachable (VEST I) and integrated textile electrodes vest type (VEST II), which followed the same design. The materials were 100% cotton single jersey (SJ) and double jersey (DJ). Six experts evaluated the usability of the developed vests (VEST I & VEST II) and commercial product (VEST M). The single-layer woven textile electrode appeared to have a slightly higher conductivity than the double-layer one. There was no statistical difference in the body temperature sensing function between VEST I and VEST II. Finally, the superiority of the VEST I was verified through a comparison with commercial products (VEST M). The usability test suggested that a wearable smart clothing system of the integrated conductive textile could be further commercialized for bio-monitor applications in Ubiquitous-health care.

• 연구논문집
• /
• s.29
• /
• pp.57-67
• /
• 1999

This paper presents the status quo of the development of a piecewise bendable switch system for the urban transit MagLev. MagLev system as well as railroad requires switch systems to reach its destination. Requirements of the switch system for commercial lines are high speed operation satisfying about 2-3 minute headway and system reliability, etc. Parallel moving type switch system was installed on the test track of urban transit MagLev in KIMM. In this system, switch operation from one position to another can be done in about 90 seconds. Therefore, we concluded that this system can not satisfy the headway for the commercial lines. We decided to develop a high speed piecewise bendable switch system in which switching can be done in 20 seconds. Designed switch system is very complicated in view of operating mechanism. It consists of 11 segmented girder beams driven by hydraulic cylinders. To gain the idea of a piecewise bendable switch system, we manufactured and tested a 1/5 scale switch model. We are going to construct a full scale piecewise bendable switch system next year.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.2
• /
• pp.68-74
• /
• 2015

Time domain response analysis for vibro-impact nonlinear behavior of multi-span tube with loose supports was performed using commercial FEA code and user subroutine. Support geometry of multi-span tube with a finite gap is realistically modeled by analytical rigid surface. Model of hydrodynamic force is based on the Qusai-steady model which accounts for the inclined angle of relative flow velocity and time delay between flow force and resulting tube motion. During tube vibration from flow loading, impact and friction at the support location is simulated using commercial FEA code with master slave contact algorithm. Analysis results has reasonable agreement with those of references and test experience. Plan of further refinement of analysis model and future test verification is briefly introduced.

• Journal of Korean Society for Quality Management
• /
• v.45 no.4
• /
• pp.933-942
• /
• 2017

Purpose: The purpose of this paper is to evaluate the performance quality of the open source DBMSs. Performance quality is defined as processing time for Join queries. Query processing time is measured and compared in the most widely used open source DBMSs and commercial DBMS. Methods: By varying the number of tuples of two relations to be joined, the average processing time(seconds) of a Join query in each DBMS was obtained experimentally. ANOVA and Tukey HSD test were used in order to compare the performance quality of DBMSs. Results: There was a significant difference between the performance qualities of the three DBMSs at all experimental levels where the number of tuples was 100, 1,000, 2,000, 10,000, and 50,000. As a result of the Tukey HSD test, two open source DBMSs (MariaDB, MySQL) were classified in the same group only at the tuple level of 100. The commercial DBMS (MS-SQL Server) belonged to another group. At level of more than 1,000 tuples, all three DBMSs belonged to different groups. Conclusion: Within the open source DBMS group, MariaDB showed the better performance quality except for a small number of tuples. Thus the results show that MariaDB can be the alternative to MySQL which is currently most widely used. Between open source DBMS and commercial DBMS groups, MS-SQL Server always shows the best performance quality, but the less number of tuples, the less the difference.