• 한국자기학회지
• /
• 제15권2호
• /
• pp.109-112
• /
• 2005

Electronic and magnetic properties of $Ti_{1-x}M_xO_{2-\delta}$ (M=Co and Fe) thin films grown by sol-gel method have been investigated. Anatase and rutile $Ti_{1-x}Co_xO_{2-\delta}$ films were successfully grown on $Al_2O_3$ (0001) substrates and exhibited p-type electrical conductivity while the undoped films n-type conductivity. Room temperature vibrating sample magnetometry measurements on the anatase and rutile $Ti_{1-x}Co_xO_{2-\delta}$ films with same x ($=4.8 at.{\%}$) showed quite similar magnetic hysteresis curves with the saturation magnetic moment of $\~4 {\mu}_B$ per Co ion despite their differences in structural and electronic properties. Such giant magnetic moment is attributable to the unquenched orbital moment of the $Co^{2+}$ ions substituting the octahedral $Ti^{4+}$ sites. Similar ferromagnetic behavior was observed for $Ti_{1-x}Fe_xO_{2-\delta}$ films that are highly resistive compared to the Co doped samples. Saturation magnetic moment was found to decrease for higher x, i.e., $\~2$ and $\~1.5 {\mu}_B$ per Fe ion for x=2.4 and 5.8 at. $\%$, respectively. Conversion electron $M\ddot{o}ssbauer$ spectroscopy measurements predicted the coexistence of $Fe^{2+}$ and $Fe^{3+}$ ions at the octahedral sites of $Ti_{1-x}Fe_xO_{2-\delta}$.

• 대한치과보철학회지
• /
• 제45권6호
• /
• pp.805-814
• /
• 2007

Statement of problem. Composite resin-veneered metal restorations can be used as an alternative to porcelain-fused-metal restorations. But, because of the relatively low bond strength of veneering composite to metal framework, various surface treatment methods have been introduced to improve the bond strength. Purpose. The object of this study was to compare the shear bond strength of different combinations of each of the two bonding systems and each of the two composite veneering resins to cp-Ti/Co-Cr alloy. Material and methods. Two resin bonding systems (metal conditioner containing MEPS monomer, tribochemical silicoating system) and two composite resins (Gradia, Sinfony) were tested on cp-Ti and Co-Cr alloy. Then, according to manufacturers' instructions, resin bonding systems and composite resins were applied. All test specimens were divided into four groups for each alloy; I) sandblast + Metal Primer II + Gradia (MG), II) sandblast + Metal Primer II + Sinfony (MS), III) Rocatec + Gradia (RG), IV) Rocatec + Sinfony (RS). The shear bond strength was determined using a universal testing machine and all data were statistically analyzed with Mann-Whitney test and Kruskal-Wallis test at the significance level of 0.05. Results. The mean (standard deviations) of shear bond strength according to the combinations of two bonding systems and two composite resins to cp-Ti arranged from 16.44 MPa to 17.07 MPa and the shear bond strength to Co-Cr alloy ranged from 16.26 MPa to 17.70 MPa. The result shows that the difference were not statistically significant. Conclusion. The shear bond strengths of composite resins to both cast cp-Ti and Co-Cr alloy were not significantly different between the metal conditioner and the tribochemical silicoating system. And no differences in bond strength were found between cp-Ti and Co-Cr alloy.

• 한국재료학회지
• /
• 제13권11호
• /
• pp.711-716
• /
• 2003

Gate length, height, and silicide thickness have all been shrinking linearly as device density has progressively increased over the years. We investigated the effect of the cobalt diffusion during the silicide formation process on the 60$\AA$-thick gate oxide lying underneath the Ti/Co and Co/Ti bilayers. We prepared four different cobalt silicides, which have similar sheet resistance, made from the film structure of Co/Ti(interlayer), and Ti(capping layer)/Co, and peformed the current-voltage, time-to-break down, and capacitance-voltage measurements. Our result revealed that the cobalt silicide process without the Ti capping layer allowed cobalt atoms to diffuse into the upper interface of gate oxides. We propose that 100$\AA$-thick titanium interlayer may lessen the diffusion of cobalt to gate oxides in 1500-$\AA$ height polysilicon gates.

