• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2254-2256
• /
• 2000

This paper presents an implantable telemetry LC resonance-type pressure sensor for the measurement of the ventricle pressure. This sensor consists of a capacitor and an inductor. This resonant circuit is magnetically coupled with an external antenna coil. The resonance frequency of the circuit decreases as the sensor capacitance is increased by the applied pressure. The inductance and the capacitance are 428nH and 0.98${\mu}F$, respectively. The resonance frequency is 245.7MHz when the differential pressure is zero. The sensitivity of the sensor is 9.477kHz/Pa.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.44-50
• /
• 2001

The largest problem in applying the elecbical partial discharge measurement method the transformer that has been operated until now is the removal of external corona noise In this thesis, a methcd was studied. to rneasme only fue partial discharge sIgnal due to the defoct in transfonrer except the external corona noise. To find out the types of partial discharge and corona noise within a transfomr, a partial discharge was made in use of a needle-plane electrodes within a model transfonner and, at the same time, an external corona noise was generated in use of a rod-sphere electrcdes in the air around the transformer. Both of a partial clischarge signal caused from an intemat defect within a transformer and an external noise were found at the rogowski coil which was located at transformer earth wire. When the external corona noise, which was separately measured in use of an antenna sensor out of transfonner, was removed from the signal measured on rogowski coil, the signal caused by partial discharge within a transformer would effectively be acquired.quired.

• Journal of Magnetics
• /
• v.19 no.2
• /
• pp.155-160
• /
• 2014

The heating produced by the absorption of radiofrequency (RF) has been considered a secondary undesirable effect during MRI procedures. In this work, we have measured the power absorbed by distilled water, glycerol and egg-albumin during NMR and non-NMR experiments. The samples are dielectric and examples of different biological materials. The samples were irradiated using the same RF pulse sequence, whilst the magnetic field strength was the variable to be changed in the experiments. The measurements show a smooth increase of the thermal power as the magnetic field grows due to the magnetoresistive effect in the copper antenna, a coil around the probe, which is directly heating the sample. However, in the cases when the magnetic field was the adequate for the NMR to take place, some anomalies in the expected thermal powers were observed: the thermal power was higher in the cases of water and glycerol, and lower in the case of albumin. An ANOVA test demonstrated that the observed differences between the measured power and the expected power are significant.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.556-560
• /
• 2012

Nanocrystalline CrN coatings were deposited by DC and ICP-assisted magnetron sputtering on Si (100) substrates. The influences of the ICP power on the microstructural and crystallographic properties of the coatings were investigated. For the generation of the ICP, radio frequency was applied using a dielectric-encapsulated coil antenna installed inside the deposition chamber. As the ICP power increased from 0 to 500W, the crystalline grain size decreased. It is believed that the decrease in the crystal grain size at higher ICP powers is due to resputtering of the coatings as a result of ion bombardment as well as film densification. The preferential orientation of CrN coatings changed from (111) to (200) with an increase in the ICP power. The ICP magnetron sputtering CrN coatings showed excellent surface roughness compared to the DC magnetron sputtering coatings.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.281-284
• /
• 2004

In Recent, it became necessary to envelope the technology about electrodeless fluorescent lamp according to demand of the electrodeless fluorescent lamp system that used higher efficiency and advantage of long-lifetime. Especially, in the electrodeless fluorescent lamp which used H-mode, efficiency of lamp is decided from matching parameter of antena and inverter So it is of the utmost importance to design antena and inverter. Therefore, this paper used a transformer principle for efficiency rising of electrodeless fluorescent lamp and interpreted an equivalent circuit, used an impedance analyzer in order to confirm a performance enhancement of lamp along design of antenna, and confirmed parameter characteristic of R, L, C, Z, Phase, Q-factor along a change of magnetic flux density. Also, this paper confirmed a luminance characteristic of electrodeless lamp along parameter change with measuring optical characteristic along a change of magnetic flux density.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.171-176
• /
• 2013

In this paper, we present a MEMS (micro-electro-mechanical system) implantable blood pressure sensor which has designed and fabricated with consideration of size, design flexibility, and wireless detection. Mechanical and electrical characterizations of the sensor were obtained by mathematical analysis and computer aided simulation. The sensor is composed of two coils and a air gap capacitor formed by separation of the coils. Therefore, the sensor produces its resonant frequency which is changed by external pressure variation. This frequency movement is detected by inductive coupling between the sensor and an external antenna coil. Theoretically analyzed resonant frequency of the sensor under 760 mmHg was calculated to 269.556 MHz. Fused silica was selected as sensor material with consideration of chemical and electrical reaction of human body to the material. $2mm{\times}5mm{\times}0.5mm$ pressure sensors fitted to radial artery were fabricated on the substrates by consecutive microfabrication processes: sputtering, etching, photolithography, direct bonding and laser welding. Resonant frequencies of the fabricated sensors were in the range of 269~284 MHz under 760 mmHg pressure.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.10
• /
• pp.40-45
• /
• 2007

