• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1432-1433
• /
• 2006

$Li_{2}CO_3$ doped $Ba_{0.5}Sr_{0.5}TiO_3$ ceramics were fabrication by sol-gel method. Sintering temperature must be suited to the LTCC technology. Structure and dielectric properties were investigated for effect of $Li_{2}CO_3$ dopants at BST. Structure of $Li_{2}CO_3$ doped $Ba_{0.5}Sr_{0.5}TiO_3$ ceramics were dense and homogeneous with almost no pore. Relative permittivity was decreased and dielectric loss was increased with increasing $Li_{2}CO_3$ doping rations. In the case of the 3wt% $Li_{2}CO_3$ doped $Ba_{0.5}Sr_{0.5}TiO_3$ ceramics sintered at $900^{\circ}C$, relative permittivity and dielectric loss were 907 and 0.003 at 100 kHz.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.937-939
• /
• 2007

Carbon nanotubes (CNTs) have used as an electron field emitter of the field emission display (FED) due to their characteristics of high-electron emission, rapid response and low power consumption. However, to commercialize the FED with CNT emitter, some fundamental problems regarding life time and emission efficiency have to be solved. In this study, we investigated the $TiO_2$ coated CNT as a field emitter. $TiO_2$ nanoparticles can coated on CNT surface by chemical solution method. $TiO_2$ nanoparticles had uniform size with the average size of about 2.4 nm to 3.1 nm. Field emission performance of CNT coated with $TiO_2$ nanoparticles was evaluated and discussed.

• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.178-184
• /
• 2018

In the present study, $TiB_2-Co$ composite coatings were thermally sprayed onto the surface of a 304 stainless steel substrate using an atmospheric plasma spray (APS). The phase analysis of the powders and plasma-sprayed coatings was performed using X-ray diffractometry analysis. The microstructures of the coatings were studied by a scanning electron microscope (SEM). The average particle size and flowability of the feedstocks were also measured. Both $TiB_2-32Co$ and $TiB_2-45Co$ (wt.%) coatings possessed typical dense lamellar structures and high-quality adhesion to the substrate. The oxidation behaviors of the coatings were studied at $900^{\circ}C$ in an atmospheric environment. In addition, the cross-sectional images of the oxidized coatings were analyzed by SEM. A thin and well-adhered layer was formed on the surface of both $TiB_2-Co$ coatings, confirming satisfactory high-temperature oxidation resistance. The kinetic curves corresponding to the isothermal oxidation of the coatings illustrated a short transient stage from rapid to slow oxidation during the early portion of the oxidation experiment.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.1
• /
• pp.80-84
• /
• 2008

We systematically investigated the resistive switching properties of thin $TiO_2$ films on Pt/Ti/$SiO_2$/Si substrates that were embedded with a Co ultra thin layer. An in-situ sputtering technique was used to grow both films without breaking the chamber vacuum. A stable bipolar switching in the current-voltage curve was clearly observed in $TiO_2$ films with an embedded Co ultra thin layer, addressing the high and low resistive state under a bias voltage sweep. We propose that the underlying origin involved in the bipolar switching may be attributed to the interface redox reaction between the Co and $TiO_2$ layers. The improved reproducible switching properties of our novel structures under forward and reverse bias stresses demonstrated the possibility of future non-volatile memory elements in a simple capacitive-like structure.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.310-316
• /
• 2012

Nanocrystalline $BaTiO_3$ powder could be synthesized by solid-state reaction using the mixture which was prepared by a high energy milling process in a bead mill for $BaCO_3$ and nanocrystalline $TiO_2$ powders mixture. Effect of the milling time on the powder characteristic of the synthesized $BaTiO_3$ powder was investigated. Nanocrystalline $BaTiO_3$ with a particle size of 50 nm was obtained at $800^{\circ}C$. High tetragonal $BaTiO_3$ powder with a tetragonality(=c/a) of 1.009 and a specific surface area of $7.6m^2/g$ was acquired after heat-treatment at $950^{\circ}C$ for 2 h. High energy ball milling was effective in decreasing the reaction temperature and increasing the tetragonality.

• Korean Journal of Organic Agriculture
• /
• v.20 no.3
• /
• pp.385-397
• /
• 2012

A pot experiment was carried out to examined the effect of electrolyzed micronutrients (Fe, Mn, Zn, Sr, Se, Sn, Co, Ti, and V) solution treatments with nutrient solution and SCB slurry on the mineral content and growth of tomato in cherry tomato (Lycopersicon esculentum). The treatment of nutrient solution (NS)+micronutrients solution (MS) significantly increased the concentrations of Li, Zn, Sr, Se, Ti as compared with that of NS alone in the cherry tomato fruits, and SCB+MS solution treatment significantly increased Li, Zn, Se, Co, Sr, and Ti contents as compared with SCB treatment. The micronutrient contents of MN+SCB+MS treatment were significantly higher in Li, Zn, Se, Co and in Ti than those of SCB and NS treatment, respectively. The growth and yield of cherry tomato fruits was highest with NS treatment. The yield indices of cherry tomato treated with NS+MS treatment and SCB+NS+MS were 97% and 94% of NS treatment. In conclusion, it seems to be possible to produce micronutrient-fortified cherry tomato by the mixed treatment of electrolyzed micronutrients.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.284-287
• /
• 2002