• 전기화학회지
• /
• 제12권3호
• /
• pp.282-286
• /
• 2009

MWNT(CNTs)를 지지체로 촉매를 합성하고 특성평가를 진행하였다. $Pt/Au/TiO_2$는 CNTs(cabon 나노 튜브) 탄소 지지체에 첨가되어 직접 메탄올 연료 전지의 성능을 개선하였다. XRD와 SEM을 통해 아나타제 $TiO_2$와 Pt/Au를 확인하였고 각각의 입자 사이즈는 200 nm와 20${\sim}$25 nm 이다. 혼성 촉매의 활성은 CV를 통해 측정되었으며 제조된 촉매는 연료전지 이용에 유망하다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.213-213
• /
• 2011

Gold catalysts supported on TiO2 have shown a unique catalytic behavior on CO oxidation, depending on surface effects. Particle size has an influence on the surface activity. To make monodisperse Au nanoparticles, organic capping ligands, such as alkylthiols, were used by a "greener" synthesis method [1,2] and Au nanoparticles were deposited on TiO2. However, organic capping ligands must be removed for high catalytic activities by the Au nanoparticles without changing the Au size [3]. We used UV ozone treatment to decompose thiol ligands. The samples have been characterized by X-ray photoelectron spectroscopy to examine the surface modification by UV ozone treatment. We show the size distribution of the gold nanoparticles by light scattering analysis and transmission electron microscopy. Au/TiO2 have been prepared using the wetness impregnation method. The catalytic performance of CO oxidation over Au supported on TiO2 under oxidizing reaction conditions (40 Torr CO and 100 Torr O2) were tested. The results show that the catalytic activity depends on particle size and the time of UV ozone exposure, which suggests the role of sulfur bonding in determining the catalytic activity of Au/TiO2 catalysts.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.165-170
• /
• 2004

Growth behavior of two different types of grains, faceted and rounded, in a liquid matrix has been studied in the (75WC-25TiCN)-30Co system. Powder samples were sintered above the eutectic temperature for various times under a carbon saturated condition. (Ti,W)(C,N) grains with a rounded shape and WC grains with a faceted shape coexisted in the same Co based liquid. With increasing sintering time, the average size of (Ti.W)(C,N) grains increased continuously and very large WC grains appeared. The growth of rounded (Ti,W)(C,N) grains followed a cubic law, r^3-r^3_0$=kt, where r is the average size of the grains, $r_0$ the initial average size, k the proportionality constant and t the sintering time. indicating a diffusion-controlled growth. On the other hand, the growth of the faceted WC grains resulted in a bimodal grain size distribution, showing an abnormal grain growth. These observations show that the growth behavior of different types of grains is governed by their shape, faceted or rounded, even in the same liquid matrix.

• 한국환경과학회지
• /
• 제28권1호
• /
• pp.65-73
• /
• 2019

The catalytic activity of Ni-0.2%YSZ (Yttria-Stabilized Zirconia) with different promoters was evaluated for $CO_2$ methanation. The catalysts were weighed for mixing and they were dried at $110^{\circ}C$ for molding into disks. The concentration of $CO_2$ and $CH_4$ for conducting of $CO_2$ methanation were analyzed by gas chromatography and the physical characteristics of the disk-type catalyst formed were analyzed by X-ray diffraction, scanning electron microscope and energy dispersive x-ray spectrometer. The addition of $CeO_2$ as a promoter for Ni-0.2%YSZ (denoted as Ni-5%Ce-0.2%YSZ) resulted in the highest $CO_2$ methanation. It also showed catalytic activity at a low temperature($200^{\circ}C$). Following this, $ZrO_2$, $SiO_2$, $Al_2O_3$ and $TiO_2$ were added to Ni-5%Ce-0.2%YSZ to compare the $CO_2$ methanation, and the highest efficiency was found for. Ni-1%Ti-5%Ce-0.2%YSZ Then, the concentration of Ti was increased to 10% and the catalytic activity was estimated using seven different types of commercial $TiO_2$. In conclusion, ST-01 $TiO_2$ showed the highest efficiency for $CO_2$ methanation.

