• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.6
• /
• pp.789-803
• /
• 2003

The purpose of this study is to compare the usefulness between Gaussian dispersion model and receptor model with the experimental result of the dispersion tracing of the particulate pollutants from Taean coal-fired power plants. For this purpose, the component analysis of the collected PM 10 samples was performed. In order to trace the pollution sources, factor analysis was done with the result of the component analysis. As a result of the correlativity analysis of the fifteen power plants' profiles offered by US EPA, the correlativity of No.11202 source profile showed highest rate up to 84.5%. Thus it was adopted as proper one and the contribution rate by each pollution source was calculated by Chemical Mass Balance (CMB)-8 model. The contribution rate, which was the effect rate of the power plants on each measuring point, were calculated with a range of 24∼52％ and the standard error was below 0.9 $\mu\textrm{g}$/㎥. This indicates the selection of the source profile was appropriate. Also, the concentrations of each point were calculated by the ISCST3 which is suggested by US EPA as one of the regulatory Gaussian dispersion model. The calculation result showed that the predicted concentration was 50∼58 $\mu\textrm{g}$/㎥, comparing with the measured result of 9∼65 $\mu\textrm{g}$/㎥. It was found that the concentration calculated by ISCST3 was underpredicted. It was thought that the receptor model was more favorable than the Gaussian dispersion model in estimating the effect of the particulate matter on a certain receptive point.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.73.1-73.1
• /
• 2011

석탄가스화 복합발전(IGCC) 시스템은 고온 고압으로 운전되는 가스화기에서 미분탄을 산소와 함께 가스화하여 주로 CO 및 $H_2$를 생성하고 이때 발생되는 먼지 및 황성분은 각각 집진기 및 탈황장치에서 제거되며, 석탄 회분은 고온에서 용융되어 슬래그의 형태로 배출되는 방식을 사용하고 있다. 본 연구에서는 석탄가스화 복합발전시스템 설계에 필요한 기본자료를 파악하기 위해서, 고온 고압의 운전조건에서 1일 3톤의 석탄을 처리할 수 있는 Bench Scale급 석탄가스화기를 이용하여 가스화에 사용된 원탄 및 가스화기 설비의 각 지점에서 샘플링한 고체 시료를 중심으로 열화학적 특성을 살펴보았다. 가스화 실험은 아역청탄 계열의 ABK 석탄을 대상으로 가스화기 내부의 온도와 압력을 $1400{\sim}1450^{\circ}C$, $7.5{\sim}7.6Kg/cm^2$로 유지시키면서 실시하였다. 실험에 사용된 석탄 시료의 기본적인 물성치를 조사하기 위하여 표준방법에 따라 석탄의 공업분석, 원소분석, 발열량분석 등을 실시하였다. 석탄가스화기에서 배출된 슬래그와 대상 석탄 회분의 특성을 파악하기 위해서 XRF를 이용한 회분의 성분분석, Heating Microscope를 이용한 회분의 용융점 분석, XRD를 이용한 회분과 슬래그내의 화합물의 형태 및 결정구조 파악, SEM을 이용한 슬래그의 형상 등을 분석하였다. 또한 석탄가스화기 시스템을 구성하는 각 설비의 특성을 파악하기 위해서 관련 설비의 특정 지점에서 채취한 시료의 입도분석, 원소분석, 촤 회분 무게비, 슬래그중의 잔존탄소함량, 슬래그와 슬래그로부터 제조된 용출수내의 중금속 함량분석 등을 실시하였다.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.433-440
• /
• 2020

In this study, a new type of Durometer was invented by modifying the currently used Durometer with the hemisphere shaped needle to columnar shaped needle. The aim of the study is, hence, to provide the feasibility of the advanced Durometer for assessing setting time of the concrete. Generally, the finishing of concrete surface should be conducted to secure the smooth surface, improve the permeability, and prevent the plastic shrinkage cracking. Although this surface finishing work should be conducted during the plastic phase between initial and final setting, currently in practical situations, the timing of starting the finishing work was determined by the sense of the worker. To improve this situation, Kato Junji suggested to use the hemisphere and needle shaped Durometers to determine the initial and final setting time, respectively. However, in this case, there are difficulties of using two different Durometers and of occurring failure of the Durometer due to the intruded cement paste. To prove the feasibility of new typed Durometer, setting time and surface hardness were evaluated by applying for the concrete with various replacing ratios of fly-ash and coal gasification slag as an aggregate.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.4
• /
• pp.359-366
• /
• 2022

