• Journal of the Korean institute of surface engineering
• /
• v.34 no.1
• /
• pp.3-9
• /
• 2001

The purpose of this study is to evaluate the properties of the functional gradient thermal barrier coatings by plasma spray process. The evaluations of mechanical and thermal properties such as fatigue, oxidation and wear-resistance at high temperatures have been conducted. Furthermore, residual stress and bond strength have been evaluated. The range of thickness of coated layers was 550~600$\mu\textrm{m}$. The range of hardness of layers was 800~900 Hv and the porosity range of coatings was about 7 to 14%. The top coating layer of $ZrO_2$ in thermal barrier was composed of tetragonal structure after spraying. The coated layers of $ZrO_2$ on the Inconel substrate is the best resistance for thermal fatigue. Those coatings had the least compressive stress in comparison with other coatings. In high temperature oxidation test, the coatings on Inconel substrate was better than the coatings on SUS substrate. The bond strength of the concave type was greater than that of linear types and convex types coatings.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.4
• /
• pp.321-326
• /
• 2001

The TiCrN Coatings haying three kinds of Compositions of $Ti_{36}$ $Cr_{26}$ $N_{38}$ , $Ti_{31}$ $Cr_{35}$ $N_{34}$ / and $Ti_{14}$ $Cr_{52}$ $N_{34}$ were deposited on STD 61 steel substrate by arc ion plating and were oxidized between 700 and 100$0^{\circ}C$ to identify the oxide scales formed on the coatings. The oxide scales were then analyzed using EPMA, XRD and GAXRD. During oxidation, the coatings consisting of TiN and CrN phases were reduced to TiO2 and $Cr_2$$O_3$, respectively. Titania tended to form at the outer oxide layer, whereas chromia tended to form at the inner oxide layer, owing to the different oxygen affinity. The substrate elements as well as coating elements diffused outwardly toward the oxide layer due to the concentration gradient. The growth of oxide from the TiCrN coatings was schematically expressed on the basis of thickness measurement of the reacted and unreacted coatings. The Cr element showed its stronger role to keep the TiCrN coatings from oxidation, when compared with Ni.

• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.313-317
• /
• 2018

Carbon-based coatings, including carbon nanotubes (CNTs), graphene, and buckyball ($C_{60}$), receive much interest because of their outstanding mechanical and electrical properties for a wide range of electromechanical component-based applications. Previous experimental results demonstrate that these carbon-based coatings are promising solid lubricants because of their superior tribological properties, and thus help prolong the lifetime of silicon-based applications. In this study, CNT coatings are deposited on a bare silicon (100) substrate by electrodynamic spraying under different deposition conditions. During the coating deposition, the applied voltage, CNT concentration of the solution, distance between the injecting nozzle and the substrate and diameter of the injecting nozzle are optimized to control the thickness and surface roughness of the CNT coatings. The surface morphology and thickness of the coatings are characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. The friction and wear properties of the coatings are investigated by using a pin-on-reciprocating-type tribotester under various experimental conditions. The friction coefficient of the CNT coating is as low as 0.15 under high normal loads. The overall results reveal that CNT coatings deposited by electrodynamic spraying provide relatively uniform with superior lubrication performance.

• Corrosion Science and Technology
• /
• v.17 no.6
• /
• pp.257-264
• /
• 2018

Anti-graffiti coatings have become more important. These layers must guarantee excellent corrosion protection properties, and graffiti must be easily removable, without reducing protection and aesthetic properties. In this study, anti-graffiti and corrosion behavior of two anti-graffiti polyurethane powder coatings were studied. These layers were deposited on aluminum substrate, with two different surface finishes, smooth, and wrinkled. The action of four different removers are investigated. Graffiti were drawn on coatings by means of red acrylic spray paint. Methyl-ethyl-ketone (MEK) and a "commercial" remover were the most effective solvents, in terms of graffiti removal capability, producing limited change in aesthetical surface aspect for smooth finishing. The wrinkled surface was less resistant. Corrosion protection properties, after removal action and contact with the remover, were evaluate by electrochemical impedance spectroscopy. After approximately 5 hours, coatings were no longer protective due to formation of defects. To simulate the weathering effect, UV-B cyclic test (4 hours of UV exposure followed by 4 hours of saturated humidity at $50^{\circ}C$) were performed for 2000 hours. Gloss and color changes were measured, and electrochemical impedance spectroscopy measurements were performed after aging and graffiti removal.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.3
• /
• pp.133-138
• /
• 2021

Ternary Ti-X-N coatings, where X = Al, Si, Cr, O, etc., have been widely used for machining tools and cutting tools such as inserts, end-mills, and etc. Ti-Al-N-O coatings were deposited onto silicon wafer and WC-Co substrates by a cathodic arc evaporation (CAE) technique at various negative substrate bias voltages. In this study, the influence of substrate bias voltages during deposition on the microstructure and mechanical properties of Ti-Al-N-O coatings were systematically investigated to optimize the CAE deposition condition. Based on results from various analyses, the Ti-Al-N-O coatings prepared at substrate bias voltage of -80 V in the process exhibited excellent mechanical properties with a higher compressive residual stress. The Ti-Al-N-O (-80 V) coating exhibited the highest hardness around 30 GPa and elastic modulus around 303 GPa. The improvement of mechanical properties with optimized bias voltage of -80 V can be explained with the diminution of macroparticles, film densification and residual stress induced by ion bombardment effect. However, the increasing bias voltage above -80 V caused reduction in film deposition rate in the Ti-Al-N-O coatings due to re-sputtering and ion bombardment phenomenon.

