• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.297-306
• /
• 2014

The paper presents the numerical analysis of wave run-up over rubble-mound breakwaters covered by antifer units using a technique integrating Computer-Aided Design (CAD) and Computational Fluid Dynamics (CFD) software. Direct application of Navier-Stokes equations within armour blocks, is used to provide a more reliable approach to simulate wave run-up over breakwaters. A well-tested Reynolds-averaged Navier-Stokes (RANS) Volume of Fluid (VOF) code (Flow-3D) was adopted for CFD computations. The computed results were compared with experimental data to check the validity of the model. Numerical results showed that the direct three dimensional (3D) simulation method can deliver accurate results for wave run-up over rubble mound breakwaters. The results showed that the placement pattern of antifer units had a great impact on values of wave run-up so that by changing the placement pattern from regular to double pyramid can reduce the wave run-up by approximately 30%. Analysis was done to investigate the influences of surface roughness, energy dissipation in the pores of the armour layer and reduced wave run-up due to inflow into the armour and stone layer.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.5-9
• /
• 2007

The construction method for Foamed-Concrete has not been important due to following process of construction work. However, according to the code about enhance of energy saving design policy and impact noise, noised isolation has been used in construction site so that the resistance for cracking and capability for insulating of Foamed-Concrete has been required. Therefore, new alternatives are demanded. Optimum mixing design, which can get the improvement of insulation and resistance of crack for Foamed-Concrete adding EVA chip, was derived and also the device, applying to construction site, was invented to equalize quality. This device can measure quantity of all input and placement, and show up the sum of placement and mixing design on a touch screen. This valuable construction method is friendly environment and recycling method because of using EVA chip, by-product of an EVA insole scrap burned or embedded, as a light-weight aggregate.

• Smart Structures and Systems
• /
• v.16 no.2
• /
• pp.243-262
• /
• 2015

Optimal sensor placement (OSP) is a critical issue in construction and implementation of a sophisticated structural health monitoring (SHM) system. The uncertainties in the identified structural parameters based on the measured data may dramatically reduce the reliability of the condition evaluation results. In this paper, the information entropy, which provides an uncertainty metric for the identified structural parameters, is adopted as the performance measure for a sensor configuration, and the OSP problem is formulated as the multi-objective optimization problem of extracting the Pareto optimal sensor configurations that simultaneously minimize the appropriately defined information entropy indices. The nondirective movement glowworm swarm optimization (NMGSO) algorithm (based on the basic glowworm swarm optimization (GSO) algorithm) is proposed for identifying the effective Pareto optimal sensor configurations. The one-dimensional binary coding system is introduced to code the glowworms instead of the real vector coding method. The Hamming distance is employed to describe the divergence of different glowworms. The luciferin level of the glowworm is defined as a function of the rank value (RV) and the crowding distance (CD), which are deduced by non-dominated sorting. In addition, nondirective movement is developed to relocate the glowworms. A numerical simulation of a long-span suspension bridge is performed to demonstrate the effectiveness of the NMGSO algorithm. The results indicate that the NMGSO algorithm is capable of capturing the Pareto optimal sensor configurations with high accuracy and efficiency.

• Smart Structures and Systems
• /
• v.15 no.5
• /
• pp.1373-1392
• /
• 2015

Placing sensors at appropriate locations is an important task in the design of an efficient structural health monitoring (SHM) system for a large-scale civil structure. In this paper, a hybrid optimization algorithm called virus monkey algorithm (VMA) based on the virus theory of evolution is proposed to seek the optimal placement of sensors. Firstly, the dual-structure coding method is adopted instead of binary coding method to code the solution. Then, the VMA is designed to incorporate two populations, a monkey population and a virus population, enabling the horizontal propagation between the monkey and virus individuals and the vertical inheritance of monkey's position information from the previous to following position. Correspondingly, the monkey population in this paper is divided into the superior and inferior monkey populations, and the virus population is divided into the serious and slight virus populations. The serious virus is used to infect the inferior monkey to make it escape from the local optima, while the slight virus is adopted to infect the superior monkey to let it find a better result in the nearby area. This kind of novel virus infection operator enables the coevolution of monkey and virus populations. Finally, the effectiveness of the proposed VMA is demonstrated by designing the sensor network of the Canton Tower, the tallest TV Tower in China. Results show that innovations in the VMA proposed in this paper can improve the convergence of algorithm compared with the original monkey algorithm (MA).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.9 s.351
• /
• pp.31-37
• /
• 2006

Low-density parity-check (LDPC) codes are recently emerged due to its excellent performance. The standard for European high definition satellite digital video broadcast, DVB-S2 has adopted LDPC codes as a channel coding scheme. This paper proposes a DVB-S2 LDPC decoder architecture using a hybrid parity check matrix which is efficient in hardware implementation for both decoders and encoders. The hybrid H-matrices are constructed so that both the semi-random technique and the partly parallel structure can be applied to design encoders and decoders. Using the hybrid H-matrix scheme, the architecture of LDPC decoder for DVB-S2 can be very practical and efficient. In addition, we show a new Variable Node processor Unit (VNU) architecture to reuse the VNU for various code rates and optimized block memory placement to reuse. We design a DVB-S2 LDPC decoder of code rate 1/2 usng the proposed architecture. We estimate the performance of the DVB-S2 LDPC decoder and compare it with other decoders.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.27-33
• /
• 1999

This paper describes a new algorithm for irregular shapes allocation (known as nesting) and cutting path optimization, both implemented in PC-based software with graphic user interface (GUI). Main characteristic of the nesting W is that it deals with only vertices of Placed Pieces to reduce calculation time and for effective allocation. And the other characteristic of the nesting program is that every parts are grouped with respect to their areas and placed along the column of placement region. The cutting paths can be determined by an optimization method called simulated annealing. It was shown that the developed code is superior to other previous nesting H in elapsed time and waste ratio.