In this paper, the effect of compression levels on the strengths of porous concrete using bottom ash aggregates was analyzed. Coal bottom ash (CBA) was used as aggregate in porous concrete in this study. The aggregate size types used in the CBA concrete mixtures were catagorized into two different ones. One included only a single aggregate particle size and the other included hybrid aggregate particles mixed at a ratio of 8:2 volume proportion. The water-binder ratio was fixed at 0.30, and the compression levels were applied at 0.5, 1.5, and 3.0 MPa valu es to fabricate a porou s concrete specimen. The total porosity, compressive, splitting tensile, and flexural tensile strengths were tested and analyzed. When the compression level increased, the total porosity decreased, meanwhile the compressive, split tensile, and flexural tensile strengths increased. The total porosity of concrete using hybrid aggregate was lower and the strength was larger than those of concrete using single-type aggregate. Finally, the correlation between the total porosity, compressive, split tensile, and flexural tensile strengths of porous concrete were presented. The total porosity and strength characteristics showed an inversely proportional correlation.

• Journal of Environmental Science International
• /
• v.25 no.12
• /
• pp.1613-1622
• /
• 2016

Zeolite (FZ), prepared from fly ash, was immobilized with polyacrylonitrile (PAN) to fabricate PAN/FZ beads. The prepared PAN/FZ beads were characterized by scanning electron microscopy, thermogravimetric analysis, and Fourier transform infrared spectroscopy. The optimum ratio to prepare PAN/FZ beads was 0.3 g of PAN to 0.3 g of FZ. The diameter of the prepared PAN/FZ beads was about 3 mm. Sr and Cu ion adsorption experiments were conducted with PAN/FZ beads. A pseudo-second-order model fit the kinetic data for Sr and Cu ion adsorption by PAN/FZ beads well. The equilibrium data fitted well with the Langmuir isotherm model, and the maximum adsorption capacities were 96.5 mg/g and 74.6 mg/g for the Sr and Cu ions, respectively. Additionally, the values of thermodynamic parameters such as Gibbs free energy (${\Delta}G^o$), enthalpy (${\Delta}H^o$) and entropy (${\Delta}S^o$) were determined. The positive values of ${\Delta}H^o$ revealed the endothermic nature of the adsorption process and the negative values of ${\Delta}G^o$ were indicative of the spontaneity of the adsorption process.

• Resources Recycling
• /
• v.25 no.3
• /
• pp.20-28
• /
• 2016

Assessment on adequate dosage of superplasticizer in eco-friendly ultra-high performance concrete (UHPC) containing industrial by-products was carried out from the standpoint of workability. Various types of industrial by-products, including blast-furnace slag, coal bottom ash and rapid-cooled electric arc furnace oxidizing slag, were utilized, and the effects of dosage of superplasticizer on the workability and strength of UHPC containing the by-products were evaluated. By utilizing the by-products, the workability of UHPC was improved and required dosage of superplasticizer was reduced. In addition, the material cost for UHPC with by-products was decreased due to reduced dosage of superplasticizer.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.24-34
• /
• 2015

Domestic companies supplying electricity must increase obligatory duty to use renewable energy annually. If not met with obligatory allotment, the electricity-supply companies must pay RPS (Renewable Portfolio Standards) penalty. Although the power plants using a pulverizing coal firing boiler could co-fire up to around 3 per cent with wood pellets mixed in with coal feedstock without any major equipment revamps, they recorded only about 60 per cent fulfillment of RPS. Consequently, USD 46 million of RPS penalty was imposed on the six power supplying subsidiaries of GENCOs in 2014. One of the solutions to reduce the RPS penalty is that the power supply companies adopt the co-firing of torrefied lignocellulosic biomass in coal plants, which may contribute to the use of over 30 per cent of torrefied biomass mixed with bituminous coals. Extra binder was required to form pellets using torrefied biomass such as wood chips, PKS (Palm Kernel Shell) and EFB (Empty Fruit Bunch). Instead of corn starch, 30, 50 and 70 per cent of Larix saw dusts were respectively added to the torrefied feedstocks such as Pinus densiflora chips, PKS and EFB. The addition of saw dusts led to the decrease of the calorific values of the pellets but the forming ability of the pelletizer was exceedingly improved. Another advantage from the addition of saw dusts stemmed from the reduction of ash contents of the pellets. Finally, it was confirmed that torrefied oil palm biomass such as PKS and EFB could be valuable feedstocks in making pellets through improved binding ability.