• 한국자기학회지
• /
• 제18권3호
• /
• pp.109-114
• /
• 2008

Solid State Reaction법으로 $Ti_{0.96}Co_{0.02}Fe_{0.02}O_2$ 시료를 제조하였다. 각각의 시료를 $870^{\circ}C$, $900^{\circ}C$, $930^{\circ}C$로 24시간 열처리하였다. 이 때 Ti-getter의 유무를 통해 각각의 온도에서 Ti-getter에 따라 시료의 특성이 어떻게 변화하는지 관찰하고자 한다. 제작된 시료의 구조분석을 위해 시료의 분말 회절실험을 실시하였다. VSM을 이용하여 시료의 자성을 측정하고, 금속이온의 형태와 시료 내에서 cluster로 존재하는지 여부를 조사하기 위해 TEM과 SEM, EDS실험을 하였다. XRD pattern 분석결과, 결정구조는 tetragonal구조로써, 순수한 Rutil-$TiO_2$상이 주를 이루며, 2차상으로는 getter가 없을 때는 $Fe_2TiO_5$, 있을 때는 Fe가 관측되었다. 시료의 자성을 측정한 결과, getter가 없을 때는 $870^{\circ}C$일 때 자화값은 약 $0.025{\mu}B$/CoFe 정도로 강자성을 보이지만, $900^{\circ}C$와 $930^{\circ}C$에서는 강자성을 보이지 않는다. Ti-getter가 있을 때의 자화값은 $870^{\circ}C$에서는 약 $1.1\;{\mu}B$/CoFe, $900^{\circ}C$와 $930^{\circ}C$일 때는 $1.5\;{\mu}B$/CoFe 정도로 강자성을 보인다. 이러한 자성의 차이는 Ti-getter의 유무에 따른 2차상의 차이로 결정된 것으로 보인다. Titanium이 고온에서 산소와 질소, 공기 속의 수분과 쉽게 결합하는 성질을 가지고 있기 때문에 이것을 이용하면 좀 더 낮은 산소분압을 얻을 수 있다. 시료의 산소분압에 따라 자화값이나 원자 구조의 변화에 상당한 영향을 받게 되어 시료의 특성이 다르게 나타나는 것을 확인 할 수 있다. TEM과 SEM, EDS실험결과에서는 Co와 Fe가 골고루 분포하는 영역이 있는가 하면 Ti만 관측되는 부분도 존재했다. 시료의 Co와 Fe가 시료전체에 골고루 퍼져있는 것이 아니라 부분적으로 분포하고 있음을 확인 할 수 있다.

• 한국재료학회지
• /
• 제7권12호
• /
• pp.1058-1062
• /
• 1997

강유전체 전계효과를 관찰하기 위해 LaCoO$_{3}$/Pb(Zr, Ti)O$_{3}$(La, Sr)CoO$_{3}$ 다층구조를 LcOo$_{3}$가 기판 위에 pulsed laser deposition(PLD)법으로 에피택셜하게 성장시켰다. 이러한 다층구조에서는 전도성 채널층으로 Si대신 반도성 LaCoO$_{3}$가 사용 되었다. LaCoO$_{3}$(LCO)의 비저항은 산소 분위기에 의하여 변화되었는데 특히 증착시 산소 분위기에 의존함을 보였다. LCO의 비저항은 0.1-100Ωcm범위에서 변화되었다. LCO층에 유도되는 강유전체 전계효과는 Pb(Zr, Ti)O$_{3}$(PZT)의 분극 상태에 따른 LCO의 저항 변화를 측정함으로써 관찰되었는데 1020$\AA$ 두께를 가진 LCO층에서는 4%의 저항 변화를 얻었으며 680$\AA$의 LCO에서는 9%의 증가된 저항 변화를 얻었다. DC 바이어스(-5V)를 가한 후에는 저항 변화가 45%까지 증가하였다. 이러한 결과는 적당한 비저항을 갖는 LCO를 사용한 LCO/PZT/LSCO다층구조가 강유전체 전계효과 트랜지스터로 사용될 수 있다는 가능성을 제시하고 있다.

• 대한치과보철학회지
• /
• 제44권5호
• /
• pp.628-641
• /
• 2006

Statement of problem: Dental magnetic materials have been applied to removable prosthetic appliances, maxillofacial prostheses, obturator and dental implant but they still have some problems such as low corrosion resistance in oral environments. Purpose: To increase the corrosion resistance of dental magnetic materials, surfaces of Sm-Co and Nd-Fe-B based magnetic materials were plated with TiN and sealed with stainless steels. Materials and methods : Surfaces of Sm-Co and Nd-Fe-B based magnetic materials were plated with TiN and sealed with stainless steels, and then three kinds of electrochemical corrosion test were performed in 0.9% NaCl solution; potentiodynamic, potentiostatic, and electrochemical impedance test. From this study, corrosion behavior, amount of elements released, mean average surface roughness values, the changing of retention force, and magnetic force values were measured comparing with control group of non-coated magnetic materials. Results: The values of surface roughness of TiN coated Sm-Co and TiN coated Nd-Fe-B based magnetic materials were lower than those of non coated Sm-Co and Nd-Fe-B alloy. From results of potentiodynamic test, the passive current density of TiN coated Sm-Co alloy were smaller than those of TiN coated Nd-Fe-B alloy and non coated alloys in 0.9% NaCl solution. From results of potentiostatic and electrochemical impedance test, the surface stability of the TiN coated Sm-Co alloy was more drastically increased than that of the TiN coated Nd-Fe-B alloy and non-coated alloy. The retention and magnetic force after and before corrosion test did not change in the case of TiN coated magnetic alloy sealed with stainless steel. Conclusion: It is considered that the corrosion problem and improvement for surface stability of dental magnetic materials could be solved by ion plating with TiN on the surface of dental magnetic materials and by sealing with stainless steels.