• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.77-80
• /
• 2001

Crystallographic and magnetic characteristics of CoCr-based magnetic thin film for perpendicular magnetic recording media were influenced on preparing conditions. In these, there is that substrate temperature was parameter that increases perpendicular coercivity of CoCrTa magnetic layer using recording layer. While preparation of CoCr-based doublelayer, by optimizing substrate temperature, we expect to increase perpendicular anisotropy of CoCr magnetic layer and prepare ferromagnetic recording layer with a good quality by epitaxial growth. CoCrTa/Si doublelayer showed a good dispersion angle of c-axis orientation $\Delta\theta_{50}$ caused by inserting amorphous Si underlayer which prepared at underlayer substrate temperature 250C. Perpendicular coercivity was constant, in-plane coercivity was controlled a low value about 200Oe. This result implied that Si underlayer could restrain growth of initial layer of CoCrTa thin film, which showed bad magnetic properties effectively without participating magnetization patterns of magnetic layer. In case of CoCrTa/Si that prepared with ultra thin underlayer, crystalline orientation of CoCrTa was improved rather underlayer thickness 1nm, it was expected that amorphous Si layer played a important role in not only underlayer but also seed layer.

• Journal of Magnetics
• /
• 제3권1호
• /
• pp.4-8
• /
• 1998

Two different compositions of melt spun magnetic alloys, $ Nd_4Fe_{80}B_{16} and Nd_4Fe_{76}Co}\_3Hf_{0.5}Ga_{0.5}B_{16},$ were characterized in terms of magnetic properties and thermal behaviors. It was found that the addition of Hf and Ga effectively slow down the crystallization rate of the nanocomposite $ Nd_2Fe_{14}B/Fe_3B$ magnet. Coercivity(iHc) changes only slightly with varying the post annealing conditions confirming that iHc is not a sensitive magnetic quantity as a function of grain size and exchange coupled interaction. The experimentally observed behaviors of Mr and Hc do not vary monotonously with in-creasing grain size which is not in agreement with the numerically calculated result near the critical grain size (dc). The plot of the grain size dependence for the remanence and coercivity in isotrop!c nanocomposite magnets has been revised in this study. The maxium energy product, $(B, H)_{max}$ =15.34 MGOe, and a reduced remanence, Mr/Ms=0.84 were obtained, respectively.

• 한국표면공학회지
• /
• 제34권5호
• /
• pp.494-498
• /
• 2001

Ferromagnets(FM)-Al-$O_{x}$ -Ferromagnets (FM) tunneling junctions were evaluated by changing the fabricating conditions of an Al-X$/_{x}$ layer. The junction composed of a thicker Al-$O_{x}$ shows the low resistance and the stable MR ratio about 16% in a wide range of oxidation time. For the junctions with the thinner Al-$O_{x}$ , they showed a fast increase of the barrier width as an increase of an oxidation time and exhibited a strong bias dependence. As oxidation time increased, the coercivity ($H_{c}$ ) of bottom Co layer increased gradually due to the local oxidation of Co bottom layer at a interface. However, the small formation of Co oxide did not largely influence on the deterioration of MR ratio.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.537-540
• /
• 2003

This study was investigated to fabricate the porcelain materials with high magnetic characteristics. The high characteristics of the magnetic porcelain materials were achieved at the following conditions; powder sizes of isotropic Sr-ferrites with $1{\sim}2\;mm$ and magnetic powder infraction of 30 wt%. The magnetic tea cups with 3-mm-thick at the optimum conditions indicated the high magnetic characteristics such as the surface flux density of 178 G, the remanent flux density of 240 G, and the intrinsic coercivity of 3910 Oe.

• Journal of Magnetics
• /
• 제5권3호
• /
• pp.106-109
• /
• 2000

The single stroke hot deformation is a simple method fur the fabrication of anisotropic NdFeB magnets. In order to obtain the optimum conditions, Taguchi method of experimental design was applied in this work. The optimum conditions obtained on the basis of coercivity in Taguchi analysis was a little different from those of remanence and maximum energy Product. The contribution of each factor to magnetic Properties was calculated in detail.