• Clean Technology
• /
• v.24 no.4
• /
• pp.323-331
• /
• 2018

The results of an experimental investigation on the co-firing characteristics and slagging behavior of dried and hydrothermal carbonization sewage sludge, sub-bituminous coal, and wood pellet in a fluidized bed were presented. Combustion tests were conducted in a lab-scale bubbling fluidized bed system at the uniform fuel-air equivalence ratio, air flow rate, and initial bed temperature to measure bed temperature distribution and combustion gas composition. 4 different fuel blending cases were prepared by mixing sewage sludge fuels with coal and wood pellet with the ratio of 50 : 50 by the heating value. $NO_x$ was mostly NO than $NO_2$ and measured in the range of 400 to 600 ppm in all cases. $SO_2$ was considered to be affected mostly by the sulfur content of the sewage sludge fuels. The cases of hydrothermal carbonization sewage sludge mixture showed slightly less $SO_2$ emission but higher fuel-N conversion than the dried sewage sludge mixing cases. The result of fly ash composition analysis implied that the sewage sludge fuels would increase the possibility of slagging/fouling considering the contents of alkali species, such as Na, K, P. Between the two different sewage sludge fuels, dried sewage sludge fuel was expected to have the more severe impact on slagging/fouling behavior than hydrothermal carbonization sewage sludge fuel.

• Clean Technology
• /
• v.29 no.1
• /
• pp.22-30
• /
• 2023

Mongolia is experiencing some of the world's most serious air pollution problems. The air pollution is especially severe during the winter when raw coal and low-grade fuels are used to heat homes in Ger villages. The impact of this pollution has created significant health and socioeconomic challenges for the country. In order to mitigate this air pollution, this study analyzed the fuel quality of the low-grade fuels and Mongolian waste cooking oils used in Ulaanbaatar, Mongolia. Then the environmental characteristics of traditional stove combustion and a prototype combustion heating device were compared and analyzed. In addition, the effect of replacing the heating devices was evaluated by analyzing their risks to humans. Analysis of the fuel characteristics showed that briquettes had relatively low environmental properties as a result of their high ash, N and S content. Also, after analyzing the combustion characteristics, it was found that the air quality improvement effect was higher when waste cooking oil was burned compared to the three types of coal that were analyzed. Finally, this study evaluated the impact of replacing the Mongolia traditional stove with a prototype stove that uses waste cooking oil. The results of this study are expected to help to mitigate the air quality problems currently observed in Ulaanbaatar, Mongolia.

• Journal of the Korean Ceramic Society
• /
• v.46 no.1
• /
• pp.94-101
• /
• 2009

The physical properties of artificial aggregates made from clay and inorganic wastes with poor plasticity depends largely on forming method. The artificial aggregates composing of coal fly ash, stone sludge and clay were fabricated using 4 different forming methods and those physical properties were comparatively analyzed. The surface of aggregates made through the extrusion forming process was dense and smooth but was rough for the aggregates obtained by crushing a tile-shaped green body. The aggregates made by pelletizing process had a weak green strength and bumpy surface. The shell generated at surface during a high temperature sintering process induced the most aggregates to be bloated due to a dense shell. But the aggregates made through pelletizing process with dense surface layer showed no significant change in bulk density with sintering temperatures. The water absorption of aggregates decreased with sintering temperature, and that of pelletized specimen was standing $1.8{\sim}2.2$ times higher than that of made by other forming methods. It is concluded that the aggregates having various properties could be fabricated from one batch by using different forming methods.