• Smart Structures and Systems
• /
• v.17 no.5
• /
• pp.725-742
• /
• 2016

This paper is focused on stiffness ratio effect and a new method to specify the best pattern of piezoelectric patches placement around a hole in a plate under tension to reduce the stress concentration factor. To investigate the stiffness ratio effect, some different values greater and less than unity are considered. Then a python code is developed by using particle swarm optimization algorithm to specify the best locations of piezoelectric actuators around the hole for each stiffness ratio. The results show that, there is a line called "reference line" for each plate with a hole under tension, which can guide the location of actuator patches in plate to have the maximum stress concentration reduction. The reference line also specifies that actuators should be located horizontally or vertically. This reference line is located at an angle of about 65 degrees from the stress line in plate. Finally two experimental tests for two different locations of the patches with various voltages are carried out for validation of the results.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1715-1719
• /
• 2004

An in-house supersonic ejector was designed to ensure low pressure and high speed scavenging of resonating cavity of chemical lasers. For given primary flow condition, 100g/s secondary mass flow rate was observed at the design pressure. Performance validation of a supersonic ejector system along with an investigation of effects of supersonic diffuser was conducted. Placement of diffuser at the secondary inlet further reduced diffuser upstream pressure to 1/4-1/5 relieving the local to the primary supply unit. In order to increase the secondary flow, we put two ejectors capable of removing 50g/s each of secondary flows together to deal with higher mass flow. Test of the parallel unit demonstrated the secondary flow rate was proportional to the numbers of individual units that were brought together. Additionally, flow calculations with a commercial code were carried out in every case of experiment and compared with results.

• Proceedings of the Korean Information Science Society Conference
• /
• 2005.07a
• /
• pp.784-786
• /
• 2005

SPM (Scratch-Pad Memory)을 위한 코드 배치 기법과 demand paging기법을 Post pass optimizer를 사용하여 구현한다. 코드 배치 문제는 ILP (Integer Linear Programming) 문제로 변환하여 해결한다. 최적 화기는 ILP 해답의 질을 높이기 위해 응용 프로그램의 프로파일 정보를 사용하고, 코드로부터 natural loop을 추출한다. 또한 SPM을 사용하여 demand paging을 할수 있도록 추가 코드를 삽입한다. 이 기법을 사용해 6개의 내장형 응용 프로그램을 실험하였고, 프로그램 크기의 $20\%$에 해당하는 SPM에 대해 전력 소모는 $75.9\%$로 감소하였고 성능은 $54.5\%$ 증가하였다.

• The Korean Journal of Air & Space Law and Policy
• /
• v.27 no.2
• /
• pp.211-241
• /
• 2012

The Draft International Code of Conduct for Outer Space Activities officially proposed by the European Union on the occasion of the 55th Session of the United Nations Peaceful Uses of the Outer Space last June 2012 in Vienna, Austria is to fill the lacunae of the relevant norms to be applied to the human activities in the outer space and thus has the merit our attention. The missing elements of the norms span from the prohibition of an arms race, safety and security of the space objects including the measures to reduce the space debris to the exchange of information of space activities among space-faring nations. The EU's initiatives, when implemented, cover or will eventually prepare for the forum to deal with such issues of interests of the international community. The EU's initiatives begun at the end of 2008 included the unofficial contacts with major space powers including in particular the USA of which position is believed to have been reflected in the Draft with the aim to have it adopted in 2013. Although the Code is made up of soft law rather than hard law for the subscribing countries, the USA seems to be afraid of the eventuality whereby its strategic advantages in the outer space will be affected by the prohibiting norms, possibly to be pursued by the Code from its current non-binding character, of placing weapons in the outer space. It is with this trepidation that the USA has been opposing to the adoption of the United Nations Assembly Resolutions on the prevention of an arms race in the outer space (PAROS) and in the same context to the setting-up of a working group on the arms race in the outer space in the frame of the Conference on Disarmament. China and Russia who together put forward a draft Treaty on Prevention of the Placement of Weapons in Outer Space and of the Threat or Use of Force against Outer Space Objects (PPWT) in 2008 would not feel comfortable either because the EU initiatives will steal the lime light. Consequently their reactions are understandably passive towards the Draft Code while the reaction of the USA to the PPWT was a clear cut "No". With the above background, the future of the EU Code is uncertain. Nevertheless, the purpose of the Code to reduce the space debris, to allow exchange of the information on the space activities, and to protect the space objects through safety and security, all to maximize the principle of the peaceful use and exploration of the outer space is the laudable efforts on the part of EU. When the detailed negotiations will be held, some problems including the cost to be incurred by setting up an office for the clerical works could be discussed for both efficient and economic mechanism. For example, the new clerical works envisaged in the Draft Code could be discharged by the current UN OOSA (Office for Outer Space Affairs) with minimal additional resources. The EU's initiatives are another meaningful contribution following one due to it in adopting the Kyoto Protocol of 1997 to the UNFCCC (UN Framework Convention on the Climate Change) and deserve the praise from the thoughtful international community.