• Corrosion Science and Technology
• /
• v.22 no.6
• /
• pp.393-398
• /
• 2023

Properties of hafnium nitride (HfN) coatings are affected by deposition conditions, most often by the sputtering technique. Appropriate use of different magnetron sputtering modes allows control of the structural development of the film, thereby enabling adjustment of its properties. This study compared properties of HfN coatings deposited by direct current magnetron sputtering (dcMS), mid-frequency direct current magnetron sputtering (mfMS), and inductively coupled plasma-assisted magnetron sputtering (ICPMS) systems. The microstructure, crystalline, and mechanical properties of these HfN coatings were investigated by field emission electron microscopy, X-ray diffraction, atomic force microscopy, and nanoindentation measurements. HfN coatings deposited using ICPMS showed smooth and highly dense microstructures, whereas those deposited by dcMS showed rough and columnar structures. Crystalline structures of HfN coatings deposited using ICPMS showed a single δ-HfN phase, whereas those deposited using dcMS and mfMS showed a mixed δ-HfN and HfN_0.4 phases. Their performance were increased in the order of dcMS < mfMS < ICPMS, with ICPMS achieving a value of 47.0 GPa, surpassing previously reported results.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.2
• /
• pp.124-139
• /
• 2007

In order to obtain the maximum flame retardancy with the minimal deterioration of physical properties of PU flame-retardant coatings, chlorine and phosphorous functional groups were introduced into the pre-polymer of modified polyesters. In the first step, the tetramethylene bis(orthophosphate) (TBOP) and neohexanediol dichloroacetate (DCA-adduct) intermediates were synthesized. In the second step, 1,4-butanediol and adipic acid monomers were polymerized with the two kind of intermediates to obtain copolymer. The modified polyesters containing chlorine and phosphorous (ATBA-10C, -20C, and -30C) were synthesized by adjusting the contents of chlorine compound (dichloroacetic acid, 10, 20, 30 wt%) with fixed the content of phosphorous compound (2 wt%). The PU flame-retardant coatings (TTBAH -10C, -20C, and -30C) were prepared using the synthesized ATBAs and HDI-trimer as curing agent at room temperature. The physical properties of PU flame-retardant coatings with chlorine and phosphorous were inferior to those with phosphorous only and the properties were getting worse with increasing chlorine content. Flame retardancy was tested with three methods. With the vertical method, Complete combustion time of ATBAHs were $259^{\sim}347$ seconds, which means that the prepared coatings are good flame-retardant. With the $45^{\circ}$ Meckel burner method, char lengths of the three prepared coatings were less than 2.9 cm, which indicates that the prepared coatings are 1st grade flame retardancy. With the limiting oxygen index (LOI) method, the LOI values of the three prepared coatings were in the range of $30^{\sim}35%$, which proves good flame retardancy of the prepared coatings. From the results of flame retardancy tests of the specimens that contain the same amounts of flame retarding compounds, it was found that the coatings containing both phosphorous and chlorine show higher flame retardancy than the coatings containing phosphorous alone. This indicates that some synergy effect of flame retardancy exists between phosphorous and chlorine.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.133-134
• /
• 2002

The use of low friction wear resistant coatings for machine components is rapidly increasing. These components may operate in any lubrication regime, and less frequently even unlubricated. When run unlubricated it is easy to see the beneficial effect of a low friction coating. However, it has frequently been shown that the coating may also be very beneficial under boundary and mixed lubrication conditions. The present digest briefly presents a few interesting aspects of the use of low friction coatings in lubricated contact illustrated by selected experimental results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.1061-1066
• /
• 2003

Chloride penetration into concrete is the main cause of the steel corrosion in concrete structures exposed to chloride-rich environments. Protective surface coatings are increasingly being applied to concrete structures to reduce chloride penetration. In this study, the performance of various surface coatings was evaluated. Most coatings showed good results for the various tests of the performance evaluation. Surface coatings can delay deterioration such as chloride-induced reinforcing bar corrosion effectively.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.4
• /
• pp.291-295
• /
• 2003

Many steam turbine components encounter solid particle erosion damage. It has been reported that particle erosion damage is caused by oxide scale exfoliation from boiler tubes. One of the most effective solutions to combat the erosion damage is the application of erosion resistant coatings on the turbine components. In this study, particle erosion resistance for various hard coatings such as nitride, Cr carbide and boride coatings was evaluated under the simulated erosion conditions of steam turbines. Based on the particle erosion tests, the boride coating was found to be more superior to others.