• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.3
• /
• pp.437-445
• /
• 2016

This paper discussed the effect of ammonia concentration adsorbed on fly ash for the ammonia emission as AAFA (Ammonia Adsorbed Fly Ash) produced from coal fired plants due to operation of NOx reduction technologies was landfilled with distilled or sea water at closed and open systems, respectively. Ammonia bisulfate and sulfates adsorbed on fly ash is highly water soluble. The pH of ammonium bisulfate and sulfate solution had significant effect on ammonia odor emission. The effect of temperature on ammonia odor emission from mixture was less than pH, the rate of ammonia emission increased with increased temperature when the pH conditions were kept at constant. Since AAFA increases the pH of solution substantially, $NH_3$ in the ash can release the ammonia order unless it is present at low concentration. $NH_4{^+}$ ion is unstable in fly ash and water mixtures of high pH at open system, which is changed to nitrite or nitrate and then released as ammonia gas. The proper conditions for < 20 ppm of ammonia concentration released from the AAFAs landfilled in ash pond were explored using an open system with sea water. It was therefore proposed that optimal operation to collect AAFA of less than 168 ppm ammonia at the electrostatic precipitator were controlled to ammonia slip with less than 5 ppm at SCR/SNCR installations, and, ammonia odor released from mixture of fly ash of 168 ppm ammonia with sea water under open system has about 20 ppm.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.28 no.2
• /
• pp.49-57
• /
• 2020

Due to the sewage sludge's characteristics of high water content and low calorific value, it is hard to use sewage sludge as an energy source. In this study, we investigated production of bio-solid fuel which is mixed both sewage sludge and woody biomass in order to improve the sewage sludge's characteristics and replace fossil fuels. A thermogravimetric analysis was used to investigate the co-combustion characteristics of the mixed coal and bio-solid fuel of 5%, 10%, 15%, respectively. The analysis was carried out under non-isothermal conditions by raising the internal temperature of 25℃ to 900℃ with an increment of 10℃/min. In the case of comparing single coal sample and mixture sample of coal and bio-solid fuel, the initiation combustion temperature has slightly changed. However, both the maximum combustion temperature and the termination start combustion temperature were hardly noticeable. The initiation combustion was occurred between 200~315℃ and the thermal decomposition causing a significant weight change occurred between 350~700℃. As a result of the kinetic analysis of the co-combustion, the activation energy was decreased as the mixing rate was higher. Therefore, it is able to co-combust the mixed coal and bio-solid fuel in power plants.

• 연구논문집
• /
• s.23
• /
• pp.93-107
• /
• 1993

The chemistry and performance characteristics of the EBDS process have been introduced, in which experimental results from laboratory, test plant, and pilot plant studies agree very well and can be understood from detailed kinetic models. The parametric dependencies of the NOx and $SO_2$, removal yields on the input conditions have been discussed and formulated quantitatively. The process is best suited for flue gas with high $SO_2$, loadings. The operation conditions, such as dose, ammonia, and water additions, can be adjusted fast upon load changes. The process works waste water free and the major product is a mixture of ammonium nitrate and sulfate that can be used as fertilizer. The up-date results show that the EBDS technology is safe and competitive with other already well-established technologies. Due to these interesting features, the electron beam process has gained much international recognition. Demonstration units of 100MW have been proposed in the United States and Japan. Further pilot plants are under construction in Poland and China, countries that make abundant use of highsulfur coal. Additional research activities are under way to further improve the energy efficiency of process, and accelerator prices have been decreasing during the past 10 years. So the EBDS process has a good chance to start a new generation of emission-control technology.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.3
• /
• pp.173-179
• /
• 2014

This is an experimental study for recycling coal ash left over from coal use as a potential fine aggregate in concrete. Coal ash is generally divided into either fly ash or bottom ash. Fly ash has been utilized as a substitution material for cement in concrete mixes. On the other hand, bottom ash has the problem of low recycling rates, and thus it has been primarily reclaimed. This study partially substituted fine concrete aggregates with bottom ash to increase its application rate and therefore its recycling rate; its suitability for this purpose was confirmed. The concrete's workability dropped noticeably with increasing bottom ash content when a fixed water-cement ratio of concrete mix was used. Thus, concrete mixes with higher ratio levels are required. To address this problem, concrete was mixed using a polycarboxylate high-range water reducing agent. The fluidity and air entrainment immediately after mixing the concrete and 1 h after mixing were measured, thereby replicating the time concrete is placed in the field when produced either in a ready-mixed concrete or in a batch plant. As a result of this research, the workability and air entrainment were maintained 1 h after mixing for a concrete mixture with approximately 30% of its fine concrete aggregates substituted with the bottom ash. A slight drop in compression strength was seen; however, this confirmed that potential of using bottom ash as a fine aggregate in concrete.

