• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1580-1587
• /
• 2005

To calculate the long-term allowable strength of geosynthetic reinforcement, replacement method was recommended. The isochronous creep curve by S. Turner was used to define the relation between creep strain and allowable strength. In isochronous curve at given time, one can read the allowable strength at allowable creep strain. The allowable strain gets from specification by directors or manufacturers according to the allowable displacement of reinforced structures. The allowable strength can be determined in relation to the allowable horizontal displacement each structures case by case. The effect of install damage on isochronous behaviors of geosynthetic reinforcement was little. In previous study, install damage increase the creep strain slightly. And the degradation was not identified. But it is supposed that degradation increase the creep strain. In conclusion, The recommended model to determine long-term allowable strength of geosynthetic reinforcements considering tensile deformation of reinforcement and soil is fit for proper, correct and economic design for reinforced earth walls.

• Advances in materials Research
• /
• v.5 no.2
• /
• pp.121-130
• /
• 2016

In an attempt to reach a balance of performances in homo-polypropylene based system, the effects of single and hybrid reinforcements inclusions comprising calcium carbonate nanoparticles (2, 4 and 6 phc) and glass fibers (10 wt.%) on the mechanical and thermal properties were investigated. Different samples were prepared by employing twin-screw extruder and injection molding machine. In morphological studies, the uniform distribution of glass fibers in PP matrix, relative adhesion between glass fibers and polymer, and existence of nanoparticles in polymer matrix were observed. $PP/CaCO_3$ (6 phc) as compared to pure PP and PP/GF had superior tensile and flexural strengths, impact resistance and deformation temperature under load (DTUL). $PP/GF/CaCO_3$ (6 phc) composite displayed comparable tensile and flexural strengths and impact resistance to neat PP, while its tensile and flexural moduli and deformation temperature under load (DTUL) were 436%, 99% and $26^{\circ}C$greater respectively. The maximum impact resistance was observed in $PP/CaCO_3$(6 phc). The highest DTUL was perceived in PP hybrid nanocomposite containing 10 wt.% glass fiber and 4 phc $CaCO_3$ nanoparticle.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.604-610
• /
• 2006

Common structural rules of JBP(Joint Bulker Project) and JTP(Joint Tanker Project), which will come into effect in 2006, invoke the necessity of the ultimate limit state(ULS) design for ship structures. Even though the many applications of ULS analysis have been performed for ship structures, there have few studies carried out for deck machineries and their supporting structures. Recently four major Korean shipbuilders(DSME, HHI, HHIC, SHI) jointly developed and proposed a new design standards for mooring fittings and also proposed the SWL (Safety Working Load) obtained based on the first yield criterion. In this study, various ultimate strength analyses were performed for bollards and their foundation structures whose yield strengths were quantified by the research consortium. Prior to performing the ultimate strength analyses, the numerical calculation method was substantiated with the test results provided in the joint work report. Based upon the results of this study, it can be concluded that the reinforcements to increase the yield strength are not always resulted in the enhancement of the ultimate strength. Furthermore, the additional production costs for the reinforcements can not be rewarded by the ultimate strength. Therefore, another alternative arrangements should be developed in the view point of ultimate strength.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.1
• /
• pp.35-39
• /
• 2008

This experimental study examines the applicability of polymer mortar permanent forms using a methyl methacrylate (MMA) solution of waste expanded polystyrene (EPS) to develop effective recycling processes for the EPS, referring to the flexural behavior of a polymer-impregnated mortar permanent form with almost the same performance as commercial products. An MMA solution of EPS is prepared by dissolving EPS in MMA, and unreinforced and steel fiber-reinforced polymer mortars are mixed using the EPS-MMA-based solution as a liquid resin or binder. Polymer mortar permanent forms (PMPFs) using the EPS-MMA-based polymer mortars without and with steel fiber and crimped wire cloth reinforcements and steel fiber-reinforced polymer-impregnated mortar permanent form (PIMPF) are prepared on trial, and tested for flexural behavior under four-point (third-point) loading. The EPS-MMAbased PMPFs are more ductile than the PIMPF, and have a high load-bearing capacity. Consequently, they can replace PIMPF in practical applications.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.122-125
• /
• 2001

The objective of this research is to develop hybridized yarns for thermoplastic composites, and to examine tile effect of cooling rate on mechanical properties of the composites. The co-braided yarn utilizing carbon fibers as reinforcements and Nylon 66 fibers as matrix materials has been fabricated. Thermoplastic composites have been manufactured by the hot-press forming process. For the processing conditions, cooling rates of $-2.5^{\circ}C$/min and $-60^{\circ}C$/min have been considered. Three-point bending test and losipescu shear test were performed to investigate the effect of the cooling rate and the surface treatment of carbon fibers. SEM photographs were used to investigate the fracture surfaces of the tested samples. The cooling rate of $-60^{\circ}C$/min resulted in the higher strength and elastic modulus for bending and shear tests. The composites of the epoxy-sized carbon fibers showed the lowest strength due to the degradation of the sizing material during the thermoforming process.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.55-59
• /
• 2013