• 한국재료학회지
• /
• 제31권2호
• /
• pp.61-67
• /
• 2021

Fabrication of a ferromagnetic composite powder for the magnesium and BaFe12O19 system by mechanical alloying (MA) is investigated at room temperature. Mixtures of Mg and BaFe12O19 powders with a weight ratio of Mg:BaFe12O19 = 4:1, 3:2, 2:3 and 1:4 are used. Optimal MA conditions to obtain a ferromagnetic composite with fine microstructure are investigated by X-ray diffraction, differential scanning calorimetry (DSC) and vibrating sample magnetometer (VSM) measurement. It is found that Mg-BaFe12O19 composite powders in which BaFe12O19 is dispersed in Mg matrix are successfully produced by MA of BaFe12O19 with Mg for 80 min. for all compositions. Magnetization of Mg-BaFe12O19 composite powders gradually increases with increasing the amounts of BaFe12O19, whereas coercive force of MA powders gradually decreases due to the refinement of BaFe12O19 powders with MA time for all compositions. However, it can be seen that the coercivity of Mg-BaFe12O19 MA composite powders with a weight ratio of Mg:BaFe12O19=4:1 and 3:2 for MA 80 min. are still high, with values of 1260 Oe and 1320 Oe compared to that of Mg:BaFe12O19=1:4. This clearly suggests that the refinement of BaFe12O19 powders during MA process for Mg:BaFe12O19=4:1 and 3:2 tends to be suppressed due to ductile Mg powders.

• 한국분말재료학회지
• /
• 제22권3호
• /
• pp.216-220
• /
• 2015

Vertically oriented nickel nanowire arrays with a different diameter and length are synthesized in porous anodic aluminium oxide templates by an electrodeposition method. The pore diameters of the templates are adjusted by controlling the anodization conditions and then they are utilized as templates to grow nickel nanowire arrays. The nickel nanowires have the average diameters of approximately 25 and 260 nm and the crystal structure, morphology and microstructure of the nanowires are systematically investigated using XRD, FE-SEM and TEM analysis. The nickel nanowire arrays show a magnetic anisotropy with the easy axis parallel to the nanowires and the coercivity and remanence enhance with decreasing a wire diameter and increasing a wire length.

• 대한수학회보
• /
• 제32권2호
• /
• pp.343-348
• /
• 1995

Let X and Y be two normed spaces and D a nonempty convex subset of X. Let $T : X \ to L(X,Y)$ be a mapping, where L(X,Y) is the space of all continuous linear mappings from X into Y. And let $C : D \to 2^Y$ be a set-valued map such that for each $x \in D$, C(x) is a convex cone in Y such that Int $C(x) \neq 0 and C(x) \neq Y$, where Int denotes the interior.

• 한국전기전자재료학회논문지
• /
• 제17권8호
• /
• pp.882-887
• /
• 2004

The new magnetic porcelain materials have been studied by mixing magnetic St-ferrite powders with traditional porcelain materials before forming process. For the maintenance of magnetic characteristics after glaze firing process, the Sr-ferrite grains with the size of 1∼2 ${\mu}{\textrm}{m}$ were agglomerated as the isotropic granules with the size of 0.5∼2 mm. The high characteristics of magnetic porcelain materials were achieved at the following conditions; isotropic Sr-ferrite granules of 30 wt%, granule size of 1.4∼2 mm, and glaze firing temperature of $1250^{\circ}C$ in air The magnetic porcelain materials indicated the high magnetic properties, such as the remanent flux density of 240 G, the intrinsic coercivity of 3910 Oe, and the surface flux density of 178 G. The extraction properties of the magnetic tea cups were high compared to that of the traditional tea cups.

• 한국세라믹학회지
• /
• 제28권2호
• /
• pp.93-100
• /
• 1991

For determination the optimum manufacturing condition Fe4N powder for magnetic recording media, we have studied the following important conditions : the effect of particle size of metal powder on the nitridation, the condition of nitridation on the formation and magnetic properties of Fe4N, and stability of Fe4N powder against temperature and change on standing. The results can be summarized as : 1) Single phase Fe4N is formed at 50v/o of ammonia concentration during the nitridation reaction, 2) Single phase Fe4N is formed above 40$0^{\circ}C$, 15min regardless of the metal powder sizes, 3) Coercivity and saturation magnetization of Fe4N powder almost constant value until 20 day-passing from preparation date.