Lightning warning system plays an important role in protecting human life and other facilities from lightning return strokes. This paper dealt with lightning positioning algorithms and circuits as a main function of lightning warning system, which monitor movements and activities of thunderclouds. Electric field component produced by lightning discharge is detected by the configuration of a whip antenna and a narrow-band resonance amplifier with center frequency of 300[kHz]. Measurement circuit of magnetic field waveform consists of a crossed-loop coil and an integral amplifier, and its frequency bandwidth is ranges from 5[kHz] to 1.2[MHz]. The polarity of lightning discharge is discriminated by electric field component. After-fixing the polarity, we can calculate the direction and distance of lightning discharge by the peak and the zero-cross time of magnetic field waveform.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.1
• /
• pp.41-45
• /
• 2016

The technology of supplying the electric power by wireless power transfer (WPT) is expected for the next generation power feeding system since it can supply the power to portable devices without any connectors through large air gap. As such a technology based on strongly coupled electromagnetic resonators is possible to deliver the large power and recharge them seamlessly; it has been considered as a noble option to wireless power charging system in the various power applications. Recently, various HTS wires have now been manufactured for demonstrations of transmission cables, motors, MAGLEV, and other electrical power components. However, since the HTS magnets have a lower index n value intrinsically, they are required to be charged from external power system through leads or internal power system. The portable area is limited as well as the cryogen system is bulkier. Thus, we proposed a novel design of wireless power charging system for superconducting HTS magnet (WPC4SM) based on resonance coupling method. As the novel system makes possible a wireless power charging using copper resonance coupled coils, it enables to portable charging conveniently in the superconducting applications. This paper presented the conceptual design and operating characteristics of WPC4SM using different shapes' copper resonance coil. The proposed system consists of four components; RF generator of 370 kHz, copper resonance coupling coils, impedance matching (IM) subsystem and HTS magnet including rectifier system.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.125-125
• /
• 2018

반도체 소자의 미새화에 따라 선폭이 10nm 이하로 줄어듦에 따라, 금속 배선의 저항이 급격하게 상승하고 있다. Cu는 낮은 저항과 높은 전도도를 가지고 있어 현재 배선물질로써 가장 많이 사용되고 있지만, 소자가 미세화됨에 따라 Cu를 미래의 배선물질로써 계속 사용하기에는 몇 가지 문제점이 제기되고 있다. Cu는 electron mean free path (EMFP)가 39 nm로 긴 특성을 가지기 때문에, 선폭이 줄어듦에 따라 surface 및 grain boundary scattering이 증가하여 저항이 급격하게 증가한다. 또한, technology node에 따른 소자의 operating temperature와 current density의 증가로 인해 Cu의 reliability가 감소하게 된다. 텅스텐은 EMFP가 19 nm로 짧은 특성을 가지고 있어, 소자의 크기가 줄어듦에 따라 Cu보다 낮은 저항 특성을 가질 수 있으며, 녹는점이 3695K로 1357K인 Cu보다 높으므로 배선물질로써 Cu를 대체할 가능성이 있다. 본 연구에서는 Inductively Coupled Plasma (ICP) assisted magnetron sputtering을 통해 매우 얇은 텅스텐 박막을 증착하여 저항을 낮추고자 하였다. 고밀도 플라즈마의 방전을 위해, internal-type coil antenna를 사용하였으며 텅스텐 박막의 증착을 위해 DC sputter system이 사용되었다. 높은 에너지를 가진 텅스텐 이온을 이용하여 낮은 온도에서 고품위 박막을 증착할 수 있었으며, dense한 구조의 박막 성장이 가능하였다. ICP assisted를 이용하여 증착했을 때와, 그렇지 않을 때를 비교하여 ICP 조건에 따라서 박막의 저항이 감소함을 확인할 수 있었을 뿐만 아니라 최대 약 65% 감소함을 확인할 수 있었다. XRD를 이용하여 ICP power를 인가했을 때, 높은 저항을 갖는 A-15 구조를 가진 ${\beta}$ peak의 감소와 낮은 저항을 갖는 BCC 구조를 가진 ${\alpha}$ peak의 증가를 상온과 673K에서 증착한 박막 모두에서 확인하였으며, 이를 통해 ICP power가 저항 감소에 영향을 미친다는 것을 확인하였다. 또한, 두 온도 조건에서 grain size를 계산하여 ICP power를 인가함에 따라 두 조건 모두 grain size가 증가하였음을 조사하였다. 또한, XPS 분석을 통해 ICP power를 인가하였을 때 박막의 저항에 많은 영향을 끼치는 O peak이 감소하는 것을 통해 ICP assisted의 효과를 확인하였다. 이를 통해, ICP assisted magnetron sputtering을 통해 텅스텐 박막을 증착함으로써 차세대 배선물질로써 텅스텐의 가능성을 확인할 수 있었다.