Transverse vibrations of ship's aft end and deckhouse among the various modes of hull structures are induced mainly by transverse exciting forces and moments of main engine such as ${\times}$ and h-moment. Avoidance of resonance should be made in a intial design stage in case there is a prediction for resonance between main engine and transverse modes of deckhouse. This study shows a case of change in type of main engine from 12 cylinders to 10 without modification of hull structures in engine room requested by a shipowner of 8,600 TEU class container carrier and proposes a guide to the effective ways of structural arrangement for avoiding resonance between transverse exciting force and surrounding structures of main engine in engine room through case studies.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.691-699
• /
• 2008

In the design of a foundation, settlement of the foundation may exceed allowable design criteria even with a competent bearing stratum. In such a case, a piled-raft foundation system may be adopted using piles as settlement reducing component. In this paper, Disconnected Piled Raft Foundation (DPRF) system, which installs disconnected piles underneath the raft and uses the piles as ground reinforcements, is studied as a cost effective design method against the classical piled-raft foundation system. To this end, large size loading tests were carried out on weathered ground changing area replacement ratio and length of piles. The results indicated that the settlement of the reinforced ground was reduced by 34~87% and the allowable bearing pressure increased by 70% on average from those of the unreinforced original ground, respectively. The correlating formula between the area replacement ratio and the load bearing ratio of piles were derived from the test results and numerical analysis. From the correlation, a design method determining the size and the quantity of the disconnected piles to enhance the bearing capacity of original ground to the desired value was proposed based on one inch settlement criteria.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.527-534
• /
• 2010

This study presents a simple method to improve the bond performance of reinforced concrete (RC) beams having high-strength shear reinforcement. In general, the yield strength and the ratio of shear reinforcements are the main parameters governing the shear capacity of RC beams. The yield strength of shear reinforcement, however, has little influence on the bond capacity of RC beams. Therefore, a sudden bond failure of the members with high-strength shear reinforcement can occur before flexural failure. To estimate the structural performance of the proposed method, four RC beams were cast and tested. The main test parameters were the yield strength, ratio, and reinforcing types of shear reinforcements. The experimental results indicated that the proposed method was able to effectively improve the bond performance of RC beams with high-strength shear reinforcement.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.3
• /
• pp.5-17
• /
• 2021

This study aims to investigate the causes and countermeasures for the occurrence of tension cracks in the slope of the rock mass of heavy equipment for road construction. Electric resistivity survey was performed to investigate the expandable tensile crack range. As a result of examining the distribution of soft zones in the rock mass, a low specific resistance zone was found at the bottom of the access road where tensile cracks occurred. It was confirmed that a low resistivity zone was distributed near the top of the excavation slope. Therefore, reinforcements was performed by determining the location of the possible tensile crack as the top of the excavation slope. Two rows of reinforced piles and anchors were proposed as a reinforcement method, and the slope stability analysis showed that the allowable safety factor was satisfied after reinforcements.

• Archives of design research
• /
• v.19 no.5 s.67
• /
• pp.55-64
• /
• 2006

As digital systems were introduced to automotive design in the mid 1980s, the design process has adopted many digital programs to save time compared to the conventional hand drafting. Digital technology was introduced not only to satisfy the reeds of the global environment, as the number of automobiles exported to many different parts of the world has increased, but also to save time and effort in developing several models of quality automobiles. Therefore, every automotive manufacturer in the world has expanded its virtual reality(VR) studio to establish visualization systems that visualize automobiles in the actual size and a co-operation system that enables simultaneous feedback from all of its design studios around the world. Unlike the existing design reviewing methos, the new improved feedback system is assessed as a reasonable method to evaluates and understand how the automobiles are actually manufactured in simulation. It is especially helpful when advanced products and concept cars require fast results. Other strengths of the new system include shorter development period, cost efficiency, no more manual labor, various designs within a short period of time, and realistic visualization of concepts. Large-scale products, including automobiles, need to be projected in the actual size and high clarity through the Power-wall System and are examined in a virtual space called a Cave. Therefore, it took much time to establish digital infrastructure. An infrastructure would constantly require system improvement and performance enhancement, but it is certain that now is the right time for the take-off to utilizing the strengths of digital design and improve the weaknesses. In this respect, this study provided an understanding of the importance of digital design based on digital reinforcements and examined an effective utilization of digital technology for an efficient development of automobiles in the future.