The $BaTi_{4}O_{9}$ ceramics with CoO(0.5wt%) were prepared by the conventional mixed oxide method. The sintering temperature and time were $1350^{\circ}C$, 3hr., respectively. The structural properties were investigated with sintering temperature by XRD. Also the microwave dielectric properties of the $BaTi_{4}O_{9}$ ceramics were studied. According to the X -ray diffraction patte구 of the $BaTi_{4}O_{9}$ ceramics with CoO(0.5wt%), the orthorhombic $BaTi_{4}O_{9}$ structure was appeared. In the case of $BaTi_{4}O_{9}$ ceramics with CoO(0.5wt%), dielectric constant $(\varepsilon_{r})$, quality factor$(Q{\times}f_r)$ and temperature coefficient of resonant frequency$(\tau_{f})$ were 40.8, 43,270 and $2.5ppm/^{\circ}C$, respectively.ࠀࠀ Ѐ耀
Āࠀ 耀耀  ࠀက@ĀĀȀ
ЀĀကЀကࠀ耀Ȁ@ࠀ
Ѐ
Ѐ€Ȁ耀
 @䀀က 䀀Ѐ€耀 Ȁ @ ࠀЀЀကȀȀЀ Āက蠀

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.297-297
• /
• 2007

The $(B_{0.5},Sr_{0.5})TiO_3$ ceramics, which added with low sintering materials $Li_2CO_3$ and ZnBO, was investigated for LTCC(low temperature co-fired ceramic) applications. To compare sintering temperature of $(B_{0.5},Sr_{0.5})TiO_3$ respectively, we added 1, 2, 3, 4, and 5wt% of $Li_2CO_3$ and ZnBO to $(B_{0.5},Sr_{0.5})TiO_3$. For confirming the sintering temperature, the respective specimens were sintered from $750^{\circ}C$ to $1200^{\circ}C$ by $50^{\circ}C$. The case of $Li_2CO_3$ greatly lowered the sintering temperature of $(B_{0.5},Sr_{0.5})TiO_3$ ($1350^{\circ}C$) below $900^{\circ}C$. The addition of ZnBO improved the loss tangent of $(B_{0.5},Sr_{0.5})TiO_3$. The crystalline structure of $LiCO_3$ doped $(B_{0.5},Sr_{0.5})TiO_3$ and ZnBO doped $(B_{0.5},Sr_{0.5})TiO_3$ was analyzed with the X-ray diffraction (XRD) analysis. The dielectric permittivity and loss tangent of $Li_2CO_3$ doped BST and ZnBO doped BST were measured with the HP 4284A precision. From the electrical characterization, we respectively obtained the dielectric permittivity 1361, loss tangent $6.94{\times}10^{-3}$ at $Li_2CO_3$ doped $(B_{0.5},Sr_{0.5})TiO_3$ (3wt%) and the dielectric constant 1180, loss tangent $3.70{\times}10^{-3}$ at ZnBO doped $(B_{0.5},Sr_{0.5})TiO_3$(5wt%).

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.84-89
• /
• 2012

Attempts were made to develop a stable gray pigment at reducing atmosphere, substituting Ti in $ZrTiO_4$ with Mn, Fe, Co and Cu The pigment synthesized at $1300~1500^{\circ}C$ by solid state method with the composition of $ZrTi_{1-x-y}A_xB_yO_4$ (x = y = 0.005, 0.015, 0.035, 0.055, 0.075, 0.095, 0.115, 0.135, 0.155, 0.175 and 0.195 mole, A = Mn(III), Fe(III), Co(II, III) and Cu(II) (chromophores), B = Sb (counterion). The pigments were fired at $1400^{\circ}C$ for 3 h with substitute amount changes of Mn, Fe, Co and Cu to $ZrTiO_4$ crystals, and analyzed by Raman spectroscopy to figure out substitute limits. Results indicated 0.035 mole for Mn, 0.115 mole for Fe, 0.015 mole for Co and 0.015 mole for Cu as substitute limits, respectively. Figs. 1, 2, 3, and 4 represent each substitute pigments of Mn, Fe, Co and Cu. Synthesized pigment was applied to a lime and a lime-magnesia glaze at 7 wt% each, and fired at reducing atmosphere of $1240^{\circ}C$, soaking time 1h. Gray color was obtained with CIE-$L^*a^*b^*$ values at 44.55, -0.65, 1.19(Mn), 40.36, -0.90, 0.30(Fe), 42.63, -0.03, -1.49(Cu) and -40.79, -0.28, -0.91(Co), respectively.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.62-68
• /
• 2003

Ba-ferrite particles added with Co and Ti, which were known well the additives for the control in coercivity, were synthesized by sol-gel method. In the range 90 to 120 minute reaction time, a stable sol solution which showed no change with temperature, pH, viscosity and aging time. After dried and heat treatment of sol solution, Ba-ferrite phase formed at $700^{\circ}C$ with Differential Thermal Analysis(DTA) and X-Ray Diffractometer(XRD) measurement. The crystallinity became to be better with increasing the temperature. It were showed by Scanning Electron Microscopy(SEM) that Ba-ferrite increased to particle sizes as increasing heating temperature and obtained of narrow particles size distribution. Also, magnetic characteristics of Ba-ferrite powders Co and Ti added were observed by a Vibrating Sample Magnetometer(VSM). Saturation magnetization$(M_s)$ was not much changed, however. the coercivity$(H_c)$dramatically dropped with addition of Co and Ti.