• Journal of Aquaculture
• /
• v.9 no.3
• /
• pp.239-245
• /
• 1996

As one of the red tide control method, montmorillonite was used to eliminate the causative organisms in Korea and Japan. We assayed the loess to replace the montmorillonite because it distribute in large quantity and nearby the red tide occurrence in South Coast of Korea. By using the mixture of loess and coal ashes, we examined the decreasing level of nutrients such as ammonia and phosphate, the elimination of causative organisms as a chlorophyll a content, and the harmful effect on aquaculture orgarnisms in cage culture farms. Half of the ammonium and phosphate was adsorbed by the loess particles, but only $25\%$ of ammonium was adsorbed by the coal ashes particles. In water column test, the particles of loess and coal ashes were settled down by $80\%$ in 20 minutes, the red tide organisms was eliminated by $80\%$ after 2 hours in 1,000 ppm of loess suspension, but the organisms were eliminated only $30\%$ by the same concentration of coal ashes. The harmful test of fishes and invertbrates, we observed any other negative effects of test animals than a tint deceleration in yellowtail.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.180-188
• /
• 2020

To replace Japanese coal ash used in the domestic cement production and to recycle large quantities of domestic pond ash, it is essential to develop the technologies for quality control of cement by using the domestic pond ash. Thus, in this study, the feasibility of using the pond ash as a raw material for cement was investigated through chemical composition and microstructure analysis. As a result, most of the domestic pond ash contained slightly more Fe2O3, chloride, and unburned carbon contents than Japanese coal ash. In particular, the contents of chloride were considerably low in the pond ash that was transferred to fresh water or collected from surface of landfill area. However, since circulating fluidized bed boiler coal ash had relatively high SO3 contents causing durability problems of cement, it was not suitable for use as a raw material for cement. Thus, to replace Japanese coal ash with the domestic pond ash, it is necessary to introduce the adjustment of mixture proportion of cement raw materials and the process of removing chloride in the pond ash.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.402-410
• /
• 2000

As the combustion process of CWM consists of the water evaporation, the release and combustion of volatile matter, and the combustion of char for every particle, it is more complex than that of existent liquid fuel. Though the many studies on CWM combustion have been carried out by the single droplet using hanging methods or the multiple droplet using atomization methods, any report don't presents definite solution about the effects by the initial water evaporation and combustion of volatile. When CWM is suddenly exposed in the high temperature surroundings, the internal water evaporates and then each droplet builds up pores. Besides, porosity rate changes along the temperature of surroundings, the composition ratio of CWM, and the initial diameter of droplet. In result, because it affects the whole combustion rate, the combustion of CWM has complex mechanism as compared with the combustion of liquid or gas fuel. Therefore, concentrating on porous structure of CWM, this study has proceeded to acquire the basic data on the CWM injection combustion and closely examines the effects of the first stage combustion on the whole combustion by measuring the diameter variations, pore rate, mass fraction burned, and the internal temperature changes of CWM droplet. The results demonstrate that $60{\sim}70%$ of initial mass is reduced during water evaporation and volatile combustion period, and swelling rate, mass faction burned, and density variation are greatly concerned with atomization of CWM etc.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.5
• /
• pp.401-410
• /
• 2002

Concerns for energy conservation, environmental pollution, and the fact that organic wastes account for a major portion of our waste materials, have created the interest of biogas, which usually contains about 60 to 70 percent methane, 30 to 40 percent carbon dioxide, and other gases, including ammonia, hydrogen sulfide, mercaptans and other noxious gases. Cyclone combustors are used for homing a wide range of fuels such as low calorific value gas, waste water, sludge. coal, etc. The 3-dimensional swirling flow, combustion and emission in a tangential inlet cyclone incinerator under different inlet conditions are simulated using a standard k-s turbulence model and ESCRS (Extended Simple Chemically-Reacting System) model. The commercial code Phoenics Ver.3.4 was used for the present work. The main parameters considered in this work are inlet velocity and air to fuel ratio. The results showed that the change of operating conditions had an influence on the shape and size of recirculation zones, mixture fraction and axial velocity which are important factors for combustion efficiency and emission behavior. The application of this kind of computer program seams to be promising as a potential tool for the optimum design of a cyclone combustor with low emission.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2953-2961
• /
• 2008

습식 석탄가스화란 석탄을 물과 혼합한 슬러리 형태(CWM, Coal Water Mixture)로 사용하는 것을 말하며, 분류층 가스화기에 빠르게 적용되었던 이유는 석유류 가스화와 공급방식이 유사하다는 점에서 출발하였다고 볼 수 있다. 1950년도에 사용되어 왔던 석유류 가스화 이용은 1970년 이후로는 유가 상승의 영향으로 석탄가스화로 바뀌게 되었다. 합성가스의 활용공정인 화학물질 제조 또는 복합발전의 운전 압력이 대부분 높기 때문에 가스화 압력을 높게 유지하기 위하여 슬러리 공급 방식이 많이 이용되었다. 슬러리 형태의 석탄 연료는 석유류가스와 시스템을 유사하게 활용할 수 있는 장점이 있으며, 특별히 고압을 필요로 하는 경우에도 비교적 간단한 시스템을 이용하여 공급 가능하다. 본 고에서는 현재까지 한국에너지기술연구원에서 수행된 습식 석탄가스화 기술개발 내용에 대하여 기술하고자 하였다.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.73-82
• /
• 2011

Coal ash of industial by-products was not recycled about 30% in total emissions. Moreover, it caused environmental pollution as well as wasted unnecessary expenses and time. Currently, fly ash(FA) is recycled as construction material however ponded ash(PA) is mostly buried. Lightweight foamed Controlled Low-Strength Materials(CLSM) evaluated in this study reduces unit weight by mixing foam in the traditional Controlled Low-Strength Material and has lightweight and flowability to be available for backfill materials in construction. Flow test, unconfined compressive strength test, and foamed-slurry unit weight test were performed in this study and the applicability of lightweight foamed CLSM for construction materials was evaluated. The results indicate that the mixture ratio(PA:FA) ranging from 70:30 to 50:50, cement of 7%, foam of 2~3%, and water content of 26.5~29.5% were required to satisfy the following standards such as flow value(i.e., 20cm), unconfined compressive strength(i.e., 0.8~1.2MPa), and foamed-slurry unit weight(i.e., $12{\sim}15kN/m^3$).