• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.349-349
• /
• 2005

수동소자를 PCB(Printed Circuit Board) 안으로 집적하기 위한 방법의 일환으로 polymer-metal, polymer-ceramic composite에 연구가 국내외 연구 국내외 연구기관에서 광범위하게 진행되고 있다. 본 연구에서는 polymer-metal-ceramic composite 에서 PZT-coated Ni의 volume fraction에 따른 유전율 변화에 대하여 조사하였다. 원료로는 PZT(52/48) solution. 니켈금속분말, PMMA(polymethyl methacrylate)를 사용하였다. 전기적 특성은 임피던스분석기를 이용하여 측정하였으며 mixing rule과 percolation theory를 이용하여 결과를 해석하였다.

• 한국기계가공학회지
• /
• 제21권5호
• /
• pp.77-83
• /
• 2022

A high-hardness tool material is required to reduce extreme abrasive wear when drilling carbon fiber reinforced plastic (CFRP). Single-crystal diamond is the hardest material in the world, but it is very expensive to be used as a cutting tool. Polycrystalline diamond (PCD) is a diamond grit fused at a high temperature and pressure, and diamond-like carbon (DLC) is an amorphous carbon with high hardness. This study compares DLC coatings and PCD inserts to conventional TiAlN-coated tungsten carbide drills. In fiberglass and carbon fiber reinforced polymer drilling, the tool wear of DLC-coated carbide was approximately half that of TiAlN-coated tools, and slight tool wear occurred in the case of PCD insert end drills.

• 대한금속재료학회지
• /
• 제50권8호
• /
• pp.563-568
• /
• 2012

The wetting property and reflectivity of Sn-3.5Ag solder which was dip coated on a LED lead frame were investigated. The wettability of molten solder on Cu substrate was evaluated by the wetting balance tester, and surface tension was calculated from maximum withdrawal force and withdrawal time. Temperature of the molten solder in a bath was varied in the range of $250-290^{\circ}C$. With increasing temperature, the surface tension decreased a little. The reflectivity of Sn-3.5Ag coated on a substrate became a little lower than the highest current LED lead frame reflectivity.

• Corrosion Science and Technology
• /
• 제11권1호
• /
• pp.29-36
• /
• 2012

The resistance spot welding of high strength steel degrades the weldability because of its high strength with rich chemical composition and coating layer to protect from corrosion. During the each resistance welding process the electrodes tip reacts with coating layer, then subsequently deteriorates and shorten electrode life. In this study, the Al-coated HPF (Hot Press Forming) steels and Zn-coated TRIP steels were used to investigate the electrode life for resistance spot welding. Experimental results show that the reactivity of Al-coating on HPF steels to electrode tip surface behaviors different from the conventional Zn-coated high strength steels. The electrode tip diameter and nugget size in electrode life test of Al-coated HPF steels are observed to be constant with respect to weld numbers. For Al-coated HPF steels, the hard aluminum oxide layer being formed during high temperature heat treatment process reduces reactivity with copper electrode during the resistance welding process. Eventually, the electrode life in resistance spot welding of Al-coated HPF steels has the advantage over the galvanized steel sheets.

• Investigative Magnetic Resonance Imaging
• /
• 제13권2호
• /
• pp.171-176
• /
• 2009

목적 : 자기공명영상 장비에서 신호를 주고 받는 주요 부분인 RF 코일의 성능 특성인 Q 값 (quality factor)과 신호대잡음비 (SNR, signal-to-noise ratio) 값에 미치는 코일 구리선 코팅 재질의 영향을 조사하고자 하였다. 대상 및 방법 : 폴리에스테르 (polyester), 폴리우레탄 (polyurethane), 폴리이미드 (polyimide), 폴리아마이드이미드 (polyamideimide), 폴리에스테르이미드 (polyester-imide)가 코팅된 직경 0.4 mm 구리선을 사용하여, 내경이 1.7mm인 RF 코일을 솔레노이드 형태로 제작한 후 network analyzer로 Q 값을 측정하였다. 또한 제작된 RF 코일을 600 MHz MRI (14.1 T, Bruker DMX600) 장비를 이용하여 표준시료를 이용한 자기공명영상 실험을 수행하였으며, 5개의 다른 코팅 재질과 코팅이 없는 경우에 대하여 영상에서의 신호대잡음비를 비교하였다. 결과 : 코팅 피복을 벗겨내고 측정한 신호대잡음비는 오차 범위에서 유사하였으며, 코팅되어 있는 경우에는 그 재질에 따라 Q 값 및 신호대잡음비가 다르고, 폴리에스테르의 경우를 제외하면 코팅 피복이 없는 경우와 비교하여 큰 값을 보였다. 폴리우레탄 코팅 구리선을 사용하였을 때 Q 값 및 신호대잡음비가 가장 크게 나타났으며, 가장 작은 값을 보인 폴리에스테르 코팅재질인 경우와 비교할 때 신호대잡음비가 34% 정도 큰 값을 보였다. 결론 : 1.2 mm 이하의 작은 생체시료에 적합한 솔레노이드형 RF 코일을 상용 프로브에 장착하여 사용할 수 있도록 손쉽게 제작하였으며, 폴리우레탄으로 코팅된 구리선으로 만들어진 코일의 경우 신호대잡음비가 30% 이상으로 가장 우수한 결과를 보였고, 따라서 코팅 재질의 선택이 자기공명영상의 결과에 중요하게 작용함을 확인할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.344-345
• /
• 2009

