• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.74-80
• /
• 1999

Work roll wear in the cold rolling of mild steel strip is strongly affected by rolling materials, rolling conditions such as roll arrangement in the cold rolling mill and lubrication. The tests were performed to find the effects of roll arrangement n the cold rolling mill on the work roll wear under the same lubricating conditions. The obtained results are as follows:If the distance of cold rolling is about 60km, the surface roughness of its was reduced by half(Ra 0.49${\mu}{\textrm}{m}$) and Pc(peak count) also was decreased to 60 ea/cm.It is easier for CC(Continuous casting) to make a slip on rolling than IC(Ingot casting). It is due to surface mirror in which first residual product appears and iron powder included Al2O3 is sticked. Because bending degree of 4Hi-rolling mill is higher than 6Hi-rolling mill, the first surface mirror was occurred to its center-point which is loaded strongly. 6Hi-rolling mill shape-controlled by intermediate roll doesn't need the initial crown to work roll. Therefore, fatigue and wear would appear a little bit.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.74-81
• /
• 1997

The purpose of this study is to develop a cold rolling oil with lubricity and mill cleanness property under the rolling conditions of high reduction ratio and high rolling speed. Six kinds of oil samples were blended. Evaluation of lubricity and anti-seizuro property of the samples were carried out with a laboratory scale rolling mill, where the contact conditions between work roll and strip are very close to actual cold rolling mill. Laboratory evaluation for dispersion, contamination, anti-oil stain property and residual carbon, etc. were carried out with several testers such as longterm circulation tester, Coulter counter and Conradson tester. A new high speed cold rolling oil with good lubricity and mill cleanness property was developed compared with the previously developed rolling oil.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1083-1086
• /
• 1996

Cold rolling mill process in steel works uses stands of rolls to flatten a strip to a desired thickness. At cold rolling mill process, precalculation determines the mill settings before a strip actually enters the mill and is done by an outdated mathematical model. A corrective neural network model is proposed to improve the accuracy of the roll force prediction. Additional variables to be fed to the network include the chemical composition of the coil, its coiling temperature and the aggregated amount of processed strips of each roll. The network was trained using a standard backpropagation with 4,944 process data collected from no.1 cold rolling mill process from March 1995 through December 1995, then was tested on the unseen 1,586 data from Jan 1996 through April 1996. The combined model reduced the prediction error by 32.8% on average.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.96-103
• /
• 2001

The quality requirements for thickness accuracy in cold rolling continue to become more stringent, particularly in response to exacting design specification from automotive customers. One of the major impacts from the tighter tolerance level is more unusable product on the head end and tail end of tandem mill coils when the mill is in transition to or from steady state rolling condition. A strip thickness control system for a tandem cold steel rolling mills is composed with blocked non-interacting controller and controllers for strip thickness and tension control of each rolling stands. An intelligent mathematical model included an elastic deformation of strip has been developed and applied to the field in order to predict the rolling force. The simulated results showed that the effect of elastic recovery should be included the model, even if the effect of elastic compression was not important.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.109-118
• /
• 2004

No.2 PCM (Pickling and tandem cold rolling mill) at Pohang works was revamped in 2003. The purpose of this project is to produce carbon and stainless steel using conventional carbon production process, rolling and annealing. This paper introduces the applied facilities and technologies of PCM which are used in production of carbon and stainless steel. To realize the main purpose of this project, POSCO have developed laser weld technology in normal carbon and special steel (stainless, high carbon and high silicon). And this report describes the method which is developed to get down the surface defect of stainless 400 series. After revamping, No.2 PCM can have competitive power in this field and can supply the special steel using carbon rolling process.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.39-39
• /
• 2000

In this paper, a decoupler of tandem cold rolling mill is designed. Before designing the decoupler, this paper improved conventional linear model by considering friction and yield stress of rolling strip. In a stand, the decoupler let an output be controlled by an input. And even if states of other stands should be changed, current stand takes no interference from those changes. In addition, with the same method, a feedforward controller is designed for an input strip thickness error. Finally, performance of controllers above is shown with nonlinear simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.220-220
• /
• 2000

In this paper, some non-interaction problems in tandem cold rolling mill are considered, which are required to control effectively a thickness of the cold .oiled strip. First, Interstand non-interactive compensate. (Interstand NIC) is designed for decoupling the interaction between stands. Next, a L2 optimization based pre-compensator is designed for decoupling the interaction between roll gap and strip tension in the stand. Finally, the effectness of the proposed decoupling methods is demonstrated via simulations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.150-157
• /
• 1999

As the customer demands thickness quality stricter, new techniques of automatic thickness control(AGC), is adopted to continuous cold rolling mills. The cold rolling mills of Pohang Works have revamped the existing conventional AGC system that control the thickness at all-stands automatically by the mass flow AGC based on the measurement of strip-speed and thickness between mill stands. The No. 2 Cold Rolling Mill be has adopted the New AGC system since Oct. 1995, and The No.1 Cold Rolling Mill since June. 1999. Thanks to the New AGC system, precise control of thickness is possible not only at constant rolling speed region, but also during line speed up and down. This report describes application techniques of the New AGC system and performance of the system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.7
• /
• pp.1030-1041
• /
• 1997

The control model in the tandem cold rolling mill consists of many mathematical theories and is used to calculate the reference values such as the roll gap and the rolling speed for good operation of rolling mill. But, the control model used presently has a problem causing inaccurate prediction of the rolling force. By the parameter identification, it was found that the main factor causing inaccurate prediction of the rolling force was incorrect modeling of the friction coefficient and the flow stress. To get rid of the erroneous factor new adaptive schemes are suggested in this work. Those are a long-time adaptation by the iterative least-square method and a short-time adaptation by the recursive weighted least-square method respectively. The new equations for the friction coefficient and the flow stress are derived by applying the suggested adaptive algorithms. Through the on-line test in an actual mill, it is proved that the rolling force predicted by the new equations is more accurate than the one by the existing equations ever used.

• Korean Journal of Metals and Materials
• /
• v.48 no.7
• /
• pp.644-650
• /
• 2010

Interstitial free (IF) steel sheets were cold rolled by the cross-roll rolling mill in which the roll axes are tilted by ${\pm}7.5^{\circ}$ away from the transverse direction of the rolled sample. After cross-roll rolling of IF steel sheets, the cold rolling and the recrystallization textures were distinguished from those observed after rolling in a normal rolling mill. The three-dimensional finite element method (FEM) simulation revealed that the operation of a large shear strain ${\varepsilon}_{23}$ during cross-roll rolling leads to the formation of a distinct cold rolling texture. During recrystallization annealing, a pronounced change in texture components was not observed, which is attributed to the lack of either selective growth or oriented nucleation during the recrystallization process. Cold cross-roll rolling led to the formation of finer recrystallized grains in IF steel sheets.