The flux-coupling type superconducting fault current limiter(SFCL) is composed of a series transformer and superconducting unit of the YBCO coated conductor. The primary and secondary coils in the transformer were wound in series each other through an iron core and the YBCO coated conductor was connected with secondary coil in parallel. In a normal condition, the flux generated from a primary coil is cancelled out by its structure and the zero resistance of the YBCO thin films. When a fault occurs, the resistance of the YBCO coated conductor was generated and the fault current was limited by the SFCL. In this paper, we investigated the fault current limiting characteristics according to turn ratio in the flux-coupling type SFCL. The experiment results that the fault current limiting characteristics was improved according to turn ratio.

• 한국전기전자재료학회논문지
• /
• 제23권9호
• /
• pp.714-717
• /
• 2010

The improved flux-lock type superconducting fault current limiter (SFCL) is composed of a series transformer and superconducting unit of the yttrium-barium-copper-oxide (YBCO) coated conductor. In this paper, we investigated current limiting characteristics through winding direction of coil 2 and variable number of coil 1 and coil 2 in improved flux-lock type SFCL. The better fault current characteristics and the burden of YBCO coated conductor can be confirmed from the experimental result in the higher turn ratio of coil 1 and coil 2 in the additive conditions. In case of subtractive condition, we can confirm a similar result in the same case of experimental conditions. but the burden of YBCO coated conductor has been increased from an increase in winding numbers of coil 2.

• 한국안전학회지
• /
• 제31권2호
• /
• pp.83-89
• /
• 2016

As the world's industrial development quickens, the highways and regional expressways have been expanding to serve the logistics and transportation needs of people. The burgeoning road construction has led to a growing interest in roadside installations. These must have reliable performance over long periods, reduced maintenance and high durability. Steel roadside barriers are prone to corrosion and other compromises to their functionality. Therefore, using high anti-corrosion steel material is now seen as a viable solution to this problem. Thus, the objective of this paper is to expand the scope of applications for high anti-corrosion steel material for roadside barriers. This paper assesses the impact safety such as structural performance, occupant protection performance and post-impact vehicular response performance by a simulation review on roadside barriers built with high strength anti-corrosion steel materials named as hot-dip zinc-aluminium-magnesium alloy-coated steel. The simulation test results for the roadside barriers built with high strength anti-corrosion steels with reduced sectional thickness meet the safety evaluation criteria, hence the proposed roadside barrier made by high strength and high anti-corrosion hot-dip zinc-aluminium-magnesium alloy-coated steel will be a good solution to serve safe impact performance as well as save maintenance cost.

• 한국전기전자재료학회논문지
• /
• 제22권8호
• /
• pp.694-697
• /
• 2009

The separated three-phase flux-coupling type superconducting fault current limiter(SFCL) is composed of a series transformer and superconducting unit of the YBCO coated conductor. The primary and secondary coils in the transformer were wound in series each other through an iron core and the YBCO coated conductor was connected with secondary coil in parallel. In this paper, we investigated the current limiting characteristics through winding number of coil 2 and winding direction in the flux-coupling type SFCL. Through the analysis, it was shown that additive polarity condition and lower winding number of coil 2 have advantaged from the point of view of fault current limiting and burned of YBCO coated conductor.

• 한국정밀공학회지
• /
• 제32권9호
• /
• pp.765-771
• /
• 2015

In an Additive Manufacturing (AM) system emplying the Powder Bed Fusion (PBF) system, polyamide-12 powder is currently recognized as the general material used. The Polyamide-12 powder's properties include an average particle size of 58 $58{\mu}m$, a density of 0.59 g/cm3, and melting point of $184^{\circ}C$, and can also be to used coat materials for metal powder. For this reason, the sintering process is similar to the polymer powder and polymer coated metal powder process, except during the post-process. The polyamide-12 powder has some disadvantages such as its high cost and the fact that it can only be used for the provided equipment from the maker. Therefore, this study aims to perform the applicability of new material, polymer and polymer coated metal, to the PBF system.